Abstract:Additive manufacturing (AM) of biomedical materials provides enormous opportunities to fabricate multifunctional and structurally designed frameworks for tissue engineering, such as dental implants and bone substitutes. Despite several advantages of the binder jet 3D printing technology over other AM methods, for example, no limitations in materials selection, high materials recycling efficiency, no thermal stress development, no need to support materials, and the possibility of fabrication of printing functionally graded materials, the fabrication of biomedical-grade titanium alloys with high-density, fine microstructure, and low pickup of impurities is still challenging. This work presents the effects of powder particle size and 3D printing conditions on the microstructural features and mechanical properties of Ti-6Al-4V alloy. The formation of large and inter-aggregate pores during binder jetting is demonstrated and discussed. Design and selection of particle size distribution with a mean diameter of ~20 μm and large span and positive skewness are proposed to minimize binder-induced powder aggregation and fabricate green parts with a density of 65±1% PFD (pore-free density). Dilatometric studies under a partial pressure of argon (0.1 bar) determine that sintering just above the α/β transus temperature (~980 °C) provides a high strain rate to remove pores, but high-temperature sintering (≥1250 °C) is required to attain 97% PFD. The successful fabrication of high-density Ti-6Al-4V parts (≥96% PFD) with the microstructure comparable to metal injection molding (MIM) titanium parts (≈100 μm α grains + β lattes) is demonstrated. The tensile strength and elongation values fall in the range of 880±50 MPa and 6±2% (depending on the processing condition), which is comparable with metal injection molded parts and superior to the laser powder bed fusion technology concerning ductility. The content of carbon (<0.02 wt.%) and nitrogen (0.01 wt.%) also falls in the standard region of metal injection molding. However, oxygen pickup during sintering moderately increases the oxygen content (for 30–50%) over the standard level. The concentration of interstitials entrapped in the metal is comparable to that of parts manufactured by the powder bed fusion process, but the mechanical properties are better matched with the commercial titanium alloy. The fabrication of the titanium alloy as per the ASTM F2885 standard provides an excellent opportunity for the binder jetting process to develop custom-made biomaterials.

Applying Binder Jetting Technology to 316L Stainless Steel Materials and Testing Its Mechanical and Dimensional Properties Depending on the Printing Method

A Review on Binder Jet Additive Manufacturing of 316L Stainless Steel

Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges

Metal Binder Jetting Additive Manufacturing: A Literature Review

Binder jetting additive manufacturing of 316L stainless-steel green parts with high strength and low binder content: Binder preparation and process optimization

State of the art of metal powder bonded binder jetting printing technology

Binder jetting: A review of process, materials, and methods

Optimization of Binder Jetting Using Taguchi Method

Photopolymerization of Stainless Steel 420 Metal Suspension: Printing System and Process Development of Additive Manufacturing Technology toward High-Volume Production

Removal of Stair-Step Effects in Binder Jetting Additive Manufacturing Using Grayscale and Dithering-Based Droplet Distribution

Binder Jetting Additive Manufacturing of High Porosity 316L Stainless Steel Metal Foams

Microstructural development during additive manufacturing of biomedical grade Ti-6Al-4V alloy by three-dimensional binder jetting: material aspects and mechanical properties

A Novel Additive Texturing of Stainless Steel 316L Through Binder Jetting Additive Manufacturing

Effect of Printing Orientation Angle and Heat Treatment on the Mechanical Properties and Microstructure of Binder-Jetting-Printed Parts in 17-4 PH Stainless Steel

A review on recent developments in binder jetting metal additive manufacturing: materials and process characteristics

Effect of bimodal powder on densification and mechanical properties of 316L stainless steel fabricated by binder jet 3D printing

Non-heat source forming technology of binder jetting metal powder and its post-treatment process

Powder reusability in Metal Binder Jetting

Benchmarking of Print Properties and Microstructures of 316L Stainless Steel Laser Powder Bed Fusion Prints

A review of binder jet process parameters; powder, binder, printing and sintering condition