Abstract:The feasibility of a Mg-Zn-Zr alloy for biomedical applications was studied through microstructure characterization, corrosion tests in different biological media, and cell proliferation, differentiation and adhesion tests. Corrosion tests showed that the ZK60 alloy in the as-extruded state with finer grain sizes exhibited slower corrosion rates than the same alloy in the as-cast state. The tests in different biological fluids showed that the corrosion rates of the as-cast and as-extruded ZK60 alloy in DMEM + FBS were the highest, while those in Hank's solution were the lowest. The corrosion rate of the as-extruded ZK60 alloy was similar to the corrosion rates of other commercial magnesium alloys, namely the die-cast AZ910, die-cast AM50, extruded AZ31 and extruded WE43 alloys. The results obtained from the indirect cytotoxicity evaluation showed that the 100% concentrated cast and extruded ZK60 alloy extracts resulted in significantly reduced cell numbers and total protein amounts, as compared to the negative control. The cell number and total protein amount increased with the gradual dilution of the extracts, but the protein normalized ALP activity showed an opposite trend. For the direct assay, L-929 and MG63 cells exhibited good adhesion with spread pseudopod on the surface of extruded ZK60 alloy samples after 24 h culture. In short, the as-extruded ZK60 alloy could be a good candidate material for biodegradable implants. (C) 2011 Elsevier B.V. All rights reserved.

Tensile and biodegradable properties of Mg-6.0Zn-1.0Nd-0.5Zr alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and Mechanical Properties of Mg–4.5Zn–xNd (x=0, 1 and 2, Wt%) Alloys

Study on Microstructure and Tensile Mechanical Properties of As-Extruded Mg-xZn-2.8Nd-0.6Zr-0.6Cd Alloy

In Vitro Degradation Performance and Biological Response of a Mg–Zn–Zr Alloy

Effects of minor Nd and Er additions on the precipitation evolution and dynamic recrystallization behavior of Mg–6.0Zn–0.5Mn alloy

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Development of a new magnesium alloy ZW21

Nd-induced honeycomb structure of intermetallic phase enhances the corrosion resistance of Mg alloys for bone implants

Study on the Microstructure and Mechanical Property of High Strength Mg-Nd-Zn-Zr Alloy

Microstructural Characteristics and Mechanical Properties of Cast Mg–3Nd–3Gd–xZn–0.5Zr Alloys

The Effect of Gd and Zn Additions on Microstructures and Mechanical Properties of Mg-4sm-3nd-Zr Alloy

Microstructural Characteristics and Mechanical Properties of the Hot Extruded Mg-Zn-Y-Nd Alloys

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Effect of Nd addition on the microstructure and mechanical properties of extruded Mg-Gd-Zr alloy

A good balance between strength and ductility in Mg–Zn–Mn-Gd alloy

Microstructure and Mechanical Properties of Mg-7Zn-3Al Alloy with Nd and Y Additions

Microstructure and mechanical properties of hot-rolled Mg–Zn–Nd–Zr alloys

Microstructure and mechanical properties of Mg–4Al–4Nd–0.5Zn–0.3Mn alloy

A novel die-casting Mg alloy with superior performance: Study of microstructure and mechanical behavior