Abstract:Purpose: To evaluate interfacial three-dimensional adaptation and internal voids of different flowable materials before and after cyclic fatigue in a simulated deep-margin elevation scenario. Methods: Eighty (n = 80) extracted premolars were selected and two Class II cavities were prepared. The mesial one with cervical margin 1 mm above the cementum-enamel junction (CEJ) and the distal one with cervical margin 1 mm below the CEJ. After performing adhesive procedures, specimens were divided into four groups according to the employed materials for 2 mm horizontal deep-margin relocation: nanohybrid composite (Clearfil ES2, Kuraray); conventional viscosity flowable composite (Tetric Flow, Ivoclar); medium viscosity flowable composite (Majesty ES2 Low Flow, Kuraray); high viscosity flowable composite (Majesty ES2 Super Low Flow, Kuraray). All restorations were finalized by oblique layering with nanohybrid composite (Clearfil ES2, Kuraray). To reveal interfacial and internal gap progression, specimens were scanned with a micro-CT (SkyScan 1172), before and after 500,000 cycles of mechanical chewing simulation (50 N, 1 Hz). Data were imported into Mimics software after smoothing and region growing. Only the 2 mm margin relocation volumes were considered. Obtained masks were analyzed for noise removal and volume calculation. At baseline, interfacial gap progression and internal voids, expressed in mm3, were collected and statistically analyzed with two-way ANOVA (α 0.05) for the variables substrate and restorative materials followed by Tukey post-hoc test. An additional two-way ANOVA test, followed by Tukey post-hoc test, was performed to evaluate variation in interfacial gap progression after mechanical aging. Results: At baseline, the ANOVA test showed a significant difference for the variable restorative materials (p = 0.01). More specifically, the Tukey post-hoc test revealed that the highly filled medium viscosity composite performed better than the conventional viscosity composite at baseline for the interfacial gap. The internal voids ANOVA test at baseline reported no significant differences for the variable tested. Analysis of variance for internal gap progression after thermocycling showed no differences for both substrate and restorative material employed. Conclusions: Highly filled medium viscosity composite performed significantly better than the conventional viscosity flowable composite for what concern baseline interfacial gaps. Artificial aging with a chewing simulator and thermocycling did not affect interfacial gap progression on enamel and dentin. The tested restorative materials performed equally after aging.

Letter by Debruyne Regarding Article, "Targets and End Points in Cardiac Autonomic Denervation Procedures".

Relative wear of flowable and highly filled composite

Flexural Properties, Wear Resistance, and Microstructural Analysis of Highly Filled Flowable Resin Composites.

Comparison of Flexural Strength and Wear of Injectable, Flowable and Paste Composite Resins

Three-Dimensional Internal Voids and Marginal Adaptation in Deep Margin Elevation Technique: Efficiency of Highly Filled Flowable Composites

Effects of the culture media optimization on pectinase production by Enterobacter sp. PSTB-1

[Surface Roughness and Gloss of Novel Flowable Composites after Polishing and Simulated Brushing Wear].

Effect of acidic media on surface characteristics of highly filled flowable resin‐based composites: An in vitro study

Simulated oral wear of packable composites

An In Vitro Investigation Of Wear Resistance And Hardness Of Composite Resins

Wear behavior at margins of direct composite with CAD/CAM composite and enamel

[Neoplastic lesions induced in the chick by ribonucleic acid extracted from leukemic tissue (avian erythroblastosis)].

A Comparative Clinical Study of the Self-Adhering Flowable Composite Resin Vertise Flow and the Traditional Flowable Composite Resin Premise Flowable

Wear behavior of different materials used for pit and fissure sealing

Lateral and anterior view to tensor fold and supratubal recess.

Calls for independent inquiry into bombing

Wear Resistance of Bulk-fill Composite Resin Restorative Materials Polymerized under different Curing Intensities

In vitro wear of packable dental composites

Monomer conversion, microhardness, internal marginal adaptation, and shrinkage stress of bulk-fill resin composites

Topography and spatial fascicular arrangement of the human inferior alveolar nerve.

The Impact of Self-Heating on Charge Trapping in High- $k$ -Metal-Gate nFETs