Abstract:In this work, a multifunctional magnetic field‐assisted interface embedding strategy is developed to construct 2D/3D composite perovskite films. The composite structure can improve crystallinity, passivate defects, promote vertical hole transport, and form a good surface and internal encapsulation of 3D perovskite. As a result, the fabricated rigid and flexible devices achieve the high efficiency of 24.21% and 21.23%, respectively. Perovskite solar cells (PSCs) based on 2D/3D composite structure have shown enormous potential to combine high efficiency of 3D perovskite with high stability of 2D perovskite. However, there are still substantial non‐radiative losses produced from trap states at grain boundaries or on the surface of conventional 2D/3D composite structure perovskite film, which limits device performance and stability. In this work, a multifunctional magnetic field‐assisted interfacial embedding strategy is developed to construct 2D/3D composite structure. The composite structure not only improves crystallinity and passivates defects of perovskite layer, but also can efficiently promote vertical hole transport and provide lateral barrier effect. Meanwhile, the composite structure also forms a good surface and internal encapsulation of 3D perovskite to inhibit water diffusion. As a result, the multifunctional effect effectively improves open‐circuit voltage and fill factor, reaching maximum values of 1.246 V and 81.36%, respectively, and finally achieves power conversion efficiency (PCE) of 24.21%. The unencapsulated devices also demonstrate highly improved long‐term stability and humidity stability. Furthermore, an augmented performance of 21.23% is achieved, which is the highest PCE of flexible device based on 2D/3D composite perovskite films coupled with the best mechanical stability due to the 2D/3D alternating structure.

Self‐Assembly of 0D/3D Perovskite Bi‐Layer from a Micro‐Emulsion Ink

Surface Planarization‐Epitaxial Growth Enables Uniform 2D/3D Heterojunctions for Efficient and Stable Perovskite Solar Modules

Deterministic fabrication of 3D/2D perovskite bilayer stacks for durable and efficient solar cells

Surface Reconstruction and In Situ Formation of 2D Layer for Efficient and Stable 2D/3D Perovskite Solar Cells

Sn Perovskite Solar Cells via 2D/3D Bilayer Formation through a Sequential Vapor Process

Conformal Imidazolium 1D Perovskite Capping Layer Stabilized 3D Perovskite Films for Efficient Solar Modules

Self-Assembly of 2D/3D Perovskites by Crystal Engineering for Efficient Air-Processed, Air-Stable Inverted Planar Perovskite Solar Cells

Highly Efficient and Stable 2D 3D Perovskite Solar Cells Fabricated by Interfacial Modification

Scalable Fabrication of High‐Performance Perovskite Solar Cell Modules by Mediated Vapor Deposition

Lattice Matching Propels Customized-Dimensionality 2D/3D Perovskite Heterojunctions for High-Performance Photovoltaics

Fabricating Efficient and Stable Quasi-3D and 3D/2D Perovskite Solar Cells with 2D-Sheets Connected by Inorganic Type Ionic-Bond

Construction of 2d/3d/2d‐structured Perovskite for High‐Performance and Stable Solar Cells

Magnetic Field‐Assisted Interface Embedding Strategy to Construct 2D/3D Composite Structure for Stable Perovskite Solar Cells with Efficiency Over 24%

Stability-enhanced perovskite heterointerfaces and solar cells via strongly anchored and sterically hindered ligands

Fully solution-processed phase-pure 3D/2D perovskite bilayer heterojunctions

In‐Situ Self‐Assembly Dipole Shielding Layer Toward Efficient and Stable Inorganic Perovskite Solar Cells

Modulation of Colloidal Assembly Behavior Enables Printable Low-Dimensional Perovskite Photovoltaics

Stabilization of 3D/2D perovskite heterostructures via inhibition of ion diffusion by cross-linked polymers for solar cells with improved performance

Phase Pure 2D Perovskite for High‐Performance 2D–3D Heterostructured Perovskite Solar Cells

2D or not 2D? Selectively formed low-dimensional perovskitoids based on chiral organic cation to passivate perovskite solar cells

Stabilisation of Inorganic Perovskite Solar Cells with A 2d Dion‐Jacobson Passivating Layer