Microfluidics: Advanced Platform for Designing Polymeric Microparticles, Microcapsules, and Microfibers
Shin‐Hyun Kim,Liang‐Yin Chu
DOI: https://doi.org/10.1002/pol.20220220
IF: 3.046
2022-01-01
Journal of Polymer Science
Abstract:Microfluidic technology has dramatically progressed over the last 20 years. Microfluidics provides precise control of flows confined in microchannels, which is very useful for the biological analysis of a small volume of samples. At the same time, due to the excellent controllability over mass transfer and heat transfer, microfluidics has served as an advanced platform for materials synthesis and production as miniatured continuous reactors. In particular, microfluidics produces emulsion drops and jets with highly controlled sizes and uniformity for the simultaneous injection of two or more fluids in microchannels. Each emulsion drop provides physical confinement or isolated small-volume reaction for the production of microparticles and microcapsules. Recent advances in microfluidics enable the controlled production of drops-in-drops or multiple-emulsion drops, serving as advanced templates for materials production. Jets can be stabilized in microchannels by the physical confinement of interfaces, which have been used as templates to produce functional microfibers. Without templating drops or jets, the flow in the microchannels can be segmented to produce microcompartments or microparticles continuously by a localized chemical reaction triggered by regioselective irradiation of flashing light, which is referred to as the flow lithography. Microfluidics, serving as a most advanced platform for materials synthesis, has provided elaborate control over the dimensions, structures, and chemical components of microparticles, microcapsules, and microfibers, which is otherwise difficult to achieve. Although the production throughput is somewhat limited at the current stage, significant improvement has been made and will proceed for commercial-scale production. This special issue on Functional Polymeric Materials by Microfluidics presents a series of research articles with novel ideas, and in-depth reviews contributed by leading groups in the field. The polymeric materials produced by microfluidics in this issue are classified into three categories of microparticles, microcapsules, and microfibers. The review article by Zhu et al. provides an overview of polymeric microparticles with surface textures created by droplet microfluidics. Surface microstructures are appealing for drug delivery, cellular immunity, and cell capture due to their large surface-to-volume ratio and biomimetic structural properties. The review summarizes the methods to produce complex surface microstructures from the smooth interface of emulsion drops, explains how the microstructures are used for the applications, and discusses the current challenges and outlook. The review article by Lee et al. summarizes droplet microfluidics-assisted methods for producing soft microparticles, mechanical characterization techniques, and various applications as microcarriers, bio-inks, and sensors. In particular, the theoretical models for elastic properties of soft microparticles are introduced, and the relationship between the physical parameters and elastic properties is discussed in the review. The research article by Lee et al. reports a simple and reproducible method to fabricate graphically-encoded microspheres. During the dewetting of polyethylene glycol diacrylate (PEGDA) confined in micromold in the presence of a wetting fluid, parts of the PEGDA are locally entrapped, which results in imprinted graphical code in photocured microspheres. The encoded microspheres are useful as a suspension array for multiplex immunoassay through surface functionalization. The research article by Chen et al. presents a novel microfluidic approach to produce polyhedral milliparticles with controlled shape through flow lithographic technique. The milliparticles with rectangular pyramid shape are produced by illuminating a photocurable flow in a triangular millichannel with ultraviolet through a triangular photomask. The shape can be further modulated by altering the relative positions between the microchannel and the ultraviolet. Various geometries of monodisperse polyhedral milliparticles with both centrosymmetric and noncentrosymmetric structures, including tetrahedra, pentahedra, and hexahedra, are produced by tuning the rotation angle and translation displacement. The research article by Bong et al. presents a protocol for direct cell-adhesion promoter functionalization of the poly(ethylene glycol) (PEG) microparticles produced by stop-flow lithography. With aza-Michael reaction between remnant unreacted acrylate groups in the microparticles and amine groups in cell-adhesion promoters, particles are directly conjugated with cell-adhesion promoters, which significantly enhances the cell-adhesion capabilities of the microparticles. The research article by Chen et al. presents the printing technique of photonic microspheres with a microfluidic drop maker installed in a dispenser. The photonic microspheres are produced by crystallization of colloidal particles in emulsion drops, which are printed on the target surface by an automated dispenser. Moreover, magnetoresponsive Janus photonic microbeads are produced by gravity-induced fusion of printed drops, which enables the color switching through magnetic-field-dictated rotation of the Janus microbeads. The research article by Kim et al. presents the hydrogel-shelled biodegradable microspheres as drug carriers. The microspheres are templated by oil-in-water-in-oil double-emulsion drops, where the innermost oil drop of polylactic acid is consolidated to a biodegradable core, and the middle water shell is converted to a hydrogel of calcium-alginate. The hydrogel shell provides a consistent rate of sustained release of drugs from the biodegradable core by preventing direct exposure of the core to the surroundings and secures high suspension stability by increasing the compatibility of the hydrophobic core with the continuous water. The research article by Vladisavljević et al. presents the polymer-shelled microcapsules containing good solvents for carbon dioxide. The microcapsules are produced from water-in-oil-in-water double-emulsion drops by photopolymerizing monomers in the oil shell. For various polymeric materials, mechanical stability and carbon dioxide permeability are comparatively evaluated. Among them, the carbon nanotube-loaded polydimethylsiloxane shell shows promising performance for simultaneous removal of carbon dioxide and volatile organic compounds. The research article by Xu et al. reports highly stretchable wound dressing composed of helical hydrogel microfibers. The calcium-alginate helical microfiber is produced by microfluidic spinning. The microfiber is packed, and the void is filled with polyacrylamide to make a composite polymer membrane. The composite film shows excellent stretchability and good skin adhesion, providing great potential for the use of wound dressings. The research article by Yoon et al. reports the microfluidic production of highly stretchable conducting microfibers. The microfibers are produced to have a double network structure by the simultaneous coagulation of chitosan and photocrosslinking of N-isopropylacrylamide and N-diethylacrylamide in a jet. The hydrogel is converted to ionogel through the exchange of the medium of the microfibers with an aqueous electrolyte of lithium bis(trifluoromethanesulfonyl)imide. The ionogel microfibers exhibit high conductivity, stretchability and dry-free properties, which are promising for soft electronics and wearable devices. The research article by Guo et al. reports the microfluidic spinning technique for the production of β-phase enriched piezoelectric poly(vinylidene fluoride) (PVDF) microfibers. The microfibers are produced inside the microfluidic channel from the jet of PVDF solution in an aqueous solution of PEG by the mass transfer-induced phase inversion. The microfibers are weaved into meshes and fabrics, which are used for in situ and real-time human motion monitoring. We believe the comprehensive reviews and novel original research articles in this issue can provide a well-organized, informative introduction to the field and inspire researchers to make new ideas. Also, we hope that the introduction of microfluidic technology to the polymer community through this issue can create great opportunities for collaboration between scientists and engineers in two distinct fields of microfluidics and polymers. Lastly, we would like to thank all the authors, reviewers, and editorial staffs who contributed to this special issue.