Abstract:Non-grain oriented electrical steels (NGOES) are typically used in electric applications with rotating magnetic fields and thus essential for the production of electric motors. The increasing number of electric vehicles results in a growing demand for electrical steel sheets used in the stacked laminations of rotor and stator components. E-mobility applications require the best possible magnetic properties for optimum performance and efficiency, especially at high frequencies. In addition, increased mechanical strength is necessary to withstand the centrifugal forces resulting from high revolution speeds. Chemical composition, microstructure and crystallographic texture strongly influence the magnetic properties, whereas the mechanical properties are mainly affected by the chemical composition and grain size. Optimizing the texture is a possible method for improving the magnetic properties without significantly compromising the mechanical strength. In this work a special processing route for the production of 3.25% Si NGOES sample material has been studied, using laboratory cold rolling and annealing facilities. Compared to the classical processing route of single stage cold rolling and annealing, this alternative method involves two cold rolling steps with an intermediate annealing treatment between the first and second rolling sequence and a final annealing treatment after the second rolling step. The samples were produced with different intermediate thicknesses, changing the amount of cold rolling deformation of each sample variation. The degree of deformation affects the recrystallization and grain growth behavior and thus the resulting microstructure and texture. The microstructural and textural evolution was investigated in the hot rolled, intermediate annealed and final annealed state using electron backscatter diffraction (EBSD). Finished samples were additionally examined using magnetic testing and tensile testing. The results indicate a correlation between the intermediate thickness and the final grain size of the steel samples. Furthermore, the highly grain size dependent mechanical strength and magnetic losses are influenced. EBSD-data were used to interpret the texture and to calculate a parameter describing the magnetic quality of the texture. The results show a strong improvement of magnetically favorable texture components along with increasing intermediate thickness, enabling significantly better polarization values in rolling direction and transversal direction. However, anisotropy of the magnetic properties increases as well due to the textural changes.

Evolution of Crystallographic Texture and Its Impact on Magnetic Losses of Non‐oriented Electrical Steel

Effect of Heat-Treatment Process on Magnetic Characteristics of Grain-Oriented Electrical Steel

Study on Influence of Microstructure and Thermal Treatment on Magnetic Losses from Non-Oriented Silicon Electrical Steel

Effect of Annealing Temperature and Time on the Magnetic Properties and Magnetic Anisotropy of a Temper-Rolled, Semi-processed Non-oriented Electrical Steel

Research Situation of Annealing Process for Non-oriented Electrical Steel

Effects by the microstructure after hot and cold rolling on the texture and grain size after final annealing of ferritic non-oriented FeSi electrical steel

Effect of Cold Rolling Prior to Annealing on the Grain Size-Energy Losses Relationship in a Low Carbon Grain Non-Oriented Semi-Processed Electrical Steel

Microstructural and textural evolution of double stage cold rolled non-grain oriented electrical steel

Influence of stress relief annealing temperature on the cutting edge microstructure and on the recovery of magnetic properties of grain oriented electrical steel

Evolution of Power Losses in Bending Rolled Fully Finished NO Electrical Steel Treated under Unconventional Annealing Conditions

Texture evolution in grain-oriented electrical steel during hot band annealing and cold rolling

Microstructure, texture and magnetic properties of the semi-processed strip-cast non-oriented electrical steel

Effect of annealing on magnetic properties of high-manganese non-oriented electrical steel

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

The effect of grain size before cold rolling on the magnetic properties of thin-gauge non-oriented electrical steel

A Novel Approach for Evaluating the Influence of Texture Intensities on the First Magnetization Curve and Hysteresis Loss in Fe-Si Alloys

Magnetic anisotropy reduction of non-grain oriented electrical steel due to different stress relief annealing temperatures

Microstructure and Texture Development in a Thin Gauge Non Oriented Electrical Steel

Effect of stress relief annealing temperature and atmosphere on the microstructure and magnetic properties of non-oriented electrical steels

Optimum Magnetic Properties of Non-Oriented Electrical Steel Produced by Compact Strip Production Process

Significant effect of as-cast microstructure on texture evolution and magnetic properties of strip cast non-oriented silicon steel