Abstract:Through a series of hot compression tests on a novel powder metallurgy superalloy FGH4113A (WZ-A3), the effects of deformation temperature, strain rate and strain on the microstructure evolution were investigated. The results demonstrate that when the temperature is 1100 degrees C, the strain rate is 0.1 s(-1) and the true strain is between 0.1 and 0.7, the increase in strain is beneficial to promoting dynamic recrystallization and grain refinement. With the increase in strain, the volume fraction of gamma ' phase first decreases, then increases, and eventually remains stable. The morphology of gamma ' phase gradually becomes spherical during the thermal deformation process. Under the conditions of temperature 1100 degrees C, deformation 50% and strain rate of 0.01-1 s(-1), the increase in strain rate can improve the degree of dynamic recrystallization and refine the grains. With the increase in strain rate from 0.01-0.1 s(-1) to 1 s(-1), the adiabatic temperature rises and dislocation slip intensifies, reducing the volume fraction of gamma ' phase by about 2%. When the strain rate is 0.1 s(-1) and the deformation is 50%, the increase in deformation temperature can promote dynamic recrystallization and grain growth in the temperature range of 1070-1160 degrees C. With the deformation temperature rising to 1130 degrees C, a large quantity of gamma ' phase has dissolved, the ability to pin the grain boundary has been significantly weakened, and the average grain size has increased to 12.1 mu m. At the deformation temperature of 1100 degrees C, strain rate of 1 s(-1) and deformation of 50%, fine and uniform gamma+gamma ' dual-phase structure with the grain size above ASTM 12 can be obtained.

Deformation-induced grain boundary segregation in a powder-metallurgy ultrafine-grained MoNbTaTiV refractory high-entropy alloy

Study on mechanical alloying behavior and thermal stability of HfMoNbTaTi refractory high-entropy alloy

Microstructure evolution and composition redistribution of FeCoNiCrMn high entropy alloy under extreme plastic deformation

Investigation of the Micromechanical Behavior of a Ti68Nb7Ta3Zr4Mo18 (at.%) High-Entropy Alloy

Microstructure and elevated-temperature mechanical properties of refractory AlMo0.5NbTa0.5TiZr High Entropy Alloy fabricated by powder metallurgy

The evolution of compositional and microstructural heterogeneities in a TaMo0.5ZrTi1.5Al0.1Si0.2 high entropy alloy

Effect of Deformation Parameters on Microstructure Evolution of FGH4113A Powder Metallurgy Superalloy

Effect of deformation parameters on microstructural evolution during hot compression of Nb–V–Mo microalloyed steel

Deformation and Fracture Mechanisms of an Annealing-Tailored "bimodal" Grain-Structured Mg Alloy

Deformation-induced homogenization of the multi-phase senary high-entropy alloy MoNbTaTiVZr processed by high-pressure torsion

Frustrated metastable-to-equilibrium grain boundary structural transition in NbMoTaW due to segregation and chemical complexity

Hot deformation behavior and microstructure characterization of AlCrFe2Ni2(MoNb)0.2 high entropy alloy

Deformation mechanisms and their role in the lack of ductility in the refractory-based high entropy alloy AlMo0.5NbTa0.5TiZr

High Temperature Deformation Behavior and Microstructure Evolution of Low-Density Steel Fe30Mn11Al1C Micro-Alloyed with Nb and V

Modeling refractory high-entropy alloys with efficient machine-learned interatomic potentials: Defects and segregation

High-throughput first-principles investigation on grain boundary segregation of alloying elements in ferritic steel

Deformation induced grain boundary segregation in nanolaminated Al–Cu alloy

Grain size dependent deformation behavior of a metastable Fe40Co20Cr20Mn10Ni10 high-entropy alloy

Polymorphic transformation and elemental diffusional controlled phase spheroidization of eutectic VNbTiSi medium entropy alloy during heat treatment

Thermal deformation characteristics of AlMo0.8NbTiW0.2Zr refractory multi-principal element alloy