Abstract:The results of a study of the influence of the introduction of powders of intermetallic compounds of various compositions obtained by self-propagating high-temperature synthesis (SHS) with preliminary mechanical activation on the structure, mechanical, and tribological properties of sintered bronze are presented. It was found that the introduction of 0.2–0.5 wt % of nickel and titanium aluminides, both single-phase and two-phase, leads to an increase in the density and strength of sintered bronze; maximum strength is achieved with the introduction of 0.2 wt % aluminides. The dependence of the hardness of powder bronze on the amount and composition of the intermetallic compound differs from the dependence of strength; with the introduction of single-phase intermetallic compounds, the hardness increases with increasing additive content, and with two-phase intermetallic compounds it decreases. It has been shown that the introduction of aluminides ensures a refinement of the structure of the bronze during sintering, and at an additive content of 1 wt %, an increase in the amount of eutectoid (α + δ). The introduction of aluminides also has a positive effect on the tribological properties of sintered bronze. With the introduction of 0.5 wt % two-phase nickel aluminide and 0.2 wt % single-phase titanium aluminide, the seizure pressure and wear resistance increase by 2.8 times and 3.5 times, respectively. Adding 0.5 wt % of single-phase nickel, titanium, and iron aluminides allows reducing the friction coefficient to 0.009–0.011, and two-phase iron aluminide to 0.005. The introduction of iron aluminides most effectively increases the tribological properties of sintered bronze, so the seizure pressure increases to 10 MPa and wear resistance by almost 10 times. Aluminides help reduce the relief of the friction surface during adhesive wear of sintered bronze and the formation of microlacunae, which are additional reservoirs for lubrication. The smoothest friction surface and a higher content of microlacunae are observed in samples made of powder bronze with the addition of single-phase iron aluminide.

The Preparation and Properties of Thick Bronze Coating Using Friction-Assisted Jet Electrodeposition

A Comparative Study of Interface Characteristics and Properties of Bronze Coatings on Steel by Plasma Arc and Cold Metal Transition Deposition

Simulation and experimental research on nickel-based coating prepared by jet electrodeposition at different scanning speeds

Preparation and characterization of Ni-P-Al2O3-PTFE nanocomposite coatings by unidirectional jet electrodeposition

Study of Aluminum Bronze Coating by Cold Spray Process

Preparation of Bronze (CuSn10) Parts by Material Extrusion Process Using Paraffin-Based Binder

Preparation of tubing inner surface reinforced layer by inert anode assisted jet electrodeposition

Effects of deposition current density, time and scanning velocity on scanning jet electrodeposition of Ni-Co alloy coating

On the Features of Composite Coating, Based on Nickel Alloy and Aluminum–Iron Bronze, Processed by Direct Metal Deposition

Tailoring α/β-Brass coating on steel via one-bath co-deposition: Influence of current density and electrolyte composition in pyrophosphate system

Fabrication of robust hierarchical micro/nanostructures on tin-bronze substrate

A comprehensive study on the jet electrodeposition method for fabricating 3D structures with overhangs

Tin-bronze Cladding on Thin Steel Sheet by Cold Metal Transfer Arc Deposition

Preparation of multivariate multiphase composite coatings of Ni60/high aluminum bronze and its microstructure characteristics

Microstructure and properties of cold sprayed aluminum bronze coating on MBLS10A-200 magnesium-lithium alloy

Surface Finishing and Coating Parameters Impact on Additively Manufactured Binder-Jetted Steel–Bronze Composites

Optimization of Black Nickel Coatings’ Electrodeposit onto Steel

The Electrodeposition of Nanostructured Ni-TiN Composite Films

Study of single-metal multi-nanometer electrodeposition chromium layer

Influence of Ultrafine Additives of Intermetallides on the Structure, Mechanical, and Tribotechnical Properties of Sintered Tin Bronze

A novel approach of thick coating through selective jet electrodeposition process