Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Halogen-free Polymer Donors Based on 3,4-Dicyanothiophene for High-performance Polymer Solar Cells

Halogen-Free Donor Polymers Based on Dicyanobenzotriazole with Low Energy Loss and High Efficiency in Organic Solar Cells

Developing Halogen‐Free Polymer Donors for Efficient Nonfullerene Organic Solar Cells by Addition of Highly Electron‐Deficient Diketopyrrolopyrrole Unit

Chlorination of Low-Band-Gap Polymers: Toward High-Performance Polymer Solar Cells

Binary all-polymer solar cells with efficiency over 17% by fine-tuning halogenated thiophene linkers of polymer acceptors

Chlorination of Conjugated Side Chains to Enhance Intermolecular Interactions for Elevated Solar Conversion

Carboxylate-Substituted Polythiophenes For Efficient Fullerene-Free Polymer Solar Cells: The Effect Of Chlorination On Their Properties

3,4‐Dicyanothiophene—a Versatile Building Block for Efficient Nonfullerene Polymer Solar Cells

Over 14% Efficiency in Polymer Solar Cells Enabled by a Chlorinated Polymer Donor

Donor–Acceptor Copolymers with Rationally Regulated Side Chain Orientation for Polymer Solar Cells Processed by Non-Halogenated Solvent

Wide Band-gap Two-dimension Conjugated Polymer Donors with Different Amounts of Chlorine Substitution on Alkoxyphenyl Conjugated Side Chains for Non-fullerene Polymer Solar Cells

Alkylsilyl Functionalized Copolymer Donor for Annealing‐Free High Performance Solar Cells with over 11% Efficiency: Crystallinity Induced Small Driving Force

17.1 %-Efficient Eco-Compatible Organic Solar Cells From A Dissymmetric 3d Network Acceptor

High-performance polymer solar cells based on terpolymer composed of one donor and two acceptors processed with non-halogenated solvent

Polymer Based on Asymmetrically Halogenated Benzotriazole Enables High Performance Organic Solar Cells Prepared in Nonhalogenated Solvent

Modulating Chlorination Position on Polymer Donors for Highly Efficient Nonfullerene Organic Solar Cells

A Donor Polymer Based on a Difluorinated Pentathiophene Unit Enabling Enhanced Performance for Nonfullerene Organic Solar Cells

Chlorinated Benzo[1,2‐b:4,5‐c′]dithiophene‐4,8‐dione Polymer Donor: A Small Atom Makes a Big Difference

Enhancing the Performance of Polymer Solar Cells by Using Donor Polymers Carrying Discretely Distributed Side Chains.

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Fluorinated And Alkylthiolated Polymeric Donors Enable Both Efficient Fullerene And Nonfullerene Polymer Solar Cells