Abstract:The cavitation behavior of polypropylene-silica (PP-silica) and high density polyethylene-silica (HDPE-silica) composites with varying silica content during uniaxial tension was investigated via in situ X-ray techniques. The introduction of silica was found to significantly influence the mechanical properties of the materials. Small-angle X-ray scattering (SAXS) was employed to determine the cavitation onset strain and to observe the evolution of cavity structures. Through model fitting, the size evolution of nanoscale cavities at the onset of cavitation was quantitatively characterized. Scanning electron microscopy (SEM) was utilized to examine the morphology before and after stretching, revealing that cavity structures primarily resulted from internal defects in the polymer matrix and interfacial debonding between silica and the polymer. The long axis of the nanoscale cavities at the onset of cavitation was perpendicular to the tensile direction, and further deformation led to the coalescence into micron-sized cavities with the long axis parallel to the tensile direction. Wide-angle X-ray scattering (WAXS) was used to characterize the microscale deformation process of crystals, showing that during stretching, the lamellae reoriented with the angle between their normal direction and the tensile direction gradually decreasing. Several sets of transition strains representing the plastic deformation were used to compare the microscale and macroscale deformation, elucidating the sequence and differentiation between crystal plastic deformation, cavitation, and yield in the two polymer materials. Intriguingly, both PP-silica and HDPE-silica composites exhibited optimal silica additions and initial structural parameters for regulating cavitation behavior. These findings offer significant guidance for the control of internal structures in porous separators in industrial production.

Nanoscale Structures of Tough Microparticle-Based Films Investigated by Synchrotron X-Ray Scattering and All-Atom Molecular-Dynamics Simulation

Tensile Performance of Polymer Nanocomposites with Randomly Dispersed Carbon Nanothreads

Sliding Behaviour of Carbon Nanothread Within a Bundle Embedded in Polymer Matrix

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Inhomogeneous Deformation of Microcrystalline Region in Isotactic Polypropylene Film Revealed by A Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress

Deformation Behavior of Microparticle-Based Polymer Films Visualized by AFM Equipped with a Stretching Device

A Synergistic Interfacial and Topological Strategy for Reinforcing Aramid Nanofiber Films.

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

Bio-inspired Clay Nanosheets/polymer Matrix/mineral Nanofibers Ternary Composite Films with Optimal Balance of Strength and Toughness

Effect of Interfacial Local Conformation of Polymer Chains on Adhesion Strength

Acrylonitrile-Styrene-Acrylate Particles with Different Microstructure for Improving the Toughness of Poly(styrene-co-acrylonitrile) Resin

Probing the Effects of Nanoscale Architecture on the Mechanical Properties of Hexagonal Silica/Polymer Composite Thin Films

Higher order structures and toughening mechanisms for simultaneously polymerized polymethacrylate/polyurethane

Dual Nanofillers Reinforced Polymer-Inorganic Nanocomposite Film with Enhanced Mechanical Properties

Control of nano-cavitation in semi-crystalline polymer nanocomposites during uniaxial tension: In situ synchrotron X-ray study

Enhancement of Modulus, Strength, and Toughness in Poly(methyl methacrylate)-Based Composites by the Incorporation of Poly(methyl methacrylate)-Functionalized Nanotubes

Tunable Affinity and Molecular Architecture Lead to Diverse Self-Assembled Supramolecular Structures in Thin Films.

Nanoconfinement Controls Mechanical Properties of Elastomeric Thin Films

Preparation and Mechanical Properties of UV-Curable Epoxy Acrylate/Modified Aramid Nanofiber Nanocomposite Films

Visualization of Structural Deformation of Polymer Additives in Oil Under High Shear Flow

High aspect ratio cellulose nanofibrils with low crystallinity for strong and tough films