Abstract:In this paper, the possibility of applying the electrospark alloying (ESA) method to obtain boron-containing coatings characterised by increased hardness and wear resistance is considered. A new method for producing such coatings is proposed. The method consists in applying grease containing aluminium powder and amorphous boron to the surface to be treated and subsequently processing the obtained surface using the ESA method by a graphite electrode. The microstructural analysis of the Al-C-B coatings on steel C40 showed that the surface layer consists of several zones, the number and parameters of which are determined by the energy conditions of the ESA process. Durametric studies showed that with an increase in the discharge energy influence, the microhardness values of both the upper strengthened layer and the diffusion zone increased to Wp = 0.13 J, Hµ = 6487 MPa, and Wp = 4.9 J, Hµ = 12350 MPa, respectively. The results of X-ray diffraction analysis indicate that at the discharge energies of 0.13 and 0.55 J, the phase composition of the coating is represented by solid solutions of body-centred cubic lattice (BCC) and face-centred cubic lattice (FCC). The coatings obtained at Wp = 4.9 J were characterised by the presence of intermetallics Fe4Al13 and borocementite Fe3 (CB) in addition to the solid solutions. The X-ray spectral analysis of the obtained coatings indicated that during the electrospark alloying process, the surface layers were saturated with aluminium, boron, and carbon. With increasing discharge energy, the diffusion zone increases; during the ESA process with the use of the discharge energy of 0.13 J for steel C40, the diffusion zone is 10-15 μm. When replacing a substrate made of steel C40 with the same one material but of steel C22, an increase in the thickness of the surface layer accompanied by a slight decrease in microhardness is observed as a result of processing with the use of the ESA method. There were simulated phase portraits of the Al-C-B coatings. It is shown that near the stationary points in the phase portraits, one can see either a slowing down of the evolution or a spiral twisting of the diffusion-process particle.

Electron-Beam Modification of Carbon Steel Surface

Mechanism of Laser Carbonitriding Enhancing the Wear Resistance of 45# Steel

Thermal and Diffusion Processes during Electron Beam Processing of Surfaces of Electroexplosive Alloying

Steel Surface Modification with Carbon Nanomaterial Using Concentrated Energy Flows

Modification of Structure and Properties of Surfacing of High-Speed Steel by Electron-Beam Treatment

Electron beam hardening of nanobainitic steel

Microstructure and Wear Resistance of Hot-Work Tool Steels after Electron Beam Surface Alloying with B4C and Al

Revealing working hardening behavior and substructure evolutions of ultrahigh strength and enhanced wear resistance Fe–25Mn–7Al–1C steel treated by explosion processing

Effects of laser heat treatment combined with ultrasonic impact treatment on the surface topography and hardness of carbon steel AISI 1045

The effect of ultra-fast surface hardening and strengthening on microstructure and mechanical properties of cast (9Cr–3Co–3W) heat-resistant steel

Modification of AISI 420 Steel under Repetitively Pulsed Energetic Impact on the Surface of a Powerful Ion Beam of Submillisecond Duration

Surface Nanocrystallization of C45E4 Steel by Ultrafast Electropulsing-Ultrasonic Surface Treatment

Assessment of Technological Capabilities for Forming Al-C-B System Coatings on Steel Surfaces by Electrospark Alloying Method

Surface Modification of Mild Steel by Carbon Nanotubes Reinforcement under Electron Beam Melting

Surface nanocrystallization on stainless steel with high hardness induced by electron beam direct irradiation

Structure and Abrasive Wear Resistance of Stainless-Steel Surface Layers Alloyed with Boron

Effect of laser surface hardening on a low carbon steel substrate wear and hardness

A Study on Surface Hardening and Wear Resistance of AISI 52100 Steel by Ultrasonic Nanocrystal Surface Modification and Electrolytic Plasma Surface Modification Technologies

A Novel Electropulsing Treatment to Improve the Surface Strength and Repair the Pore of Additively Manufactured Ti-6Al-4V Alloy

Surface modification of mild steel using a combination of laser and electrochemical processes

Surface Cladding of Mild Steel Coated with Ni Containing TiO2 Nanoparticles Using a High-Temperature Arc from TIG Welding