Abstract:The Bi 2 Sr 2 CaCu 2 O x (Bi-2212) precursor powder has been successfully synthesized using the spray pyrolysis method, and the powder has also been made into high critical current density Bi-2212/Ag-alloy wire with 666 filaments through the oxide-powder-in-tube (PIT) and the partial-melt processing (PMP). The advantage of low segregation was found in the spray pyrolysis precursor powder due to the gas-film-barrier high-temperature calcination for the micro-sized atomized solution droplets during the spray pyrolysis process. The droplets are instantly transformed into nearly nano-sized spherical oxide powder, and the liquid phase segregation could only appear inside each of these powder spheres during the process. And the elemental content and elemental distribution in each droplet are perfectly uniform, improving the homogeneity of the final oxide powder. In conventional precursor powders that have only undergone a solid phase sintering, the liquid phase flows between the powders, resulting in severe segregation. As the segregation phenomenon was almost avoided, the content of the Bi 2 Sr 2 CuO x (Bi-2201) phase and (Sr, Ca) x Cu y O z (alkaline earth cuprates, AEC) phase in the precursor powder decreased, leading to the enhancement of the Bi-2212 content in the precursor powder and the conductive characteristics of the wire. The superconducting critical transition temperature T c of the final wire is 90.53 K, and the Δ T c value is only 0.08 K. The wire has a small Δ T c value, further indicating the higher purity of the superconducting sample. The critical current density ( J c ) of the Bi-2212 wire reaches 283 A/mm 2 at 65 K in self-field, which is higher than that of the wire reported in the literature. After high-pressure heat treatment, the highest J e and the highest J c of the wires reach 538 A/mm 2 and 2987 A/mm 2 at 4.2 K & 12T. It indicated that the spray pyrolysis method would be a candidate method for preparing high-performance Bi-2212 wire.

Development of Multi-Filament Textured-Powder Bi-2212/Ag wire with enhanced LAR

New concept for the development of Bi-2212 wires for high field applications

Development of persistent joints for superconducting Bi-2212 coils

Progress and Current Status in Research on Nanostructured Cu-Ag Microcomposites for Conductor Wires

Groove-rolling as an alternative process to fabricate Bi-2212 wires for practical applications

Fabrication and Properties of Multifilamentary MgB2 Wires by In-Situ Powder-in-tube Process

Improving Bi-2212 multi-filament wire quality and superconductivity by cryogenic drawing

Microstructure and Critical Current Density of Bi-2212 Single- and Multi-filamentary Wires with Overpressure Heat Treatment Processing

Large critical current density improvement in Bi-2212 wires through groove-rolling process

Development of a persistent superconducting joint between Bi-2212/Ag-alloy multifilamentary round wires

Role of internal gases and creep of Ag in controlling the critical current density of Ag-sheathed Bi2Sr2CaCu2Ox wires

Improvement of plastic deformation property and current carrying capacity of Bi2212 wires through low oxygen partial pressure post-annealing of precursor

Scale-Up of Silver–Copper Composite Wires by Spark Plasma Sintering and Room Temperature Wire-Drawing for Use in 100 T Triple Coil at LNCMI

Preparation of high-performance high temperature superconducting Bi-2212 wires by the spray pyrolysis powder

Evidence for length-dependent wire expansion, filament dedensification and consequent degradation of critical current density in Ag-alloy sheathed Bi-2212 wires

Performance and Microstructure of Bi-2212 Wire under Different OverPressures Heat-treatment

Fabrication of Bi-System High Temperature Superconducting Powder

Critical current density improvement by intermediate deformation for the fabrication of Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ /Ag round wires

Microstructure and properties of nanofilament Cu-Nb and Cu-Ag composites

Development of Powder-in-Tube Processed Iron Pnictide Wires and Tapes

Design Strategy to Simultaneously Enhance Electrical Conductivity and Strength: Cold-Drawn Copper-Based Composite Wire with In-Situ Graphene