Abstract:Directed energy deposition (DED) process can enable rapid and low-cost manufacturing of large-scale high-strength AA2219 Al-6.3 wt%Cu alloy components, displaying broad prospects for structural lightweighting in aerospace applications. However, a high tendency to prominent porosity defects and inhomogeneous layered microstructure are intrinsically present in DED-processed Al-Cu alloy, leading to significant performance degradation and anisotropy. Herein, we demonstrate a robust DED process to fabricate high-quality formed AA2219 alloy deposits, based on in-situ synthesized TiC-containing wires and an ultrasonic-frequency pulsed (UFP) arc. The effects of in-situ synthesized submicron-scale TiC particles (average diameter 0.7 ± 0.4 μm) in microstructural evolution and mechanical performance were comparatively investigated through multi-scale microstructural characterization and mechanical property measurement. The introduction of TiC particles into the as-deposited AA2219 component results in a homogeneous refined equiaxed microstructure with an average α-Al grain diameter of 23.4 ± 2.9 μm, and a dramatical elimination of porosity defects. After undergoing a T6 solution and aging treatment, the TiC-reinforced AA2219 deposit demonstrates excellent resistance against grain coarsening, porosity defects growth, and particle segregation. Moreover, the introduced TiC particles lead to a noticeably enhanced precipitation hardening behavior. A homogeneous precipitation microstructure of dispersed θ′-Al 2 Cu particles with an average diameter of 84.1 ± 34.5 nm and a high fraction of 9.8 ± 2.5 vol% was obtained in the heat-treated AA2219 deposit. Based on the as-built multiscale homogeneous microstructure, the heat-treated deposit embedded with TiC particles exhibits a synergy of unprecedented tensile strength of 501 ± 14 MPa and excellent ductility of 9.6 ± 3.3%.

Effect of micro-alloying elements on the microstructure and properties of Ti-1300 alloy fabricated by directed energy deposition

Effects of Ti Content on the Microstructure and Mechanical Properties of Al0.2CoCrFeNi2Tix High-Entropy Alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Microstructure and mechanical properties of CrFeNi high-entropy alloy reinforced by Al and Ti elements

Microstructural Modification and Mechanical Improvement of Ultrafine-Grained Ti Alloy Through Electron Wind Force: an Innovative Approach

Effects of Fe Contents on the Microstructure and Precipitate of Ti–Al–V Alloys Prepared by Direct Energy Deposition

Effects of Ti addition and annealing on microstructure and mechanical properties of CoCrFeMnNi high-entropy alloy

The microstructural evolution and enhanced mechanical properties of in-situ Ti(C, N)-reinforced CoCrFeNiTi high-entropy alloy composites fabricated via mechanical alloying and spark plasma sintering

Effect of in-situ synthesized TiC particles on microstructure and mechanical properties of directed energy deposited AA2219 Al-Cu alloy

Titanium doping levels and their effects on FeCoCrNi high-entropy alloys: From microstructure to performance

Effect of Ti Addition on the Microstructure and High-Temperature Oxidation Property of AlCoCrFeNi High-Entropy Alloy

Microstructure and mechanical properties of cold spray additive manufactured and post heat treated high-entropy alloys with mixed CoCrFeNi and Ti powders

Effect of Al addition on the microstructure and hardness of the (AlxCoCrFe)50Ni high-entropy alloy prepared by directed energy deposition technique

Effects of Elements on the Microstructure and Mechanical Properties of AlCoCrFeNiTi High-Entropy Alloys

Microstructural evolution and mechanical properties of novel nanoparticles strengthened CoCrFeNi based high entropy alloy

Effect of TiC addition on the microstructure and mechanical properties of FeCoCrNiMn high entropy alloy fabricated by selective laser melting

Influence of Al and Ti Alloying and Annealing on the Microstructure and Compressive Properties of Cr-Fe-Ni Multi-Principal Element Alloy

Study on the Microstructure and Mechanical Properties of Non-Equimolar NiCoFeAlTi High Entropy Alloy Doped with Trace Elements

Effect of Heat Treatment on Microstructure and Mechanical Properties of Direct Energy Deposited AlCoCrFeNi2.1

Effects of Fe on microstructure and mechanical properties of CoCrNiFeAl multi-principle elements alloys

Effect of Ti on Characterization and Properties of CoCrFeNiTix High Entropy Alloy Prepared Via Electro-Deoxidization of the Metal Oxides and Vacuum Hot Pressing Sintering Process