Abstract:Skull reconstruction using cranial implants is often required for repairing skull defects caused due to trauma, diseases, or malignancy to protect intracranial structures. For relieving Intracranial Pressure (ICP) surgeons restore cranial defects either using natural bones or fabricated custom cranial implants. With the increase in Traumatic Brain Injuries (TBI) and challenges faced by TBI patients to regain normalcy, it is imperative to analyse the mechanical behaviour of skull-implant assemblies under some Head Injury Criteria (HIC). Medical grade materials including Titanium Alloys (Ti-6Al-4V) and Polyether-ether-ketone (PEEK) are used by fabricating Patient-Specific Implants (PSI) manufactured using 3D imaging, modelling and printing techniques. 3D technologies are preferred over conventional manufacturing methods, as they enable fabrication of custom shapes, sizes and properties for these PSI. For an effective attachment of PSI with a defective skull, a stable joint and plate arrangement as fixture plates is necessary at their interface. These fixtures can have variable numbers, design shapes, materials and location arrangements. This paper presents the Finite Element Method/Analysis (FEM/FEA) study of PSI attached to a defected skull for reconstruction, with linear shaped fixture configuration, when subjected to an external dynamic loading at 5 m/s, strain rate of 10s-1 to 243s-1 and ICP of 15mm Hg from three sides of the skull faces. Three different materials as Neoprene (soft), Concrete (medium rigid) and E-Glass (highly rigid) have been used, in the form of a rectangular thin cuboidal wall structure, at an angle of 45° with the skull face. Four linear shaped fixture plates which were simplest to design, were used to attach the PSI-skull assembly, to ensure that weight of the PSI-fixation assembly on the patient remains minimal, overall assembly has symmetrical fixations and efforts required by a surgeon for fitment of these plates remain minimal. Placement of these fixture plates has been optimized to encompass the complete PSI-skull interface section, due to which the stresses within all the assembly components (PSI, fixture plate and skull) reduced by nearly 2.5 times than the initial design and remained within yielding limits, thereby, averting any failure under heavy external dynamic loading.

Validation of Low Cost Patient Specific Implant Design Using Finite Element Analysis (FEA) for Reconstruction of Segmental Mandibular Defects: A Case Report and Literature Review

Application of CAD/CAM Techniques in Mandible Large-Scale Defect and Reconstruction with Vascularized Fibular Bone Graft

Design Criteria for Patient-specific Mandibular Continuity Defect Reconstructed Implant with Lightweight Structure using Weighted Topology Optimization and Validated with Biomechanical Fatigue Testing

Finite Element Assessment of a Novel Patient‐Specific Mandibular Implant for Severely Atrophic Ridge

A 3-Dimensional finite element analysis of patient-specific implant (with strut abutments) interface on stress concentration on the implant and surrounding bone in bilateral maxillary deformities

Biomechanical assessment of mandibular fracture fixation using finite element analysis validated by polymeric mandible mechanical testing

The use of modified 3D-printed reconstruction plates in mandible segmental defect rehabilitation: a case report

Mandibular reconstruction system reliability analysis using probabilistic finite element method

Biomechanical Behavior of the Three-Dimensionally Printed Surgical Plates for Mandibular Defect Reconstruction: a Finite Element Analysis

Additive manufacturing of reconstruction devices for maxillofacial surgery: design and accuracy assessment of a mandibular plate prototype

Feasibility of Customised Polymethyl Methacrylate Implants Fabricated Using 3D Printed Flexible Moulds for Correction of Facial Skeletal Deformities

An in-vitro evaluation of a novel design of miniplate for fixation of fracture segments in the transition zone of parasymphysis-body region of mandible using finite element analysis

In-House, Open-Source 3D-Software-Based, CAD/CAM-Planned Mandibular Reconstructions in 20 Consecutive Free Fibula Flap Cases: An Explorative Cross-Sectional Study With Three-Dimensional Performance Analysis

A Patient Specific Biomechanical Analysis of Custom Root Analogue Implant Designs on Alveolar Bone Stress: A Finite Element Study

Use of customized 3-dimensional printed mandibular prostheses with a dental implant pressure-reducing device in mandibular body defect: A finite element study performing multiresponse surface methodology

Biomechanical finite element analysis of short-implant-supported, 3-unit, fixed CAD/CAM prostheses in the posterior mandible

Biomechanical analysis of a cranial Patient Specific Implant on the interface with the bone using the Finite Element Method

A Novel Conceptual Design of a Biomimetic Oral Implant and Its Biomechanical Effect on the Repairment of a Large Mandibular Defect

Experimental validation of finite element simulation of a new custom-designed fixation plate to treat mandibular angle fracture

The role of patient specific implants in the oral and maxillofacial region

Mechanical behaviour of reconstructed defected skull with custom PEEK implant and Titanium fixture plates under dynamic loading conditions using FEM