Abstract:Non-grain oriented electrical steels (NGOES) are typically used in electric applications with rotating magnetic fields and thus essential for the production of electric motors. The increasing number of electric vehicles results in a growing demand for electrical steel sheets used in the stacked laminations of rotor and stator components. E-mobility applications require the best possible magnetic properties for optimum performance and efficiency, especially at high frequencies. In addition, increased mechanical strength is necessary to withstand the centrifugal forces resulting from high revolution speeds. Chemical composition, microstructure and crystallographic texture strongly influence the magnetic properties, whereas the mechanical properties are mainly affected by the chemical composition and grain size. Optimizing the texture is a possible method for improving the magnetic properties without significantly compromising the mechanical strength. In this work a special processing route for the production of 3.25% Si NGOES sample material has been studied, using laboratory cold rolling and annealing facilities. Compared to the classical processing route of single stage cold rolling and annealing, this alternative method involves two cold rolling steps with an intermediate annealing treatment between the first and second rolling sequence and a final annealing treatment after the second rolling step. The samples were produced with different intermediate thicknesses, changing the amount of cold rolling deformation of each sample variation. The degree of deformation affects the recrystallization and grain growth behavior and thus the resulting microstructure and texture. The microstructural and textural evolution was investigated in the hot rolled, intermediate annealed and final annealed state using electron backscatter diffraction (EBSD). Finished samples were additionally examined using magnetic testing and tensile testing. The results indicate a correlation between the intermediate thickness and the final grain size of the steel samples. Furthermore, the highly grain size dependent mechanical strength and magnetic losses are influenced. EBSD-data were used to interpret the texture and to calculate a parameter describing the magnetic quality of the texture. The results show a strong improvement of magnetically favorable texture components along with increasing intermediate thickness, enabling significantly better polarization values in rolling direction and transversal direction. However, anisotropy of the magnetic properties increases as well due to the textural changes.

Magnetic anisotropy reduction of non-grain oriented electrical steel due to different stress relief annealing temperatures

Influence of stress relief annealing temperature on the cutting edge microstructure and on the recovery of magnetic properties of grain oriented electrical steel

Effects of stress relief annealing in NGO steels

Effect of stress relief annealing temperature and atmosphere on the microstructure and magnetic properties of non-oriented electrical steels

Effect of Annealing Temperature and Time on the Magnetic Properties and Magnetic Anisotropy of a Temper-Rolled, Semi-processed Non-oriented Electrical Steel

Study on Influence of Microstructure and Thermal Treatment on Magnetic Losses from Non-Oriented Silicon Electrical Steel

Effect of Cold Rolling Prior to Annealing on the Grain Size-Energy Losses Relationship in a Low Carbon Grain Non-Oriented Semi-Processed Electrical Steel

Microstructural and textural evolution of double stage cold rolled non-grain oriented electrical steel

Evolution of Crystallographic Texture and Its Impact on Magnetic Losses of Non‐oriented Electrical Steel

The Research of Non-Oriented Electrical Steel Processed by Stress Relief Annealing Experiments

Anomalous magnetization induced by local chemistry fluctuations in Mn-containing α'-martensite

Evolution of the Magnetic Anisotropy and Magnetostriction in Co-based Amorphous Alloys Microwires Due to Current Annealing and Stress -Sensory Applications

Research Situation of Annealing Process for Non-oriented Electrical Steel

Effect of cold drawing reduction rate on edge-to-center-characterized microstructure and orientation alongside residual stresses in conjunction with magnetic properties of low-carbon high-alloy ferromagnetic steel

Influences of annealing temperature on microstructure and magnetic properties of non-oriented electrical steels

Influence of tensile stress on the magnetic properties of ultra-thin grain-oriented electrical steel

The significance of hot rolled microstructure controlled by fine-tuning Al content to texture evolution and magnetic properties of low silicon non-oriented electrical steels

Magnetic Performance Improvement Caused by Tensile Stress in Equivalent Iron Core Fabricated by High-Strength Non-Oriented Electrical Steel

Effect of sub-micron deformations at opposing strain rates on the micromagnetic behaviour of non-oriented electrical steel

Effects of hot rolled microstructure after twin-roll casting on microstructure, texture and magnetic properties of low silicon non-oriented electrical steel

Effect of rolling process on magnetic properties of Fe-3.3 wt% Si non-oriented electrical steel