Abstract:Purpose The additive manufacturing process, such as fused filament fabrication based on material extrusion, fabricates the samples layer-by-layer. The various parameters in the process significantly affect the dimensions, structure and mechanical properties of the fabricated parts. The purpose of this paper is to investigate the surface and mechanical properties that can affect the contact characteristics with other materials during tribological tests. Design/methodology/approach The investigation of 3D-printed Polyetheretherketone (PEEK) includes the measurement of dimensions, microhardness, surface roughness, surface energy and tensile strength to define material characteristics. The crystallinity is measured using an X-ray diffractometer to understand the hardness behaviour. Findings The printing parameters affect its surface roughness, hardness and crystallinity. This change in parameters such as layer thickness and infill density impacts mechanical properties such as hardness and surface roughness, which will influence the contact mechanism with the counter body during any tribological test. The change in a single parameter during the sample fabrication and the change in the surface and mechanical properties are observed. Research limitations/implications The material cost plays an important role in conducting numerous destructive tests, which is a major limitation to conducting parameter optimisation by varying more parameters. The study is limited to the as-fabricated samples rather than finished samples and without any heat treatment. Achieving optimal parameters is integral to the success of additive manufacturing, ensuring the production of components with consistent performance. Practical implications The study aims at the application of 3D-printed PEEK for bush or journal bearings that can be directly used in practice. The mechanical properties discussed in this paper can fill the gap between theory and practice. Social implications The research provides all fundamental properties, including the printing parameters and their effect on the dimensions and surface structure, which are required to understand the material and its use. The results are consistent as at least four samples were tested for tribological behaviour. The conclusion is updated as per suggestions. Originality/value The study outlines the relationship between the change in layer thickness and infill density with changes in surface energy, surface roughness, hardness and tensile strength. The deformation and adhesion during the friction test depend on these properties.

ASSESSMENT OF TRIBOLOGICAL PROPERTIES OF POLYMERS USED IN ADDITIVE TECHNOLOGIES SLS AND PJM

Evaluation of the Influence of Technological Parameters of Selected 3D Printing Technologies on Tribological Properties

Comparative Evaluation of the Tribological Properties of Polymer Materials with Similar Shore Hardness Working in Metal–Polymer Friction Systems

Experimental Investigation on Friction Behavior of Selective Laser Sintering Processed Parts

A New Approach to Optimization of the Metal-Polymer Tribological Characteristics

Tribological characteristics of polymer materials used for slide bearings

Influence of adhesive and abrasive mechanisms on the tribological behaviour of thermoplastic polymers

Selected Tribological Properties and Vibrations in the Base Resonance Zone of the Polymer Composite Used in the Aviation Industry

Evaluation of Tribological Properties of Polymer Materials Used for Sliding Bearings in Agricultural Machinery

Investigations into the Material Characteristics of Selected Plastics Manufactured Using SLA-Type Additive Methods

Investigation of tribological properties of industrial products with different patterns produced by 3D printing using polylactic acid

Multiobjective optimization of tribological characteristics of 3D printed texture surfaces for ABS and PLA Polymers

Wear and Dynamic Mechanical Analysis (DMA) of Samples Produced via Fused Deposition Modelling (FDM) 3D Printing Method

Tribological Characterisation and Modelling for the Fused Deposition Modelling of Polymeric Structures under Lubrication Conditions

Mechanical and surface characterisation of additively manufactured polyetheretherketone for the tribo test

FRICTION PROCESSES OF SELECTED POLYMERS SLIDING ON STEEL AND DURALUMIN IN A LUBRICANT ENVIRONMENT

Tribological Behavior of Reinforced PTFE Composites and Un-Reinforced Polyketone-Based Materials against Coated Steel

Abrasive Sensitivity of Engineering Polymers and a Bio-Composite under Different Abrasive Conditions

ANALYTICAL STUDY OF DURABILITY AND CONTACT CHARACTERISTICS OF METAL-POLYMER COMPOSITE SLIDING BEARINGS FOR MEANS OF TRANSPORT

Tribological Performance of Additive Manufactured PLA-Based Parts

Assessment of the Tribological Properties of the Steel/Polymer/Steel Sandwich Material LITECOR