Abstract:The effects of isothermal temperature and duration on the microstructures and anisotropic mechanical properties of bimodal 6A02 Al semi-solid billets were studied. These semi-solid billets were fabricated by semi-solid isothermal treatment of hot extruded aluminum alloy (SSITHEAA) method. Elongated and equiaxed grains owning different dislocation densities coexisted at 610–650 °C for 5–30 min. With the increase of temperature, the intensities of micro-textures and intragranular dislocation decreased. The average Schmid factors in transverse directions were still larger than those along extruding directions, preliminarily predicting anisotropic features from the perspective of grain orientation. The anisotropic features of bimodal semi-solid microstructures were verified firstly by uniaxial tensile tests in 0°, 45°, and 90° directions, among which 0 ° specimen at 610 °C/ 20 min exhibited the highest tensile strength and ductility (yield strength σy of 103.8 MPa, maximum tensile strength σmax of 286.9 MPa, and elongation δ of 22.0%). Different from microstructures at solid temperatures, recrystallization degraded mechanical strength of semisolid microstructures to some degree once the grain boundaries were soaked with liquid phase. The dislocation strengthening inside the deformed grains and solid solution strengthening were two dominant strengthening mechanisms. Besides, the elongated grains improved the mechanical properties through dislocation pileup inside the grains, "bridging" effect, "necking" effect and decreasing the content of both flaws and liquid phase. The in-plane anisotropy (IPA) factor indicated that the elongation bore the most serious anisotropy. On the whole, the isotropy of 650 °C/20 min billet was the best, and the corresponding IPA values of σy, σmax and δ were 21.9%, 26.2%, and 47.0%, respectively. For 0° specimens, ductile fracture was dominant, but brittle characteristic was increasingly significant for 45° and 90° specimens.

Cu strengthened Al-Si-Cu semi-solid billet fabricated by liquid phase reaction sintering

Microstructure Evolution and Mechanical Properties of Al-8wt. % Si Semi-Solid Billet Fabricated by Powder Metallurgy Liquid Phase Reaction Sintering

Microstructural properties, thermodynamics and kinetics of Al-Si semi-solid billet fabricated by liquid phase reaction sintering

Achieving strength-ductility synergy in Al-4.5 wt%Cu binary alloy through semisolid isothermal treatment coupled with ECAP

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Achieving high strength in selective laser melting AlSi10Mg alloy by adding microsized pure Cu particles

Development of a novel high strength Al-Si-Cu-Ni alloy by combining micro-alloying and squeeze casting

Enhanced Strength-Ductility Synergy of Homogeneous Isomeric Al–Cu–Mg Sheet Prepared by Powder Metallurgy

Effect of G-phase and heterogeneous deformation-induced strengthening on the mechanical properties of Cu-20Ni-20Mn-2Fe-1Si alloy

Precipitates strengthening mechanism of a new squeeze-cast Al-Cu-Li-Mn alloy with high strength and ductility

Fabrication and strengthening mechanism of dual-phased and bimodal-sized (Si3N4p + TiB2p)/6061Al hybrid composite

Semisolid Compression Brazing of Al50Si Alloy Using Zn-Al-Cu Filler Metal Assisted by SiC Particles

Microstructural evolution and anisotropic tensile properties of a bimodal 6A02 Al semi-solid billet

Semi-solid Billet Prepared by Radial Forging Combined with Unidirectional Compression Recrystallization and Partial Melting

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Achieving Simultaneous Enhancement of Strength and Ductility in Al Matrix Composites by Employing the Synergetic Strengthening Effect of Micro- and Nano-Sicps

Effect of Multistage Solid Solution Treatment on Microstructure and Properties of Al-6.5Si-5.5Cu-0.2Zr-0.01Sr-0.06Ti-0.2Y Alloy

Precipitation behavior and mechanical properties of Al-Zn-Mg-Cu matrix nanocomposites: Effects of SiC nanoparticles addition and heat treatment

Enhancing Mechanical Performances by Unconventional Si Precipitates Obtained in Pressure-Induced Al-Si-Cu-(Mg) Solid Solutions

Preparation and properties of Al2O3 dispersed fine-grained W-Cu alloy

Microstructure and mechanical properties of ultrafine grained Cu-0.8 wt%C alloy with a bimodal microstructure produced by powder metallurgy techniques