Abstract:Formation of a two-dimensional (2D) perovskite layer on the top of three-dimensional (3D) perovskite has been demonstrated to be effective in reducing interfacial charge recombination and improving the performance and stability of perovskite solar cells (PSCs). However, it is difficult to fabricate 2D/3D perovskite heterojunction with accurate composition and structure through only solution process, and the location of 2D perovskite is also difficult to regulated owing to the uncontrolled cation exchange between organic constituents, which results in mismatched energy level arrangements. Herein, a 2D perovskite with a spacer cation of 1, 4-dimethylphenylene ammonium is grown on 3D perovskite film by the solid-state heat-pressure method. The relevant growth process, light absorption ability, energy level regulation and stability property of the samples are systematically investigated. A broad range of experimental characterizations exhibit that the introduction of 2D perovskite improve the energy level alignment with adjacent carbon electrode and enhance the hydrophobic property of the perovskite sample. As a result, a champion power conversion efficiency (PCE) of 15.63% is achieved for the carbon-based hole-transport-layer-free PSCs based on 2D/3D heterojunction, which is higher than that of 11.88% for the control 3D device. Simultaneously, the improved device retains 90% of initial performance after aging for 1000 h in ambient conditions. The present work opens a new avenue for designing 2D/3D perovskite heterojunction and improve the performance and stability of PSCs.

Fully solution-processed phase-pure 3D/2D perovskite bilayer heterojunctions

Precise modulation strategies of 2D/3D perovskite heterojunctions in efficient and stable solar cells

Tailoring Phase Purity in the 2D/3D Perovskite Heterostructures Using Lattice Mismatch

Precrystallized‐Heterojunction Strategy on Precursor Solution Enables High‐Performance Semitransparent Perovskite Solar Cells

Deterministic fabrication of 3D/2D perovskite bilayer stacks for durable and efficient solar cells

A 2D/3D heterojunction engineering for carbon-based hole-transport-layer-free perovskite solar cells

Controlled Dion-Jacobson Low-Dimensional Surface Phase Enables Highly Efficient and Stable Perovskite Solar Cells

Heterojunction formed via 3D-to-2D perovskite conversion for photostable wide-bandgap perovskite solar cells

Intact 2D/3D halide junction perovskite solar cells via solid-phase in-plane growth

Bilayer 2D-3D Perovskite Heterostructures for Efficient and Stable Solar Cells

Stable and Efficient 3D-2D Perovskite-Perovskite Planar Heterojunction Solar Cell without Organic Hole Transport Layer

Two birds with one stone: Simultaneous realization of constructed 3D/2D heterojunction and p-doping of hole transport layer for highly efficient and stable perovskite solar cells

Preheating-assisted deposition of solution-processed perovskite layer for an efficiency-improved inverted planar composite heterojunction solar cell

Nanoscale phase management of the 2D/3D heterostructure toward efficient perovskite solar cells

Leveraging Dion–Jacobson Interface Hierarchies for Defect Alleviation in High-Efficiency and Durable Perovskite Solar Cells

Holistic energy landscape management in 2D/3D heterojunction via molecular engineering for efficient perovskite solar cells

Solution‐Phase Epitaxial Growth of Perovskite Films on 2D Material Flakes for High‐Performance Solar Cells

Governing the dispersion of quasi-2D perovskite phases toward efficient and stable perovskite solar cells

Suppressing halide phase segregation in wide-bandgap perovskite film by co-doping strategy for high-performance and stable perovskite solar cells

Surface Reconstruction and In Situ Formation of 2D Layer for Efficient and Stable 2D/3D Perovskite Solar Cells

Buried-Interface Engineering of Conformal 2D/3D Perovskite Heterojunction for Efficient Perovskite/Silicon Tandem Solar Cells on Industrially Textured Silicon