Abstract:B-containing high temperature titanium alloys were in situ fabricated successfully by casting route. The influences of heat treatment processes on the evolution of microstructures, textures, strengths, elongations and fracture characteristics at room temperature (RT) and high temperature (650 degrees C) were analyzed. Microstructure investigation revealed that TiB whiskers stimulated the dynamic recrystallization behavior. The volume fractions of primary alpha phase (V-P alpha) decreased with the increasing solution temperature, while the volume fractions of transformed beta phase (V-T beta) and widths of secondary alpha lamellas in transformed beta phase (W-S alpha) increased. The inverse pole figures (IPFs) observations illustrated nea-requiaxed alpha grains transformed to ideal equiaxed morphology after 960 degrees C solution. By the analyzation of pole figues (PFs), after alpha+beta heat treatments, the overall texture intensity increased with the increasing solution temperature, and after beta heat treatments, textures with comparatively high intensities were concentrated around various directions. The equiaxed alpha grains and lamellar alpha phase had similar main texture components. But the maximum texture intensity of lamellar alpha phase was obviously higher than that of equiaxed alpha grains. Moreover, the textures of equiaxed alpha gains and lamellar alpha phase exhibited higher similarity after 980 degrees C solution comparing with after 960 degrees C solution. Alloy after 980 degrees C solution exhibited an excellent combination of RT and 650 degrees C mechanical properties which was ascribed to the microstructure tailoring and the load-sharing effect of TiB whiskers. Fracture of alloys was due to the debonding of TiB whiskers, and the growth and coalescence of micro-voids in matrix and around the cracks of fractured TiB whiskers. (C) 2019 Elsevier B.V. All rights reserved.

TiB whisker induced variant selection in titanium matrix composites

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Room temperature tensile fracture characteristics of in situ TiBw/Ti6Al4V composites with a quasi-continuous network architecture

Tailoring A Novel Network Reinforcement Architecture Exploiting Superior Tensile Properties of in Situ Tibw/Ti Composites

Enhancing Ductility of Titanium Matrix Composites by Multimodal Α-Grains

Variant selection of α precipitates formed at β triple junctions in titanium alloy

Growth behavior and variant selection of grain boundary α in Ti6246

Effect of Cooling Rate on α Variant Selection and Microstructure Evolution in TB17 Titanium Alloy

TiB Whiskers Stimulated the Dynamic Recrystallization Behavior

Microstructure and Mechanical Properties Evolution of High-Temperature Titanium Alloys with In Situ Synthesized TiB Whiskers

A TiB whisker-reinforced titanium matrix composite with controllable orientation: A novel method and superior strengthening effect

Variant selection during α precipitation in Ti–6Al–4V under the influence of local stress – A simulation study

The "pinning" effect of in-situ TiB whiskers on the hot deformation behavior and dynamic recrystallization of (10 vol%) TiB/Ti-6Al-4V composites

Effect of cooling rate on α variant selection and microstructure evolution in a near β Ti–5Al–3Mo–3V–2Cr–2Zr–1Nb–1Fe alloy

Formation evolution and strengthening of quasi-continuous network like TiB whiskers in the in-situ TiBw/TC21 matrix composites

Morphology evolution and orientation characteristics of precipitate of ultra-high strength titanium alloy

Variant selection of massive γ subgrains and corresponding mechanical properties in Ta containing γ-TiAl-based alloys

Influence of alternate grain boundary α on the development of Widmanstätten microstructure in TC21 Ti alloy

In-situ manipulation of TiB whisker orientation and investigation of its high-temperature mechanical properties in titanium matrix composites

Variant selection of orthorhombic phase precipitation and its effect on colony side plates formation in Ti–22Al–25Nb alloy

An investigation on grain refinement mechanism of TiB2 particulate reinforced AZ91 composites and its effect on mechanical properties