Abstract:Background. The aim of this research was to carry out a comparative clinical study of a self-adhesive, light-curing composite material called Vertise Flow and a traditional flow material called Premise flowable used in combination with dedicated bonding systems. In order to standardize the clinical environment, the stability of oral hygiene (analyzed with the oral hygiene index and the approximal plaque index) was taken into consideration. Methods. The study involved 37 patients with 64 fillings. They were distributed into three groups: 22 fillings in Group I, 22 fillings in Group II and 20 fillings in Group III. In Group I (G I), Vertise Flow material was applied without the use of an etching agent or a bonding system; in Group II (G II), Premise flowable material was applied without the use of an etching agent, but with the use of the OptiBond All-In-One seventh-generation bonding system; in Group III (G III), Premise flowable material was applied after etching and treatment of the hard tooth tissues using a fifth-generation OptiBond Solo Plus bonding system. Then, at appropriate time intervals (0, i.e., right after filling and after 6, 12 and 24 months), the fillings were subjected to clinical evaluation, conducted according to the Ryge scale criteria with the use of registration by means of a fluorescent high-intensity visible light beam produced by a camera (Vista Proof). Results. The quality of fillings performed with the use of comparable materials was subjected to clinical evaluation using the Ryge scale of fillings after 6, 12, and 24 months; the examination showed significant differences between the tested materials. The Vertise Flow material used without an etching agent or a bonding system (G I) presented the weakest results with respect to marginal adaptation and smoothness among those evaluated in this study. The intensification of the degradation continued over time until the final clinical observation at 24 months. The results confirmed that the best quality was achieved with the Premise flowable material after etching and treatment of the hard tooth tissues using a fifth-generation OptiBond Solo Plus bonding system (G III) relative to others for all time points during the observation. Conclusions. The used preparation scheme and bonding system have an impact on the final quality of the composite filling. There is a need to carry out a qualitative clinical evaluation of dental restorative materials under uniform conditions using evaluation scales.

Wear behavior of different materials used for pit and fissure sealing

In vitro evaluation of wear resistance, microhardness and superficial roughness of different fissure sealants after aging

Evaluation of the wear resistance of new nanocomposite resin restorative materials

Degradation of Tooth Occlusal Fissure and Pit Sealants by Wear and Corrosion Pathways: A Short Review

Relative wear of flowable and highly filled composite

Wear behavior at margins of direct composite with CAD/CAM composite and enamel

[Micro-CT observations of the adaptation at gingival wall in Class II restorations with different dental restorative materials]

An In Vitro Investigation Of Wear Resistance And Hardness Of Composite Resins

Wear and roughness analysis of two highly filled flowable composites

Microleakage Assessment of Different Preparation Techniques and Pit and Fissure Sealants in Permanent Molars

Evaluation of Mechanical Behavior of Premolar Teeth with Fissure Sealant

Comparative evaluation of sealing ability, penetration and adaptation of a self etching pit and fissure sealant- stereomicroscopic and scanning electron microscopic analyses

Wear Resistance of Bulk-fill Composite Resin Restorative Materials Polymerized under different Curing Intensities

Protective Effects of Resin Sealant and Flowable Composite Coatings Against Erosive and Abrasive Wear of Dental Hard Tissues.

Attritional wear and abrasive surface alterations of composite resin materials in vitro

An In Vitro Study regarding the Wear of Composite Materials Following the Use of Dental Bleaching Protocols

A Comparative Clinical Study of the Self-Adhering Flowable Composite Resin Vertise Flow and the Traditional Flowable Composite Resin Premise Flowable

Sliding contact wear and subsurface damage of CAD/CAM materials against zirconia

Wear rates of regular and tempered composites

A Comparative Evaluation of the Effect of Bonding Agent on the Tensile Bond Strength of Two Pit and Fissure Sealants Using Invasive and Non-invasive Techniques: An in-vitro Study

Simulated oral wear of packable composites