Abstract:Purpose The additive manufacturing process, such as fused filament fabrication based on material extrusion, fabricates the samples layer-by-layer. The various parameters in the process significantly affect the dimensions, structure and mechanical properties of the fabricated parts. The purpose of this paper is to investigate the surface and mechanical properties that can affect the contact characteristics with other materials during tribological tests. Design/methodology/approach The investigation of 3D-printed Polyetheretherketone (PEEK) includes the measurement of dimensions, microhardness, surface roughness, surface energy and tensile strength to define material characteristics. The crystallinity is measured using an X-ray diffractometer to understand the hardness behaviour. Findings The printing parameters affect its surface roughness, hardness and crystallinity. This change in parameters such as layer thickness and infill density impacts mechanical properties such as hardness and surface roughness, which will influence the contact mechanism with the counter body during any tribological test. The change in a single parameter during the sample fabrication and the change in the surface and mechanical properties are observed. Research limitations/implications The material cost plays an important role in conducting numerous destructive tests, which is a major limitation to conducting parameter optimisation by varying more parameters. The study is limited to the as-fabricated samples rather than finished samples and without any heat treatment. Achieving optimal parameters is integral to the success of additive manufacturing, ensuring the production of components with consistent performance. Practical implications The study aims at the application of 3D-printed PEEK for bush or journal bearings that can be directly used in practice. The mechanical properties discussed in this paper can fill the gap between theory and practice. Social implications The research provides all fundamental properties, including the printing parameters and their effect on the dimensions and surface structure, which are required to understand the material and its use. The results are consistent as at least four samples were tested for tribological behaviour. The conclusion is updated as per suggestions. Originality/value The study outlines the relationship between the change in layer thickness and infill density with changes in surface energy, surface roughness, hardness and tensile strength. The deformation and adhesion during the friction test depend on these properties.

Evaluation of the Influence of Technological Parameters of Selected 3D Printing Technologies on Tribological Properties

ASSESSMENT OF TRIBOLOGICAL PROPERTIES OF POLYMERS USED IN ADDITIVE TECHNOLOGIES SLS AND PJM

Multiobjective optimization of tribological characteristics of 3D printed texture surfaces for ABS and PLA Polymers

Impact of processing defects on microstructure, surface quality, and tribological performance in 3D printed polymers

Optimization of 3D Printing Parameters for Enhanced Surface Quality and Wear Resistance

Wear and Dynamic Mechanical Analysis (DMA) of Samples Produced via Fused Deposition Modelling (FDM) 3D Printing Method

Effect of print orientation and bronze existence on tribological and mechanical properties of 3D-printed bronze/PLA composite

Investigation of tribological properties of industrial products with different patterns produced by 3D printing using polylactic acid

The Influence of 3D Printing Parameters on the Mechanical Behavior of PLA

The Influence of 3D Printing Parameters on Adhesion between Polylactic Acid (PLA) and Thermoplastic Polyurethane (TPU)

Tribological Characterisation and Modelling for the Fused Deposition Modelling of Polymeric Structures under Lubrication Conditions

Experimental Investigation on Friction Behavior of Selective Laser Sintering Processed Parts

Investigations into the Material Characteristics of Selected Plastics Manufactured Using SLA-Type Additive Methods

Mechanical and surface characterisation of additively manufactured polyetheretherketone for the tribo test

Frictional Behaviors of 3D-Printed Polylactic Acid Components With Spiral-Groove Surface Textures Under Oil Lubrication

Effect of nozzle wear on mechanical properties of 3D printed carbon fiber-reinforced polymer parts by material extrusion

Analyzing the Influence of Multimaterial 3D Printing and Postprocessing on Mechanical and Tribological Characteristics

Threshold investigation of shell thickness for enhanced mechanical and tribological performance in 3D-printed curved sandwich structures

A comprehensive review of polymer materials and selective laser sintering technology for 3D printing

Friction and Wear Behavior of 3D-Printed Inconel 718 Alloy under Dry Sliding Conditions

Multi-objective optimization of 3D printing parameters to fabricate TPU for tribological applications