Abstract:To reveal the deformation mechanism during tunneling in deep soft ground, triaxial unloading confining pressure tests and triaxial unloading creep tests were carried out on sandy mudstone specimens to study the dilatancy and fracturing behavior of soft rock. In the triaxial unloading confining pressure tests, the stress path and different unloading rates were considered to reflect the unloading characteristics of the excavation methods. The unloading rate effects and the rock damage evolution law are studied. The following conclusions are obtained from the results. Firstly, when the unloading rate is smooth, the peak strengths and deviatoric stress–strain curves under the unloading condition are close to those under the conventional loading condition. Secondly, the post-peak brittle characteristics are more apparent with the increasing unloading rates. Thirdly, the soft rock undergoes five deformation and failure regimes of elasticity, pre-peak unloading damage–dilatancy, post-peak brittle drop, linear strain softening and residual perfect plasticity under quasi-static smooth unloading of mechanized excavation which is mainly focused on in this study. Fourthly, the damage evolution law at the pre-peak damage–dilatancy stage follows an exponential function. Fifthly, during the post-peak stages, multistage microfractures are initiated, propagated and finally coalesced forming a shear-fragmentation band with a certain thickness, accompanied by significant volumetric dilatancy. In the triaxial unloading creep tests, multistep unloading of the confining pressure was applied, while the axial pressure was kept constant. The results show that when the deviatoric stress is larger and the experienced creep time is longer, the unloading effect and creep characteristics become more apparent accompanied with obvious lateral dilatancy, eventually leading to significant creep–dilatancy. The progressive failure with time is caused by the damage accumulating with time-dependent crack expansion, which can be called as ‘time-dependent damage and fracturing’. The reasons for the above evolution process are presented, then the deformation mechanism of soft rock is revealed. The soft rock deformation mainly consists of two parts. One part is the pre-peak damage–dilatancy and post-peak fracture–bulking produced at the excavation unloading instant. The other part is creep–dilatancy caused by time-dependent damage and fracturing in a period of time after excavation. The above-mentioned results of damage, dilatancy and fractures evolution process are in good agreement with the in situ monitoring results and previous studies about the surrounding rock convergence, fracturing and EDZ (excavation damaged zone) development.

Dilatancy and Multi-Scale failure characteristics of a foliated rock under triaxial confinement unloading conditions

Physical Model Test and Application of 3D Printing Rock-Like Specimens to Laminated Rock Tunnels

Influences of foliation orientation and lateral stress difference on the deformation and fracturing of a thin-layered rock around underground excavations: insight from multi-axial loading tests

An Experimental Investigation on the Foliation Strike-Angle Effect of Layered Hard Rock under Engineering Triaxial Stress Path

Experimental Study on the Dilatancy and Fracturing Behavior of Soft Rock Under Unloading Conditions

Role of foliation occurrence and stress orientation on asymmetric failure in foliated rock tunnel: Insight from numerical simulation

Brittle rock mass failure in deep tunnels: The role of infilled structural plane with varying dip angles

Buckling Failure Mechanism of a Rock Plate Under Multi-directional Constraints

Large Deformation Failure Characteristics and Control Measures for Squeezing Tunnels with Steeply Inclined and Layered Rock in Strong and Active Fault Zones: A Case Study

Time-dependent squeezing deformation mechanism of tunnels in layered soft-rock stratum under high geo-stress

Evolution of Deformation Failure and Energy of Siltite and Significant Shear Fracture Structure Under Cyclic Loading

True triaxial stresses mobilizing dilatant fracturing and engineering failure of hard rocks

Tunnel failure mechanism during loading and unloading processes through physical model testing and DEM simulation

Mechanical behavior and tension-shear failure mechanism of fractured rock mass under uniaxial condition

Influences of Schistosity Structure and Differential Stress on Failure and Strength Behaviors of an Anisotropic Foliated Rock Under True Triaxial Compression

Deformation Behaviour and Damage Evolution of Carbonaceous Phyllite under Cyclic Triaxial Loading

Transversely isotropic creep characteristics and damage mechanism of layered phyllite under uniaxial compression creep test and its application

Experimental Study on Rock Strength and Deformation Characteristics Under Triaxial Cyclic Loading and Unloading Conditions

Triaxial Creep Mechanical Behaviors and Creep Damage Model of Dolomitic Limestone Material under Multi-Stage Incremental Loading

Study the anisotropic behavior of layered surrounding rock based on 3D FDEM method

Experimental Investigation of Laws during Deformation of Circular Roadway in 10° Inclined Layered Rock