Abstract:Due to its hydroxyl terminal groups, Poloxamer ® 407 (P407), a commercially available poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymer can be used as macrodiol for the synthesis of high molecular weight amphiphilic poly(ether urethane)s (PEUs). This work was aimed at studying the effect of P407 purification by removing PEO-PPO diblock copolymer by-products on the chemical properties of PEU polymer and the physical properties of PEU hydrogels. Removal of PEO-PPO diblock copolymers (P407_P) was found to preserve the thermo-responsiveness of resulting hydrogels, although slightly lower gelation onset temperature (T onset ) was found for P407_P (15.3°C) vs . P407 (16.7°C) hydrogels (25% w/V) as assessed through temperature ramp test. P407 and P407_P were then reacted with 1,6-diisocyanatohexane and 1,4-cyclohexanedimethanol to synthesize two different PEUs, coded as CHP407 and CHP407_P, respectively. Lower Number Average Molecular Weight ( M n ̄ ) and higher polydispersity Index (D) was measured for CHP407 ( M n ̄ : 34 kDa, D: 1.6) respect to CHP407_P ( M n ̄ : 40 kDa, D: 1.4) as a consequence of macrodiol purification. CHP407_P hydrogels formed bigger micelles (43.9 ± 4.1 nm vs . 28.7 ± 4 nm) while showed similar critical micellar temperatures (22.1°C vs . 21.6°C) respect to CHP407 formulations. Sol-to-gel transition of CHP407 and CHP407_P hydrogels was similar while CHP407_P gelation time at 37°C was longer as assessed by tube inverting test. The rheological analysis showed slightly lower T onset for CHP407_P hydrogels (15% w/V), probably due to larger micelle size, promoting micellar assembly. However, CHP407_P hydrogels showed a significantly lower critical strain than CHP407 hydrogels, as assessed by strain sweep test, suggesting their higher brittleness due to a lower density of intermicellar bridge chains. Nano-scale hydrogel characterization by Low-Field Nuclear Magnetic Resonance spectroscopy supported previous findings, showing lower spin-spin relaxation time (i.e., 1,259 ms) for CHP407_P than for CHP407 hydrogels (i.e., 1,560 ms) at 37°C, which suggested the formation of a more tightly packed network for CHP407_P than CHP407 hydrogel. Finally, lower swelling capability and resistance against dissolution were measured for CHP407_P hydrogels. Overall, the here‐reported results suggested that the heterogeneous structure in the CHP407 hydrogel network caused by the presence of diblock copolymer-based macrodiols improved PEU hydrogel properties in light of their applicability in the biomedical field.

Effect of thermal treatment on the structure and the biomedical properties of polyetherurethane film containing dipeptides of L-serine

Effect Of Polyethersulfone On The Mechanical And Rheological Properties Of Polyetherimide-Modified Epoxy Systems

Morphology and mechanical properties of poly(ether-imide)-modified polycyanurates

Biomedical Segmented Polyurethanes Based on Polyethylene Glycol, Poly(ε-Caprolactone-co-d,l-lactide), and Diurethane Diisocyanates with Uniform Hard Segment: Synthesis and Properties

Thermally Stable and Mechanically Strong Mesoporous Films of Poly(ether Imide)-Based Triblock Copolymers

Synthesis and properties of biodegradable poly(ester-urethane)s based on poly(ε-caprolactone) and aliphatic diurethane diisocyanate for long-term implant application: effect of uniform-size hard segment content

Effects of Dibenzocrown Ether and Diphenoxyethylene Diether Structural Units on the Properties of Degradable Polyhexahydrotriazine Thermosetting Resins

The in Vitro and in Vivo Stability of Poly(urethaneurea)s As Biomedical Materials

Preparation, Characterization and Degradation Characteristics of Polyanhydrides Containing Poly(Ethylene Glycol)

Dipeptide Self-assembled Hydrogels with Shear-Thinning and Instantaneous Self-healing Properties Determined by Peptide Sequences

Synthesis, Characterization and Biocompatibility of Biodegradable Elastomeric Poly(ether-ester Urethane)s Based on Poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) and Poly(ethylene Glycol) Via Melting Polymerization

A Novel Polyurethane Film for Biomedical Use

Synthesis, characterization and cell compatibility of novel poly(ester urethane)s based on poly(3-hydroxybutyrate-co-4-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) prepared by melting polymerization

Performance Study of Biodegradable Polyurethanes from Different Biodicarboxylic Acids and Their Potential Applications

Effect of PEG molecular mass and HEMA capping on the thermal, morphological, and hydrophilic properties of ısocyanate-terminated polyurethane acrylate films

Using Poloxamer® 407 as Building Block of Amphiphilic Poly(ether urethane)s: Effect of its Molecular Weight Distribution on Thermo-Sensitive Hydrogel Performances in the Perspective of Their Biomedical Application

Shape Memory Properties And Enzymatic Degradability Of Poly(Epsilon-Caprolactone)-Based Polyurethane Urea Containing Phenylalanine-Derived Chain Extender

Synthesis, phase behavior, and simulated in vitro degradation of novel HTPB-b-PEG polyurethane copolymers

Synthesis and In-vitro Blood-compatibility of Polyurethane Modified by Amino Acid

Characterization, biodegradability and blood compatibility of poly[(R)-3-hydroxybutyrate] based poly(ester-urethane)s.

Synthesis and characterization of phosphoryl-choline-capped poly(ε-caprolactone)-poly(ethylene oxide) di-block co-polymers and its surface modification on polyurethanes