Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Assessing economic trade-off for advances in amine-based post-combustion capture technology

Reducing Aerosol and Ammonia Emission in Post-Combustion CO2 Capture: Additives As Key Solutions

Comparative Analysis of the Efficiency Penalty in Power Plants of Different Amine-Based Solvents for CO2 Capture

Comparative Techno-Economic Analysis of CO2 Capture Processes Using Blended Amines

Cost-effective carbon-based amine adsorbents for carbon capture: Equilibrium, kinetics and selectivity

New Approach with Universal Applicability of Evaluating the Heat Requirements in Solvent Regeneration Process for Post-Combustion CO2 Capture

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

Industrial test of post combustion CO2 capture by reactive absorption with two new solvents in natural gas power plant

The Advances of Post-combustion CO2 Capture with Chemical Solvents: Review and Guidelines

New improvement of amine-based CO2 capture processes using heat integration and optimization

Post-combustion carbon capture process modeling, simulation, and assessment of synergistic effect of solvents

Evaluation on water balance and amine emission in CO2 capture

Operability-economics trade-offs in adsorption-based CO$_2$ capture process

Techno-economic Evaluation of Post-Combustion Carbon Capture Based on Chemical Absorption for the Thermal Cracking Furnace in Ethylene Manufacturing

Intrinsic Insight of Energy-Efficiency Optimization for CO2 Capture by Amine-Based Solvent: Effect of Mass Transfer and Solvent Regeneration

Evaluating Solvent Efficiency for Carbon Capture: Comparative Analysis of Temperature, Concentration and Diffusivity Effects

Optimization of solvent properties for post-combustion CO2 capture using process simulation

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

Process Simulation and Energy Consumption for CO<SUB Align="right">2 Capture with Different Flowsheets

Experimental Study of the Absorption and Regeneration Performance of Several Candidate Solvents for Post-Combustion CO2 Capture

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process