Abstract:TiO2 nanomaterials, especially one-dimensional TiO2 nanofibers fabricated by electrospinning, have received considerable attention in the past two decades, for a variety of basic applications. However, their safe use and easy recycling are still hampered by the inherently subpar mechanical performance. Here, we toughened polycrystalline TiO2 nanofibers by introducing Al3+-species at the very beginning of electrospinning. The resultant long-and-continuous TiO2 nanofibers achieved a Young's modulus of 653.8 MPa, which is ca. 25-fold higher than that of conventional TiO2 nanofibers. Within each nanofiber, amorphous Al2O3-based oxide effectively hindered the coalescence of TiO2 nanocrystals and potentially repaired the surface groves. The solid-state 17O-NMR spectra further revealed the toughening strategy on a molecular scale, where relatively flexible Ti-O-Al bonds replaced rigid O-Ti-O bonds at the interfaces of TiO2 and Al2O3. Moreover, the modified TiO2 nanofibers exhibited superb sinter-resistance, without cracking over 900 °C, which was dynamically monitored by TEM. Therefore, flexible-in-rigid TiO2 fibrous mats can be facilely folded into 3D sponges through origami art. As a potential showcase, the TiO2 sponges were demonstrated as a duarable and renewable filtrator with a high filtration efficiency of 99.97% toward PM2.5 and 99.99% toward PM10 after working for 300 min. This work provides a rational strategy to produce flexible oxide nanofibers and gives an in-depth understanding of the toughening mechanism from the macro-scale to the molecular-scale.

Effect of high-pressure vapor on the microstructure and mechanical properties of TiO2 continuous fibers

Titanium Dioxide Fibers Prepared by Sol–gel Process and Centrifugal Spinning

Improving UV Resistance of Aramid Fibers by Simultaneously Synthesizing TiO2 on Their Surfaces and in the Interfaces Between Fibrils/Microfibrils Using Supercritical Carbon Dioxide

Preparation and Photocatalytic Property of Dendritic TiO<sub>2</sub>/VO<sub>x</sub> Nanofibers

Effect of Heat-treatment Atmosphere on Preparation of Continuous Zirconia Fibers

Preparation of TiO2-NT Coated PET Fabrics and Their Formaldehyde Degrading Effect

Effects of Preparation Parameters on Room Temperature Formation of Vanadium-Doped Tio2 Nanocrystalline Powder

High Efficient and Continuous Surface Modification of Carbon Fibers with Improved Tensile Strength and Interfacial Adhesion

Crystallization Process and Microstructure of Sol–gel Derived Pb0.9La0.1Ti0.875O3 Fine Fibers with a Novel Heat-Treatment Process

Flexible-in-rigid Polycrystalline Titanium Nanofibers: a Toughening Strategy from a Macro-Scale to a Molecular-Scale

Development of Lutetium Oxide Continuous Fibers with Excellent Mechanical Properties

Fabrication of High‐Strength Continuous Zirconia Fibers and Their Formation Mechanism Study

Influence of Tension on the Oxidative Stabilization Process of Polyacrylonitrile Fibers

Effects of the atmosphere on the high tensile strength and robust flexibility of Lu2O3 fibrous membrane

Study on the structural evolution of polyacrylonitrile fibers in stepwise heat treatment process and its relationship with properties

Fabrication of Oxygen-Deficient TiO 2 Coatings with Nano-Fiber Morphology for Visible-Light Photocatalysis

Hyperbranched Polyester-Stabilized Nanotitania-Coated Vectran Fibers with Improved UV-Blocking Performance (vol 300, pg 64, 2015)

Effect of vapor grown carbon fiber content on microstructure and tensile properties of Ti64/TiC composite fabricated by powder metallurgy method

Effect of Accelerating Gas Flow on Pore Structure and Mass Transport Property of Vacuum Cold Sprayed TiO2 Coatings Using Strengthened Nanostructured Powder

The Effect of Oxidation Treatment with Supercritical Water/Hydrogen Peroxide System on Intersurface Performance for Polyacrylonitrile-Based Carbon Fibers

Effects of Solvent Treatment on the Formation of Oxygen Vacancy in TiO2 via Vacuum Annealing