Abstract:Background: Surface treatment of the intaglio surface of zirconia is important for bonding. However, it could affect the strength of the materials. The purpose of this study is to compare the effect of laser, etching, and air abrasion surface treatment methods to a control group on the flexural strength of three zirconia materials with two different thicknesses. (1) Methods: A total of 120 disks were divided into three groups according to the type of zirconia and the ceramic thickness. Then, according to the surface treatment method, the groups were divided into four subdivisions. The change in the microstructure of the ceramic material was investigated through Scanning Electron Microscope (EVO LS10, Carl Zeiss SMT Ltd. Oberkochen, Germany). Phase identification was performed using an X-ray diffraction device (XRD; Ultimate IV X-ray Diffractometer, Rigaku Inc., Tokyo, Japan). The flexural strength was assessed with a biaxial flexural strength test in a universal testing machine. Data were analyzed using SPSS Software (SPSS version 26.0.Armonk, NY: IBM Corp). A three-way ANOVA and a post hoc Dunnett T3 test were employed to evaluate the effect of the yttria concentration, thickness, and surface treatment on the flexural strength of zirconia (α = 0.05). (2) Results: At 0.8 mm thickness, air abrasion significantly increased the flexural strength of 3Y-TZP (1130.6 ± 171.3 MPa) and 4Y-TZP (872 ± 108.6 MPa). However, air abrasion significantly decreased the flexural strength of 5Y-TZP materials (373 ± 46.8 MPa). Laser irradiation significantly decreased the flexural strength of 5Y-TZP (347 ± 50.3 MPa), while etching significantly decreased the flexural strength of both 3Y-TZP (530 ± 48.8) and 4Y-TZP (457.1 ± 57.3). When the thickness increased to 1 mm, air abrasion continued to significantly decrease the flexural strength of 5Y-TZP materials. (3) Conclusions: There was a negative effect of surface treatment on the flexural strength at 0.8 mm thickness rather than at 1 mm thickness. Air abrasion enhances the flexural strength of 3Y-TZP and 4Y-TZP materials but significantly reduces the flexural strength of 5Y-TZP materials. Zircos-E etching and Er:YAG surface treatment methods did not significantly reduce the flexural strength of 5Y-TZP materials at 1 mm thickness and can be recommended as an alternative surface treatment for 5Y-TZP materials.

Influence of different cutting instruments and rotational speeds on heat generation and cutting efficiency when sectioning different types of zirconia

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

A Machining Science Approach to Dental Cutting of Glass Ceramics Using an Electric Handpiece and Diamond Burs

Influence of Sintering Temperatures on Material Properties and Corresponding Milling Machinability of Zirconia Ceramics

Cutting Efficiency of Diamond Grinders on Composite and Zirconia

Investigation of material removal mechanisms and ductile-brittle transition zone of zirconia ceramics sintered at various temperatures

Effect of the Intaglio Surface Treatment and Thickness of Different Types of Yttria-Stabilized Tetragonal Zirconia Polycrystalline Materials on the Flexural Strength: In-Vitro Study

Impact of the sintering parameters on the grain size, crystal phases, translucency, biaxial flexural strength, and fracture load of zirconia materials

Effect of Milling Parameters on Surface Roughness for High-Speed Milling of Pre-Sintering Zirconia

Zirconia changes after grinding and regeneration firing

Assessing the Impact of Various Decontamination Instruments on Titanium and Zirconia Dental Implants: An In Vitro Study

Effect of Grinding and Regenerative Heat Treatment on the Fracture Resistance of a Zirconia/Porcelain Veneer Interface

An Experimental Investigation on Milling Features of Fully-Sintered Zirconia Ceramics Using PCD Tools

Optimization of Machining Parameters for Milling Zirconia Ceramics by Polycrystalline Diamond Tool

Critical cutting thickness model considering subsurface damage of zirconia grinding and friction–wear performance evaluation applied in simulated oral environment

Nano-scale Mechanical Behaviors and Material Removal Mechanisms of Zirconia Ceramics Sintered at Various Temperatures

Mechanical Performance of Polymer-Infiltrated Zirconia Ceramics.

Evaluation of Polycrystalline Diamond Tools in Milling of Pre-Sintered and Fully-Sintered Zirconia Ceramics

Effect of Low-Temperature Degradation, Ph-Cycling and Simulated Tooth Brushing on Surface Roughness, Topography, and Polish Retention of Yttrium-Stabilized Tetragonal Zirconia

Effect of speed sintering process on the microstructure, flexural strength and translucency of zirconia

Effect of final temperature and heating rate on the mechanical and optical properties of a zirconia veneering ceramic