Abstract:The evaluation of blasting vibrations primarily hinges on two physical quantities: velocity and acceleration. A significant challenge arises when attempting to reference the two types of vibration data in relation to one another, such as different types of seismometers, noise, etc., necessitating a method for their equivalent transformation. To address this, a transformation method is discussed in detail with a case study, and equations for the ratio (Ra) of the particle peak velocity (PPV) to the particle peak acceleration (PPA) are proposed. The findings are twofold: (1) The conventional data conversion processes often suffer from low accuracy due to the presence of trend terms and noise in the signal. To mitigate this, the built-in MATLAB function is used for trend term elimination, complemented by a combined approach that integrates CEEMDAN with WD/WDP for noise reduction. These significantly enhance the accuracy of the transformation. (2) This analysis reveals a positive power function correlation between Ra and the propagation distance of the blast vibrations, contrasted by a negative correlation with the maximum charge per delay. Intriguingly, the Ra values observed in pre-splitting blasting operations are consistently lower than those in bench blasting. The established Ra equations offer a rapid, direct method for assessing the transformation between the PPV and PPA, providing valuable insights for the optimization of blasting design.

What problem does this paper attempt to address?

The paper mainly addresses the following issues: ### Research Background and Objectives - **Background**: In blasting design, different buildings and structures have different control standards for the physical quantities of blasting vibrations (for example, houses, buildings, tunnels, and concrete use velocity as an indicator, while nuclear power plants and precision instruments use acceleration). Additionally, in the calculation of structural dynamic response, vibration acceleration is usually chosen as the dynamic load. - **Problem**: In the case of phased construction or design changes, there may be situations where initially only velocity or acceleration was monitored, and later another physical quantity is needed. To maximize the use of these data, a method is needed to achieve equivalent conversion between velocity and acceleration. ### Solution - **Method Discussion**: - **Eliminating Trend Items**: Use MATLAB built-in functions to remove trend items from the signal, and combine CEEMDAN with WD/WDP technology for noise reduction to improve conversion accuracy. - **Proposing Proportional Coefficient**: A formula for the ratio (Ra) of Particle Peak Velocity (PPV) to Particle Peak Acceleration (PPA) is proposed. - **Research Findings**: - The conventional data conversion process results in lower accuracy due to the presence of trend items and noise in the signal. - Analysis shows a positive power function correlation between the Ra value and the propagation distance of blasting vibration, and a negative correlation with the maximum single charge. - The Ra value observed in pre-splitting blasting operations is always lower than that in bench blasting. - **Practical Application**: The established Ra equation provides a quick and direct method to evaluate the conversion between PPV and PPA, offering valuable insights for optimizing blasting design. ### Experimental Design - **Experimental Location**: Haiyang Nuclear Power Plant (HNPP) in Shandong Province, China. - **Experimental Materials**: No. 2 rock emulsion explosives, millisecond delay detonators, and high-energy capacitor detonators were used to implement two blasting methods: pre-splitting blasting and bench blasting. - **Experimental Equipment**: TCS-B3 velocity seismograph and LC0161D acceleration seismograph were used for on-site testing. - **Experimental Batches**: The first batch included 5 blasting tests, focusing on the method of equivalent conversion between velocity and acceleration; the second batch included 32 blasting tests, used to analyze the attenuation law of velocity and acceleration and the proportional relationship between velocity amplitude and acceleration amplitude. ### Conclusion Through a series of on-site blasting tests, this paper explores the method of equivalent conversion between blasting vibration velocity and acceleration, and analyzes the ratio of these two physical quantities and their vibration attenuation laws. The study proposes a comprehensive time-domain and frequency-domain method to remove trend items and reduce noise, and provides the variation law of the ratio of velocity to acceleration under different blasting methods. These results provide important theoretical support and technical means for optimizing blasting design.

Study on the Equivalence Transformation between Blasting Vibration Velocity and Acceleration

Discussion on the Discreteness of the Attenuation Parameters of the Peak Particle Velocity Induced by Blasting

Vibration prediction with a method based on the absorption property of blast-induced seismic waves: A case study

Influence of Depth and Position of Vibration-Isolating Slot on Damping Effect of Blasting Vibration

Probability Distribution and Determination of Blast Loading During Structural Blast Resistant Study

Safety Evaluation and Application of Blasting Vibration Based on an Improved Hilbert–Huang Transform

STUDY OF SAFETY EVALUATION METHOD OF BLASTING VIBRATION BASED ON INPUT ENERGY

Research on vibration effect of tunnel blasting based on an improved Hilbert–Huang transform

Vibration response and evaluation system of cross-tunnel blasting

Comparison of dominant frequency attenuation of blasting vibration for different charge structures

Analysis of Energy Distribution for Digital Electronic Detonator Blasting

Experimental Investigation of the Propagation and Attenuation Rule of Blasting Vibration Wave Parameters Based on the Damage Accumulation Effect

Study on the Attenuation Parameters of Blasting Vibration Velocity in Jointed Rock Masses

Comparative study on tunnel blast-induced vibration for the underground cavern group

On the Proper Estimation of the Confidence Interval for the Design Formula of Blast-Induced Vibrations with Site Records

A Comparative Study of Delay Time Identification by Vibration Energy Analysis in Millisecond Blasting

Vibration Serviceability Analysis of Buildings Near the Area of Blasting Operation

Study of peak velocity of blasting vibration for raft foundation demolition based on MEA-BP algorithm

Propagation characteristics and prediction of blast-induced vibration on closely spaced rock tunnels

Study on Blasting Vibration Simulating Darthquake

Research on the Vibration Response of High-Rise Buildings under Blasting Load