Abstract:The significant disparities in physical and chemical properties between aluminum alloy and high-strength steel pose substantial challenges for conventional friction joining techniques. To address this issue, this study proposes a novel approach utilizing inertial friction welding with an interlayer to join these dissimilar materials. A CrCoNi medium entropy alloy sheet was selected as the interlayer due to its intermediate melting point, thermal conductivity, strength, and surface hardness between 6061-T6 aluminum alloy and 42CrMo steel, as well as its high element mixing entropy. These properties were deemed crucial for balancing interface heat generation and regulation the formation of intermetallic compounds. The experimental procedure involved embedding the CrCoNi sheet into the end face of the 6061-T6 aluminum alloy, followed by the application of IFW to join the aluminum alloy with 42CrMo high-strength steel. This investigation focuses on examining the effects of three distinct friction speeds (3800, 4000, and 4200 rpm) on the microstructural characteristics and mechanical properties of the regulating joints with the CrCoNi interlayer. Results demonstrate that the CrCoNi enhances the temperature at the steel-side interface through friction with 42CrMo steel and 6061-T6 aluminum, combined with adjustments in the friction sequence and duration, promoting plastic deformation. The axial transfer of heat creates a temperature gradient at the joint, enabling low-temperature welding on the aluminum side and forming a mechanical interlocking structure at the interface. The diffusion of Cr, Co, and Ni elements regulates the type and thickness of interfacial intermetallic compounds, ultimately enhancing the joint's strength. The thickness of the intermetallic compounds AlNi3, FeAl3, AlCo, and Fe2Al5 formed at the interface is less than 2 μm. A phase transformation occurred at the 42CrMo high-strength steel interface, leading to the formation of numerous needle-like martensites, which increased the Vickers hardness in the welding seam to 763.9 HV. The joint's tensile strength initially increased and then decreased with increasing friction speed, reaching a maximum of 168.7 MPa at 4000 rpm, which is more than 60% of the aluminum alloy base material's tensile strength.

Interfacial microstructure and mechanical properties of 2124 aluminum alloy reinforced by AlCoCrFeNi high entropy alloy

Macro-micro Analysis of Mechanical Properties of Al0.6CoCrFeNi High-Entropy Alloy Particle-Reinforced Al-based Composites

Modifying Element Diffusion Pathway by Transition Layer Structure in High-Entropy Alloy Particle Reinforced Cu Matrix Composites

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Interfacial Engineering Reaction Strategy of In-Situ Cr23C6/CoCrFeNi Composites with Network Structure for High Yield Strength

Microstructure and Mechanical Properties of Novel CrCoNi–Al2O3P Medium Entropy Alloy-Matrix Composites

Surface modification of aluminum alloy by incorporation of AlCoCrFeNi high entropy alloy particles via underwater friction stir processing

Microstructure and properties of FeCoNiCrAl high-entropy alloy particle-reinforced Cu-matrix composites prepared via FSP

The Design of Aluminum-Matrix Composites Reinforced with AlCoCrFeNi High-Entropy Alloy Nanoparticles by First-Principles Studies on the Properties of Interfaces

Enhanced inertia friction welding of aluminum alloy and high-strength steel using CrCoNi interlayer: Microstructural and mechanical characterization

High-entropy CoCrFeMnNi alloy/aluminide-laminated composites with enhanced quasi-static bending and dynamic compression properties

Interfacial Characteristics and Enhanced Mechanical Properties of Al0.5CoCrFeNi High-Entropy Alloy Particles Reinforced Al Matrix Composites

The Influence of Multi-Phase Intermetallic Compounds on the Microstructure and Tribological Behaviors of 6061 Al Alloy by Adding AlCoCrFeNi High-Entropy Alloy

Microstructural, Microhardness and tribological analysis of cooling-assisted friction stir processing of high-entropy alloy particles reinforced aluminum alloy surface composites

Microstructure and mechanical properties of CrMnFeCoNi high entropy alloy/Al composite with different reinforcement content

Influence of alumina whisker or nano-carbon contents on the microstructure and mechanical properties of CuZrTiAlNi refractory high entropy alloy composites

Friction stir processing of high-entropy alloy reinforced aluminum matrix composites for mechanical properties enhancement

Evolution of the interfacial microstructure in 316L/Al x CoCrFeNi composite material induced by high-velocity impact welding

Insight of novel CoCrFeMnNi-Al 2 O 3p high entropy alloy matrix composites by mechanical alloying and spark plasma sintering

Study on strength and toughness of FeCoCrNiAlx high entropy alloy

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion