Abstract:Ni-rich layered cathode materials are important candidates for lithium-ion batteries used for applications requiring high energy density, such as electric vehicles and mobile electronic devices. However, comparing with low Ni content NMC, Ni-rich NMCs frequently exhibit fast capacity decay and relatively shorter lifetime due to the formation of more reactive surface with high Ni content. Previous reports demonstrated that Ni-rich NMCs are sensitive to the CO 2 and water in the air during ambient storage, because of these oxidizing gases can lead to the formation of surface impurities such as Li 2 CO 3 and LiOH. [1] these surface impurities can react with electrolyte during the electrochemical cycling process and form a nonuniform cathode/electrolyte interface (CEI) layer. Surface instability of Ni-rich NMCs can also cause problems during the large-scale electrode preparation, and material storage. Research results reported in the literature have suggested that the degradation of Ni-rich NMCs could be attributed to the reduction of Ni and evolution of active oxygen species as well as the side reaction between the surface impurities and the electrolyte. [2-3] However, only limited experimental results have been reported about the formation mechanism of surface impurities and side reaction during the battery cycling for Ni-rich NMCs. Therefore, it is very important to develop an in-situ characterization method to reveal the CO 2 and moisture effects on the surface chemistry of Ni-rich NMCs. Synchrotron-based Ambient-Pressure XPS (AP-XPS) is a powerful technique with controllable gas environments and tunable energy. These enable us to probe the surface chemistry evolution of the samples in-situ in atmospheric gas environments with different depth profile. Taking these advantages, we have systematically investigated the CO 2 and moisture effect on the LiNi 0.94 Co 0.06 O 2 cathode material with and without Al doping using AP-XPS technique. Preliminary results showed that only Ni 2+ can be observed in NC sample surface after exposed to CO 2 environment even measured at 2000 eV with probing depth of ~9 nm. In contrast, characteristic peak of Ni 3+ still exists in NCA sample, even measured at 1200 and corresponding to probing depth of ~5.5 nm. These results show that better surface stability (less Ni 2+ at surface) can be achieved by Al doping. We also comprehensively investigated the depth profile of CEI layer of NMC cathode materials with different Ni content and found that CEI composition really depends on Ni content, dopant as well as the cut off voltage for charging. These results will be presented at the meeting. [1] You et al. Angewandte Chemie , 572018 (2018) 6480-6485. [2] Shizuka et al. Journal of Power Sources , 166 (2007) 233-238. [3] Jung et al. Journal of The Electrochemical Society , 165 (2) (2018) A132-A141. Acknowledgement The work was supported by the Assistant Secretary for Energy Efficiency and Renewable Energy, Vehicle Technology Office of the U.S. DOE through the Advanced Battery Materials Research (BMR) Program, including Battery500 Consortium under contract No. DE-SC0012704.

The Formation of Residual Lithium Compounds on Ni‐Rich NCM Oxides: Their Impact on the Electrochemical Performance of Sulfide‐Based ASSBs

Formation and Detriments of Residual Alkaline Compounds on High‐Nickel Layered Oxide Cathodes

The Formation, Detriment and Solution of Residual Lithium Compounds on Ni-Rich Layered Oxides in Lithium-Ion Batteries

Reduction of Surface Residual Lithium Compounds for Single-Crystal LiNi0.6Mn0.2Co0.2O2 Via Al2O3 Atomic Layer Deposition and Post-Annealing

Formation and Effect of Residual Lithium Compounds on Li-Rich Cathode Material Li-1.35[Ni0.35Mn0.65]O-2

Formation Mechanism and Removal Strategy of Residual Lithium Compounds on Nickel-Rich Cathode Materials

(Digital Presentation) Simultaneous Transforming Residual Lithium Compounds and Stabilizing Surface Lattice Oxygen for Ni-Rich Cathode Via Atomic Layer Deposition and Post-Annealing

Air- and Moisture Robust Surface Modification for Ni-Rich Layered Cathode Materials for Li-Ion Batteries

(Invited) Probing the in-Situ Surface Chemistry of Ni-Rich LiNi <sub>x</sub> Co <sub>y</sub> Mn <sub>z</sub> O<sub>2</sub> (x+y+z=1) Cathode Materials Using Synchrotron-Based Ambient-Pressure X-Ray Photoelectron Spectroscopy

(Invited) Probing the in-Situ Surface Chemistry of Ni-Rich LiNi x Co y Mn z O2 (x+y+z=1) Cathode Materials Using Synchrotron-Based Ambient-Pressure X-Ray Photoelectron Spectroscopy

Improving Storage Performance and Lattice Oxygen Stability of Single Crystal LiNi0.925Co0.03Mn0.045O2 by Integrating Utilization of Surface Residual Lithium and Lattice Modulation

Ni-Rich Co-less Cathode Materials with LiYO2 and Y3+ Modification Toward Improved Storage Performance Against Ambient Air for Lithium-Ion Batteries

Residual Alkali-Evoked Cross-Linked Polymer Layer for Anti-Air-sensitivity LiNi0.89Co0.06Mn0.05O2 Cathode

Stabilizing Effect of a Hybrid Surface Coating on a Ni-Rich NCM Cathode Material in All-Solid-State Batteries

Strategies of Removing Residual Lithium Compounds on the Surface of Ni‐Rich Cathode Materials †

Atomic scale evolution of the surface chemistry in Li[Ni,Mn,Co]O2 cathode for Li-ion batteries stored in air

Electrochemical Characteristics of Layered Transition Metal Oxide Cathode Materials for Lithium Ion Batteries: Surface, Bulk Behavior, and Thermal Properties

Enhanced Electrochemical Stability and Extended Cycle Life in Sulfide-Based All-Solid-State Batteries: The Role of Li10 SnP2 S12 Coating on Ni-Rich NCM Cathode

Outstanding electrochemical performances of the all-solid-state lithium battery using Ni-rich layered oxide cathode and sulfide electrolyte

Ni-Rich Cathode Active Materials Surface Degradation in Ambient Air with Stabilisation Treatment Proposal

Removing lithium residues via H3BO3 washing and concurrent in-situ formation of a lithium reactive coating on Ni-rich cathode materials toward enhanced electrochemical performance