Political tolerance: how adolescents deal with dissenting groups.

P. Avery

DOI: https://doi.org/10.1002/CD.23219925605

1992-06-01

Abstract:The socialization of political tolerance is influenced by U.S. adolescents' conceptualizations of dissent and dissenters.

What problem does this paper attempt to address?

Sensitive H2 Gas Sensors Based on SnO2 Nanowires

Sihang Lu,Yuzhu Zhang,Jingyao Liu,Hua-Yao Li,Zhixiang Hu,Xie Luo,Naibo Gao,Bao Zhang,Jianjun Jiang,Aihua Zhong,Jingting Luo,Huan Liu

DOI: https://doi.org/10.1016/j.snb.2021.130334

2021-01-01

Abstract:Sensitive H-2 gas sensors are highly desirable for the prediction and early-warning of H-2 leakage. Low-dimensional nanostructures of metal oxide semiconductor emerge as promising materials candidates, but it remains a challenge to preserve the nanostructures in the real sensors. In this work, we demonstrated highly sensitive H-2 gas sensors based on porous network of SnO2 nanowires that exhibited ultrasmall diameter similar to 2 nm. Colloidal SnO2 nanowires synthesized via a solvothermal process were drop-coated onto the commercial alumina substrates, followed by in-situ annealing treatment at 350 degrees C to remove the surface ligands. The sensors exhibited sensitive response with linear dependence on the H-2 gas concentration ranging from 2 ppm to 100 ppm when operated at 250 degrees C. Typically, the sensor had a response of 13 toward 40 ppm of H-2, with the response and recovery time being 15 s and 31 s, respectively. To further improve the sensor performance, Palladium doped SnO2 nanowires were thoroughly investigated. It's shown that, the operating temperature of the sensor decreased from 250 degrees C to 150 degrees C after Pd doping, and the response and recovery time decreased to 6 s/3 s. The superb sensitivity was attributed to the enhanced gas reception, electron transport as well as utility factor owing to the network nanostructure of ultrathin SnO2 nanowires and catalytic activity of Pd, according to theoretical calculation and adsorption kinetics studies. Combined with the excellent solution processability, the colloidal SnO2 nanowires are potentially attractive for next-generation gas sensors with lower power consumption and integration with silicon-based substrates.
Pd nanoparticles decorated SnO 2 ultrathin nanosheets for highly sensitive H 2 sensor: Experimental and theoretical studies

Gaojie Li,Kai Du,Xinxin Wang,Xiaochen Wang,Boao Chen,Chuangwen Qiu,Jiaqiang Xu

DOI: https://doi.org/10.1016/j.ijhydene.2023.06.263

IF: 7.2

2023-07-12

International Journal of Hydrogen Energy

Abstract:This study is attempted to improve the hydrogen sensing performance of SnO 2 based sensors by simultaneously employing two strategies of morphology control and noble metal loading. Therefore, SnO 2 ultrathin nanosheets with thickness not exceeding 3.5 nm were successfully synthesized by a hydrothermal method and then different content of Pd nanoparticles were uniformly loaded onto SnO 2 surface by in situ reduction with ascorbic acid. The gas sensing properties demonstrated that the introduction of Pd not only altered the selectivity of the SnO 2 sensor from ethanol to hydrogen, but also significantly improved the gas sensitivity and reduced the working temperature. And the optimal 1.0%Pd/SnO 2 sensor owned the highest sensitivity (75), fastest response-recovery property (21 s/13 s) to 20 ppm of hydrogen at 220 °C, and the actual detection limit is as low as 0.1 ppm. Furthermore, 1.0%Pd/SnO 2 sensor exhibited excellent repeatability, reproducibility and acceptable anti-interference of humidity. The DFT studies suggest that the physisorption of the hydrogen molecules on the surface of SnO 2 , but chemisorption on the surface of Pd/SnO 2 . The improved H 2 sensing performance of Pd/SnO 2 sensor attributes its ultrathin thickness of SnO 2 and catalytic dissociation of Pd to O 2 and H 2 .

energy & fuels,electrochemistry,chemistry, physical
Ultra-large Sn3O4 nanosheets with Sn2+ defect for highly efficient hydrogen sensing

Yuyang Liu,Shiqi Chen,Bing Xiao,Jifeng Chu,Hongkang Wang,Yukun Chen,Tianhao Yao,Aijun Yang,Xiaogang Han,Mingzhe Rong,Xiaohua Wang

DOI: https://doi.org/10.1016/j.snb.2023.135025

2024-02-01

Abstract:Hydrogen (H2) is the cleanest energy but also dangerous, thus the real-time detection of H2 leakage is crucially important. Herein, we develop ultra-large micro-sized Sn3O4 nanosheet hierarchies via a facile hydrothermal method using polyvinyl pyrrolidone as a regulating agent. Structural analyses reveal the as-prepared Sn3O4 nanosheets are single-crystalline with {010}-facet exposure and Sn2+-deficiency. When examined as gas sensing materials, the {010}-faceted Sn2+-deficient Sn3O4 nanosheets demonstrate highly efficient H2 sensing with excellent selectivity/response (two times higher than those for NO2, SO2, H2S, and H2O) and stability upon long-term testing (over 37 days). The sensor displays fast response /recovery times of 9.4/24 s to 10 ppm H2 at a low working temperature of 150 °C, and even well responds to 50 ppb H2 with a theoretical limit of detection (LOD) of 0.54 ppb. The excellent H2 sensing performance of the Sn3O4 nanosheets has been verified by the first-principle calculation based on density functional theory (DFT), suggesting that the Sn2+-deficient {010} surface of Sn3O4 provides abundant adsorption sites for hydrogen molecules. Moreover, we demonstrate the practical application of Sn3O4 sensor embedded into a miniaturized deployable module, which realizes the real-time on-line H2 monitoring with excellent repeatability and selectivity for long-term operation.

chemistry, analytical,electrochemistry,instruments & instrumentation
Ultrasensitive and Wide-Range Flexible Hydrogen Sensor Based on Pd Nanoparticles Decorated Ultrathin SnO2 Film

Qiang Ren,Xin-Yue Zhang,Ji-An Chen,Jia-Bin Fang,Tao-Qing Zi,Lin Zhu,Chang Liu,Min Han,Yan-Qiang Cao,Ai-Dong Li

DOI: https://doi.org/10.1002/aelm.202201047

IF: 6.2

2023-01-01

Advanced Electronic Materials

Abstract:Highly sensitive and reliable hydrogen detection is prerequisite for the large-scale implementation of green energy hydrogen. It remains a tough challenge to get a highly selective H-2 sensor to low concentration H-2 gas with low working temperature. In this work, high performance flexible hydrogen sensor using ultrathin SnO2 film decorated by Pd nanoparticles (NPs) on polyimide (PI) was developed based on versatile atomic layer deposition (ALD) and cluster beam deposition (CBD). The influence of Pd NPs loading amount and operating temperature on the performance of hydrogen sensors was studied. The sensors obtain an extremely high response over 20000 to 30 ppm H-2 at the relatively low operating temperature of 75-125 degrees C. The Pd NPs@SnO2/PI sensor achieves a wide detection range of 0.1-5000 ppm with the limit of detection (LOD) of 100 ppb at 125 degrees C. A low LOD of 250 ppb can still be achieved at room temperature. The sensors also exhibit outstanding sensing selectivity for hydrogen over interfering gases and excellent mechanical resistance after 2000 bending cycles. The mechanism for improved sensing performance of ALD ultrathin film with CBD-derived noble metal NPs decoration may be a feasible strategy for the construction of highly sensitive, selective, and flexible hydrogen sensors.
Nano-Schottky Junction-Engineered Pd/SnO2 Nanotube Array for Ultrasensitive Hydrogen Sensing at Room Temperature

Zhilong Song,Weihao Fang,Bingchen Zhu,Jia Yan

DOI: https://doi.org/10.1039/d4ay00988f

IF: 3.1

2024-08-18

Analytical Methods

Abstract:Low-concentration H2 detection is of significance due to its major concern for safety in practical applications. However, semiconductor chemiresistive gas sensors always suffer from high operating temperature and power consumption, as well as a limited range of concentration detection, which restricts their widespread use. Herein, we developed a 3D nanostructured gas sensor employing Pd nanoclusters decorated SnO2 nanotube array as the sensing layer. The sensor shows sensitive and selective properties for low-concentration H2 detection at room temperature, and the limit of detection was down to 1.6 ppb. It also shows good long-term stability as long as 100 days. Moreover, systematical characterizations are performed in conjunction with density functional theory (DFT) calculations to determine the impact of Pd/SnO2 junctions on the gas-sensing properties improvement. The engineering of the nano-Schottky junction allows us to expand the library for designing low-power consumption H2 sensors for wide applications.

spectroscopy,chemistry, analytical,food science & technology
Hydrogen sensing and mechanism of M-doped SnO2 (M = Cr 3+, Cu2+ and Pd2+) nanocomposite

Wen Zeng,Tianmo Liu,Dejun Liu,Erjing Han

DOI: https://doi.org/10.1016/j.snb.2011.08.008

2011-01-01

Abstract:The microstructure of M-doped SnO2 (M=Cr3+, Cu2+ and Pd2+) prepared by the sol–gel method and their gas-sensing performance were investigated. In particular, we focus on the effects of metallic ions on the hydrogen sensing behavior of the SnO2-based sensor. It is found that hydrogen gas response of SnO2 can be enhanced evidently by adding Pd2+, while such effect from Cr3+ and Cu2+ exhibits somewhat slight. A theoretical study based on first principles calculation shows that SnO2–Pd (110) surface enable adsorb more H2 gas and receive larger electrons from adsorbed H2 molecule, thereby holding the potential for the improvement of gas response to hydrogen.
Ultrasensitive and Selective Hydrogen Sensing of SnO 2 Nanofibers Decorated with Pd Single Atoms

Tao Xiang,Jianxin Yi

DOI: https://doi.org/10.1016/j.snb.2024.136022

IF: 9.221

2024-05-25

Sensors and Actuators B Chemical

Abstract:Highly accurate and sensitive hydrogen detection particularly at (sub)ppb level is crucial for large-scale use of green hydrogen energy. However, state-of-the-art hydrogen sensors usually have a ppm-level limit of detection (LOD). In this work, SnO 2 nanofibers were decorated with Pd single atoms using a scalable two-step annealing method, which remarkably boosted the H 2 sensing properties. The Pd-SnO 2 nanofiber sensor exhibited a response of 224 to 1000 ppm H 2 at the optimum operation temperature of 300°C, which was 107 times higher than that of SnO 2 , achieving an LOD as low as 0.6 ppb. Moreover, a fast response time of 8.4 s, excellent selectivity, and humidity tolerance were observed. The superior H 2 sensing performance of Pd-SnO 2 nanofiber was ascribed to excellent catalysis of Pd single atoms and formation of heterojunction.

chemistry, analytical,electrochemistry,instruments & instrumentation
Preparation and Hydrogen Sensitivity of Pd Doped SnO2 Nanostructured Gas Sensor

Xiao-meng WU,Yun-han LING,Jun-sheng LIAO,Xiao-shan ZHU,Xin ZHI,Xin-de BAI

DOI: https://doi.org/10.3969/j.issn.1000-6931.2007.z1.026

2007-01-01

Abstract:Porous SnO2 nanostructured film gas sensor was fabricated by spray pyrolysis route using tin chloride pentahydrate (SnCl4·5H2O) and PdCl2 dopant as starting material. The phase, morphology and porous microstructure of the samples were characterized by XRD, FE-SEM and BET, respectively. Hydrogen sensitivity test reveals that the nanostructured gas sensor processes rapid response in 10-4 concentration of H2 at temperature below 150°C, and the phenomenon can be attributed to pore structure and the improvement of gas absorption and catalytic effect of Pd dopant.
W18O49 nanowire array driven by PdCu nanocrystals for chemiresistive hydrogen MEMS sensors

Jihao Bai,Chengming Sui,Yuanzhen Liu,Fengmin Liu,Peng Sun,Geyu Lu

DOI: https://doi.org/10.1016/j.snb.2022.132967

2023-01-01

Abstract:Compared with single metals, alloy nanocrystals (NCs) usually exhibit some novel properties and are emerging in the field of gas sensors. Uniformly dispersed PdCu NCs have been successfully synthesized and used to decorate W18O49 (same as WO2.72) nanowire array assembled from ultrafine nanowires with diameters less than 2 nm for hydrogen detection. The final Micro-Electro-Mechanical System (MEMS)-based PdCu-W18O49 gas sensor shows excllent selectivity and responsiveness to hydrogen at low operating temperature. The significantly improved sensing performance can be attributed to the following: 1) Ultrafine one-dimensional W18O49 nanowires could provide lots of adsorption sites and transport channels for hydrogen detection, 2) the content of Pd active sites increases with the introduction of the Cu metal, 3) the electronic sensitization of PdO, 4) the PdCu alloy NCs have excellent selective capability for hydrogen gas as they generate PdHx compounds, and 5) Pd4+ ↔ Pd2+ catalytic redox cycle accelerates the water formation reaction during hydrogen sensing. This work is of great significance for the detection of hydrogen, and has application potential in monitoring hydrogen leakage.

chemistry, analytical,electrochemistry,instruments & instrumentation
Cu2O induced Au nanochains for highly sensitive dual-mode detection of hydrogen sulfide

Fangdou Zhang,Yanxue Shang,Ruyue Yu,Ying Wang,Fan Feng,Qi Guo,Jinyan Xing,Zhangyu Tian,Jingbin Zeng,Zifeng Yan

DOI: https://doi.org/10.1016/j.jhazmat.2022.129144

IF: 13.6

2022-08-15

Journal of Hazardous Materials

Abstract:Colorimetric and chemoresistive gas sensing methods have aroused great interest in H2S monitoring due to their unique merits of naked-eye readout, and highly sensitive and rapid detection. However, combining these two methods for gas detection, especially utilizing one material as their common sensing material is a grand challenge because they are inconsistent in sensing mechanism. Taking advantage of the strong chemical affinity of Cu2O for H2S and the excellent performance of localized surface plasmon resonance (LSPR) of Au nanoparticles (NPs) in the visible regions and its ability as a noble metal to enhance gas sensing property, the Cu2O-Au nanochains (NCs) were prepared for dual-mode detection of H2S gas. The Cu2O-Au chemoresistive gas sensor shows a 5-fold higher response than Cu2O sensor at room temperature with a low detection limit of 10 ppb. Such good performance is attributed to the spillover effect and catalytic activity of Au NPs, and the enhanced H2S adsorption after Au loading as revealed by density functional theory calculation. Test strips containing Cu2O-Au produced for gaseous H2S detection show superior color gradient changes (blue, yellow, and brown). Finally, the practicability of the method was validated by real-time monitoring H2S released from cell culture.

environmental sciences,engineering, environmental
Hydrogen Sensitivity Performance of Pd Doped SnO2 Nanostructured Film Fabricated by Spray Pyrolysis

Xiaomeng Wu,Yunhan Ling,Xin Zhi,Zhaohui Huang

DOI: https://doi.org/10.1166/jnn.2009.c008

2009-01-01

Journal of Nanoscience and Nanotechnology

Abstract:The present investigation dealt with the fabrication of H2 gas sensor based on Pd doped SnO2. Porous SnO2 nanostructured film were fabricated by spray pyrolysis route using tin chloride pentahydrate (SnCl4.5H2O) solution as starting material, and PdCl2 as a dopant. Resistance measurements at different temperatures and concentration of H2 have been carried out with the samples. Microstructure and palladium dopant have been found to be critical factors determining the gas sensing properties of Pd/SnO2 specimens. The comparative gas sensitivity tests showed the excellent H2 sensing properties of the sensor in air was suggested to arise mainly from the improvement of gas absorption and catalytic effect of nano Pd dopant.
Hydrogen gas sensor based on SnO2 nanospheres modified with Sb2O3 prepared by one-step solvothermal route

Haineng Bai,Hui Guo,Jin Wang,Yan Dong,Bin Liu,Fuqiang Guo,Dunjun Chen,Rong Zhang,Youdou Zheng

DOI: https://doi.org/10.1016/j.snb.2021.129441

2021-01-01

Abstract:In this work, an ultra-low-cost and ecofriendly solvothermal strategy was employed to prepare gas-sensing materials for heterostructured p-Sb2O3/n-SnO2 nanospheres. The morphology, microstructure and other characteristics of the prepared products were comprehensively studied by several analyzers. The results show that the present SnO2 nanospheres modified with Sb2O3, exhibit exceptional mesoporous structures and high specific surface areas, as well as prominent thermal stability (only 0.02 % mass loss). For the first time, the cost-effective gas sensor based on Sb2O3/SnO2 nanospheres was fabricated, which maintained excellent gas-sensing behavior of 697 % towards 100 ppm H-2 gas at operating temperature of 280 degrees C, with a fast response/recovery time of 29.8/13.4 s, and the limit of detection was down to 100 ppb (S = 7.1 %). In addition, the gas sensor had quite consistency, reproducibility, long-term stability (over 40 days), and unique selectivity towards H-2 gas. Investigations into a plausible gas-sensing mechanism imply that the p-n heterojunction, catalytic function of Sb2O3, mesopomus structures and high specific surface area synergistically induced the superior gas-sensing response. Undoubtedly, the present work may provide an outstanding strategy to improve H-2 gas response in extremely environmental applications.
Hydrogen gas detection of Nb2O5 nanoparticle-decorated CuO nanorod sensors

Hyejoon Kheel,Gun-Joo Sun,Jae Kyung Lee,Ali Mirzaei,Seungbok Choi,Chongmu Lee

DOI: https://doi.org/10.1007/s12540-017-6343-3

IF: 3.451

2017-01-01

Metals and Materials International

Abstract:Pristine and Nb2O5 nanoparticles-decorated CuO nanorods were prepared successfully by a two step process: the thermal evaporation of a Cu foil and the spin coating of NbCl5 solution on CuO nanorods followed by thermal annealing. X-ray diffraction was performed to examine the structure and purity of the synthesized nanoatuctures. Scanning electron microscopy was used to examine the morphology and shape of the nanostuctures. The Nb2O5 nanoparticles-decorated CuO nanorod sensor showed responses of ~217.05-862.54%, response times of ~161-199 s and recovery times of ~163-171 s toward H2 gas with concentrations in a range of 0.5 - 5% at the optimal working temperature of 300 °C. The Nb2O5 nanoparticle-decorated CuO nanorod sensor showed superior sensing performance to the pristine CuO nanorod sensor for the same H2 concentration range. The underlying mechanism for the enhanced hydrogen sensing performance of the CuO nanorods decorated with Nb2O5 nanoparticles is discussed.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Tin dioxide nanoparticles with high sensitivity and selectivity for gas sensors at sub-ppm level of hydrogen gas detection

Xi-Tao Yin,Wen-Dong Zhou,Jing Li,Pin Lv,Qi Wang,Dong Wang,Fa-yu Wu,Davoud Dastan,Hamid Garmestani,Zhicheng Shi,Ştefan Ţălu

DOI: https://doi.org/10.1007/s10854-019-01840-w

2019-07-12

Abstract:A wet chemical method was employed to prepare Au-loaded sensor using tin dioxide (SnO2) nanoparticles (NPs) which has excellent hydrogen (H2) gas sensing properties. The structural, compositional, morphological, and electrochemical properties of these materials are characterized by X-ray diffraction, field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy and electrochemical workstation, respectively. The results show that the response time of Au-loaded sensor based on SnO2 NPs to 100 ppm H2 is 26 s at 350 °C, which is much shorter than that of the pristine SnO2 sensor. Meanwhile, the effect of operating temperature and Au loading on 'n' value (factor for evaluating sensitivity response) is studied and the results demonstrated that the Au-loaded sensor based on SnO2 NPs can detect H2 gas down to 0.4 ppm. Moreover, the Au-loaded sensor based on SnO2 NPs with an excellent selectivity to H2 gas against carbon monoxide, methane, and sulfur dioxide is illustrated in this paper, which indicates that the Au-loaded sensor using SnO2 NPs is a good candidate for practical H2 sensors and other industrial applications. Statistical analysis was performed on the FESEM images of sensors based on SnO2 NPs and 0.5 atomic (at)% Au-loaded SnO2 NPs. Roughness parameters were evaluated and a correlation was established between the morphology, topography and chemical composition of the samples.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Room temperature hydrogen gas sensor based on nanocrystalline SnO2 thin film using sol–gel spin coating technique

Imad H. Kadhim,H. Abu Hassan

DOI: https://doi.org/10.1007/s10854-016-4304-0

2016-01-14

Abstract:High-quality nanocrystalline (NC) SnO2 thin film was grown on SiO2/Si substrate by sol–gel spin coating technique at low temperature. X-ray diffraction and field emission scanning electron microscopy results observed the high quality of the produced NC SnO2 thin film. A metal–semiconductor-metal (MSM) H2 gas sensor was fabricated utilizing palladium (Pd) metal and NC SnO2 thin film. Hydrogen (H2) sensing capabilities of the NC SnO2 thin film were examined at room temperature (RT), and the sensitivity was 600 % in the presence of 1000 ppm of H2. The sensing measurements for H2 gas at different temperatures (RT to 125 °C) were repeatable for over 50 min. The sensor showed a sensitivity of 1950 % at 125 °C upon exposure to 1000 ppm of H2. A significant variation in the sensitivity of the NC SnO2 thin film sensor was noticed at different concentrations of H2 at different operating temperatures. These high sensitivities are attributed to the increase in adsorption/desorption of gas molecules, which were achieved by increasing the porosity of the NC SnO2 thin film surface by adding glycerin to the sol solution. The high sensitivity of this H2 gas sensor at RT indicated that it has the capability to be used as a portable RT gas sensor.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Study of a New Hydrogen Sensor Based on the Synthesis of a Sputtered In–Sn–Zn-O Thin Film and Evaporated Palladium Nanoparticles

Pao-Chi Yao,Chi-Kang Kuo,Jung-Chuan Wang,Pai-Yi Chu,Wei-Chou Hsu,Wen-Chau Liu

DOI: https://doi.org/10.1109/ted.2024.3361844

IF: 3.1

2024-01-01

IEEE Transactions on Electron Devices

Abstract:A new and interesting hydrogen (H $_{\text{2}}$ ) gas sensor based on an In–Sn–Zn-O (ITZO) thin film modified with palladium nanoparticles (Pd NPs) on a sapphire (Al $_{\text{2}}$ O $_{\text{3}}$ ) substrate is manufactured and investigated herein. High-resolution scanning electron microscopy (HRSEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) are employed to study intrinsic material properties. Experimentally, under 1% H $_{\text{2}}$ /air gas, the fabricated Pd NP/ITZO sensor exhibits prominent sensing performance, including a higher sensing response S $_{\text{R}}$ of 12 890 with a response (recovery) time of 106 s (13 s), and a lower detectable content of 1 ppm H $_{\text{2}}$ /air at 225 $^{\circ}$ C is obtained. Moreover, the sensor shows high reproducibility, excellent selectivity, and long-term stability (91 days) toward H $_{\text{2}}$ gas.

engineering, electrical & electronic,physics, applied
Study of a New Hydrogen Gas Sensor Synthesized With a Sputtered Cerium Oxide Thin Film and Evaporated Palladium Nanoparticles

K. Chen,Jing-Shiuan Niu,Wen-Chau Liu

DOI: https://doi.org/10.1109/TED.2021.3093842

IF: 3.1

2021-08-01

IEEE Transactions on Electron Devices

Abstract:A new hydrogen (H2) gas sensor, synthesized with a radio frequency (RF) sputtered cerium oxide (CeO2) thin film and rapid thermal evaporated palladium (Pd) nanoparticles (NPs), is fabricated and reported herein. The employed Pd NPs can effectively increase the surface area/volume ( ${S}_{A}$ /V) ratio and catalytic reactivity of Pd metal, thereby substantially enhancing the adsorption effect of hydrogen molecules on the device surface and improving the related sensing performance. Energy-dispersive X-ray spectroscopy (EDS), atomic force microscopy (AFM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were employed to characterize the related properties of the studied device. Experimentally, a high sensing response of 120.2 under 1% H2/air gas at 350 °C with a relatively shorter response (recovery) time of 5 s (17 s) is obtained. The studied Pd NP/CeO2-based sensor device shows wide operating ranges of temperature (200 °C–400 °C) and hydrogen concentration (10 ppm—1% H2/air). A thermodynamic analysis employed to study the surface coverage of hydrogen molecules is reported in this work. The studied sensor device also exhibits the advantages of a simple structure, easy fabrication process, and relatively low cost.

Materials Science,Engineering,Chemistry
Optimizing coverage of palladium nanoparticles for a highly sensitive hydrogen gas sensor based on nanogaps via spray-deposition

Yongjian Ni,Wentian Wang,Chen Tang,Jingyuan Sun,Weifeng Zhang,Wanlei Gao,Qinghui Jin,Jiawen Jian,Jie Zou

DOI: https://doi.org/10.1007/s10854-024-12537-0

2024-04-16

Journal of Materials Science Materials in Electronics

Abstract:The Hydrogen (H 2 ) sensor based on palladium nanogaps (Pd NGs) offers the advantages of low detection limits and fast response times. It holds significant potential for early warning of H 2 leakages. However, the preparation methods of Pd NGs for such sensors are really complex. In this study, the spray-deposition method was introduced to streamline the preparation method of Pd NGs and optimize the quantity of Pd NGs by adjusting the coverage of Pd nanoparticles (Pd NPs). The effect of different coverage of Pd NPs on the gas sensing performance of the sensor was investigated. The results revealed that sensors with lower coverage exhibited higher H 2 sensitivity. The sensor exhibited a response time of 10 s at room temperature and shorten to 2 s at 100 °C in 2500 ppm H 2 . Furthermore, the sensor achieved a detection limit as low as 50 ppm. These findings offer a method for effectively optimizing the sensing performance of Pd NGs based H 2 sensors.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Nano‐Patterned CuO Nanowire Nanogap Hydrogen Gas Sensor with Voids

Muqing Zhao,Ryosuke Nitta,Seiichiro Izawa,Jun‐ichi Yamaura,Yutaka Majima

DOI: https://doi.org/10.1002/adfm.202415971

IF: 19

2024-11-07

Advanced Functional Materials

Abstract:Sub‐5‐ppb hydrogen (H2) detection and sub‐10‐s response and recovery times are achieved based on nano‐patterned polycrystalline CuO nanowires nanogap gas sensors with voids using electron‐beam lithography and unique annealing processes. Pre‐H2 annealing, void‐generating oxidation, and downscaled nanogap electrodes are key to improving the sensing performance. This study demonstrates the feasibility of using effective hydrogen sensors that meet high safety standards. Hydrogen (H2) is increasingly employed in industrial applications, such as developing hydrogen fuel cells for vehicles and power plants. However, H2 explodes at a concentration limit of 4%, necessitating the development of ultrasensitive hydrogen sensors capable of early‐stage detection of hydrogen leaks. In this study, nano‐patterned polycrystalline cupric oxide (CuO) nanowire array nanogap gas sensors with voids are fabricated using electron‐beam lithography and ex situ oxidization by annealing, which could detect 5 ppb H2 and show response and recovery times of less than 10 s without a baseline shift. Combining a pre‐H2 annealing process in Ar/H2 for Cu nanowires and a low‐rate oxidation process enhances the crystallinity of CuO nanowires, facilitating the preparation of polycrystalline CuO nanowires with voids, which is a significantly practical approach for the improvements of gas sensing properties. Response and recovery times of <10 s can be obtained for a gap separation of ≈30 nm. These improvements are discussed based on a high electric field of ≈1.3 MV cm−1. The relationship between the normalized response and H2 concentration is discussed based on the power law. This paper presents highly reliable and fast H2 sensors without a baseline shift to meet the demands of the hydrogen industry.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
High selectivity and response H2 sensors based on ZnO@ZIF-71@Ag nanorod arrays

Chaofan Ma,Tingting Zhou,Huimin Yang,Huiyu Su,Xiaoxia Wang,Qirui Wu,Xiang Guo,Dawen Zeng

DOI: https://doi.org/10.1016/j.ceramint.2023.03.090

IF: 5.532

2023-03-01

Ceramics International

Abstract:Hydrogen (H2) is widely used in industrial and medical, however its flammable and explosive nature requires economical and effective monitoring to ensure safety. In this work, ZnO@ZIF-71@Ag nanorod arrays were synthesized to provide an effective adsorption response to H2 through size effect and high catalytic activity by immobilizing Ag nanoparticles (NPs) into the pores of ZIF-71. The results of the gas sensitivity tests showed that the nanorod arrays were significantly more selective towards H2. Moreover, the response of ZnO@ZIF-71@Ag to 50 ppm H2 was 11 times higher than that of ZnO@ZIF-71 at a lower operating temperature (150°C). The size of the Ag NPs was demonstrated to be below 10 nm by TEM characterization, suggesting that Ag in the form of quantum dots (QDs) to bring an unignorable catalytic effect for breaking hydrogen molecule (H2) into highly active atoms ([H]). In addition, the result of Density Function Theory (DFT) calculation revealed that the adsorption energy of Ag-catalyzed [H] (−8.255 eV) was much higher than that of H2 (−4.222 eV) on ZnO (100), which results in elevated charge transfer to promote hydrogen sensing performance of ZnO@ZIF-71@Ag. In this study, a novel hydrogen sensor based on pore sieving and catalytic sensing mechanisms was obtained, which provides a new reference for the development of hydrogen sensors.

materials science, ceramics

Political tolerance: how adolescents deal with dissenting groups.

Sensitive H2 Gas Sensors Based on SnO2 Nanowires

Pd nanoparticles decorated SnO 2 ultrathin nanosheets for highly sensitive H 2 sensor: Experimental and theoretical studies

Ultra-large Sn3O4 nanosheets with Sn2+ defect for highly efficient hydrogen sensing

Ultrasensitive and Wide-Range Flexible Hydrogen Sensor Based on Pd Nanoparticles Decorated Ultrathin SnO<sub>2</sub> Film

Nano-Schottky Junction-Engineered Pd/SnO2 Nanotube Array for Ultrasensitive Hydrogen Sensing at Room Temperature

Hydrogen sensing and mechanism of M-doped SnO2 (M = Cr 3+, Cu2+ and Pd2+) nanocomposite

Ultrasensitive and Selective Hydrogen Sensing of SnO 2 Nanofibers Decorated with Pd Single Atoms

Preparation and Hydrogen Sensitivity of Pd Doped SnO2 Nanostructured Gas Sensor

W18O49 nanowire array driven by PdCu nanocrystals for chemiresistive hydrogen MEMS sensors

Cu2O induced Au nanochains for highly sensitive dual-mode detection of hydrogen sulfide

Hydrogen Sensitivity Performance of Pd Doped SnO2 Nanostructured Film Fabricated by Spray Pyrolysis

Hydrogen gas sensor based on SnO<sub>2</sub> nanospheres modified with Sb<sub>2</sub>O<sub>3</sub> prepared by one-step solvothermal route

Hydrogen gas detection of Nb2O5 nanoparticle-decorated CuO nanorod sensors

Tin dioxide nanoparticles with high sensitivity and selectivity for gas sensors at sub-ppm level of hydrogen gas detection

Room temperature hydrogen gas sensor based on nanocrystalline SnO2 thin film using sol–gel spin coating technique

Study of a New Hydrogen Sensor Based on the Synthesis of a Sputtered In–Sn–Zn-O Thin Film and Evaporated Palladium Nanoparticles

Study of a New Hydrogen Gas Sensor Synthesized With a Sputtered Cerium Oxide Thin Film and Evaporated Palladium Nanoparticles

Optimizing coverage of palladium nanoparticles for a highly sensitive hydrogen gas sensor based on nanogaps via spray-deposition

Nano‐Patterned CuO Nanowire Nanogap Hydrogen Gas Sensor with Voids

High selectivity and response H2 sensors based on ZnO@ZIF-71@Ag nanorod arrays