Abstract:Background: Fetoscopic spina bifida repair is increasingly being practiced, but limited skill acquisition poses a barrier to widespread adoption. Extensive training in relevant models, including both ex vivo and in vivo models may help. To address this, a synthetic training model that is affordable, realistic, and that allows skill analysis would be useful. Objective: This study aimed to create a high-fidelity model for training in the essential neurosurgical steps of fetoscopic spina bifida repair using synthetic materials. In addition, we aimed to obtain a cheap and easily reproducible model. Study design: We developed a 3-layered, silicon-based model that resemble the anatomic layers of a typical myelomeningocele lesion. It allows for filling of the cyst with fluid and conducting a water tightness test after repair. A compliant silicon ball mimics the uterine cavity and is fixed to a solid 3-dimensional printed base. The fetal back with the lesion (single-use) is placed inside the uterine ball, which is reusable and repairable to allow for practicing port insertion and fixation multiple times. Following cannula insertion, the uterus is insufflated and a clinical fetoscopic or robotic or prototype instruments can be used. Three skilled endoscopic surgeons each did 6 simulated fetoscopic repairs using the surgical steps of an open repair. The primary outcome was surgical success, which was determined by water tightness of the repair, operation time <180 minutes and an Objective Structured Assessment of Technical Skills score of ≥18 of 25. Skill retention was measured using a competence cumulative sum analysis of a composite binary outcome of surgical success. Secondary outcomes were cost and fabrication time of the model. Results: We made a model that can be used to simulate the neurosurgical steps of spina bifida repair, including anatomic details, port insertion, placode release and descent, undermining of skin and muscular layer, and endoscopic suturing. The model was made using reusable 3-dimensional printed molds and easily accessible materials. The 1-time startup cost was €211, and each single-use, simulated myelomeningocele lesion cost €9.5 in materials and 50 minutes of working time. Two skilled endoscopic surgeons performed 6 simulated, 3-port fetoscopic repairs, whereas a third used a Da Vinci surgical robot. Operation times decreased by more than 30% from the first to the last trial. Six experiments per surgeon did not show an obvious Objective Structured Assessment of Technical Skills score improvement. Competence cumulative sum analysis confirmed competency for each surgeon. Conclusion: This high-fidelity, low-cost spina bifida model allows simulated dissection and closure of a myelomeningocele lesion. VIDEO ABSTRACT.

Evaluating the efficacy of a cost-effective, fully three-dimensional-printed vertebra model for endoscopic spine surgery training for neurosurgical residents

Low-Cost 3D Models for Cervical Spine Tumor Removal Training for Neurosurgery Residents

Applying 3-Dimensional Printing and Modeling for Preoperative Reconstruction and Instrumentation Placement Planning in Complex Deformity Surgery

Reducing the learning curve of interlaminar full-endoscopic discectomy: mushroom model-simulation training

Feasibility of High-Fidelity Simulator Models for Minimally Invasive Spine Surgery in a Resource-Limited Setting: Experience From East Africa

Patient-Tailored 3D-Printing Models in the Subspecialty Training of Spinal Tumors: A Comparative Study and Questionnaire Survey.

Investigation of a three‐dimensional printed dynamic cervical spine model for anatomy and physiology education

Application of 3D printing technology in the teaching and training of spine surgery

Three-Dimensional Printing in Surgical Education: An Updated Systematic Review of the Literature

High-fidelity, low-cost synthetic training model for fetoscopic spina bifida repair

Evaluation of training models for intraventricular neuroendoscopy

Advancing 3-Dimensional Printed Burr Hole and Craniotomy Models for Neurosurgical Simulation Through Multimaterial Methods

3D Printing Model of a Patient's Specific Lumbar Vertebra

Personalized biomodel of the cervical spine for laboratory laminoplasty training

A Practical 3D-Printed Model for Training of Endoscopic and Exoscopic Intracerebral Hematoma Surgery with a Tubular Retractor

Recent advances of 3D-printing in spine surgery

Dural Closure Training With Prototyped Model

Step-by-Step Implementation of Three-Dimensional Print Technology in Preoperative Neurosurgery Planning

Quantitative assessment and objective improvement of the accuracy of neurosurgical planning through digital patient-specific 3D models

Complicated Postoperative Flat Back Deformity Correction With the Aid of Virtual and 3D Printed Anatomical Models: Case Report

3D-Printed Disease Models for Neurosurgical Planning, Simulation, and Training