Using Graph Metrics for Linked Open Data Enabled Recommender Systems

Petar Ristoski,M. Schuhmacher,Heiko Paulheim

DOI: https://doi.org/10.1007/978-3-319-27729-5_3

2015-09-03

Abstract:

What problem does this paper attempt to address?

Fully inkjet-printed Ag2Se flexible thermoelectric devices for sustainable power generation

Yan Liu,Qihao Zhang,Aibin Huang,Keyi Zhang,Shun Wan,Hongyi Chen,Yuntian Fu,Wusheng Zuo,Yongzhe Wang,Xun Cao,Lianjun Wang,Uli Lemmer,Wan Jiang

DOI: https://doi.org/10.1038/s41467-024-46183-1

IF: 16.6

2024-03-08

Nature Communications

Abstract:Abstract Flexible thermoelectric devices show great promise as sustainable power units for the exponentially increasing self-powered wearable electronics and ultra-widely distributed wireless sensor networks. While exciting proof-of-concept demonstrations have been reported, their large-scale implementation is impeded by unsatisfactory device performance and costly device fabrication techniques. Here, we develop Ag 2 Se-based thermoelectric films and flexible devices via inkjet printing. Large-area patterned arrays with microscale resolution are obtained in a dimensionally controlled manner by manipulating ink formulations and tuning printing parameters. Printed Ag 2 Se-based films exhibit (00 l )-textured feature, and an exceptional power factor (1097 μWm −1 K −2 at 377 K) is obtained by engineering the film composition and microstructure. Benefiting from high-resolution device integration, fully inkjet-printed Ag 2 Se-based flexible devices achieve a record-high normalized power (2 μWK −2 cm −2 ) and superior flexibility. Diverse application scenarios are offered by inkjet-printed devices, such as continuous power generation by harvesting thermal energy from the environment or human bodies. Our strategy demonstrates the potential to revolutionize the design and manufacture of multi-scale and complex flexible thermoelectric devices while reducing costs, enabling them to be integrated into emerging electronic systems as sustainable power sources.

multidisciplinary sciences
High-Performance Printed Ag2Se/PI Flexible Thermoelectric Film for Powering Wearable Electronics

Santosh Kumar,Manjusha Battabyal,Kanikrishnan Sethupathi,Dillip K Satapathy

DOI: https://doi.org/10.1021/acsami.4c05537

2024-08-07

Abstract:We report the magnificent thermoelectric properties of the n-type Ag2Se film printed onto a flexible polyimide (PI) substrate. The orthorhombic β-Ag2Se phase of the processed Ag2Se film is confirmed from the X-ray diffractogram. Remarkably, the resulting Ag2Se/PI film exhibits outstanding thermoelectric properties, boasting maximum power factors of 1.4 and 2.1 mW/mK2 at 300 and 405 K, respectively. Furthermore, the flexibility of the Ag2Se/PI film remains intact even after undergoing 1500 bending cycles with no degradation observed in its thermoelectric performance. To demonstrate the practical application of our findings, a flexible thermoelectric prototype is constructed using the fabricated Ag2Se/PI films, which can harvest an impressive output voltage of 52 mV across a temperature difference of 53 K. Additionally, the prototype generates a maximum power output of 7.2 μW with a 40 K temperature difference and can produce 13 mV output voltage when subjected to around a 10 K temperature gradient when the cold side temperature is maintained at 308 K. Moreover, leveraging body heat with just a 1 K temperature variance between the body and the surrounding environment, the prototype could yield an impressive voltage output of 1.6 mV, marking the highest reported voltage output from human body heat to date. Our study not only introduces a cost-effective method for producing high-performance flexible thermoelectric films but also highlights their potential applications in wearable and implantable electronics.
Inkjet Printing Flexible Thermoelectric Devices Using Metal Chalcogenide Nanowires

Jingjie Du,Botao Zhang,Meng Jiang,Qihao Zhang,Keyi Zhang,Yan Liu,Lianjun Wang,Wan Jiang

DOI: https://doi.org/10.1002/adfm.202213564

IF: 19

2023-03-30

Advanced Functional Materials

Abstract:Templated‐directed chemical transformation process combined with economic and scalable inkjet printing enables translating the superior properties of nanoscale thermoelectric materials to macroscale high‐performance flexible thermoelectric devices. Development of flexible thermoelectric devices offers exciting opportunities for wearable applications in consumer electronics, healthcare, human–machine interface, etc. Despite the increased interests and efforts in nanotechnology‐enabled flexible thermoelectrics, translating the superior properties of thermoelectric materials from nanoscale to macroscale and reducing the manufacturing costs at the device level remain a major challenge. Here, an economic and scalable inkjet printing method is reported to fabricate high‐performance flexible thermoelectric devices. A general templated‐directed chemical transformation process is employed to synthesize several types of 1D metal chalcogenide nanowires (e.g., Ag2Te, Cu7Te4, and Bi2Te2.7Se0.3). These nanowires are made into inks suitable for inkjet printing by dispersing them in ethanol without any additives. As a showcase for thermoelectric applications, fully inkjet‐printed Ag2Te‐based flexible films and devices are prepared. The printed films exhibit a power factor of 493.8 μW m−1 K−2 at 400 K and the printed devices demonstrate a maximum power density of 0.9 μW cm−2 K−2, both of which are significantly higher than those reported in state‐of‐the‐art inkjet‐printed thermoelectrics. The protocols of metal chalcogenide ink formulations, as well as printing are general and extendable to a wider range of material systems, suggesting the great potential of this printing platform for scalable manufacturing of next‐generation, high‐performance flexible thermoelectric devices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
High-Performance Ag2Se Film by a Microwave-Assisted Synthesis Method for Flexible Thermoelectric Generators

Zixing Wang,Ying Liu,Jiajia Li,Changjun Huang,Kefeng Cai

DOI: https://doi.org/10.3390/molecules28176397

IF: 4.6

2023-09-02

Molecules

Abstract:Flexible Ag2Se thermoelectric (TE) films are promising for wearable applications near room temperature (RT). Herein, a Ag2Se film on a nylon membrane with high TE performance was fabricated by a facile method. First, Ag2Se powders were prepared by a microwave-assisted synthesis method using Ag nanowires as a template. Second, the Ag2Se powders were deposited onto nylon via vacuum filtration followed by hot pressing. Through modulating the Ag/Se molar ratio for synthesizing the Ag2Se powders, an optimized Ag2Se film demonstrates a high power factor of 1577.1 μW m−1 K−2 and good flexibility at RT. The flexibility of the Ag2Se film is mainly attributed to the flexible nylon membrane. In addition, a six-leg flexible TE generator (f-TEG) fabricated with the optimized Ag2Se film exhibits a maximum power density of 18.4 W m−2 at a temperature difference of 29 K near RT. This work provides a new solution to prepare high-TE-performance flexible Ag2Se films for f-TEGs.

chemistry, multidisciplinary,biochemistry & molecular biology
Flexible power generators by Ag2Se thin films with record-high thermoelectric performance

Dong Yang,Xiao-Lei Shi,Meng Li,Mohammad Nisar,Adil Mansoor,Shuo Chen,Yuexing Chen,Fu Li,Hongli Ma,Guang Xing Liang,Xianghua Zhang,Weidi Liu,Ping Fan,Zhuanghao Zheng,Zhi-Gang Chen

DOI: https://doi.org/10.1038/s41467-024-45092-7

2024-01-31

Abstract:Exploring new near-room-temperature thermoelectric materials is significant for replacing current high-cost Bi2Te3. This study highlights the potential of Ag2Se for wearable thermoelectric electronics, addressing the trade-off between performance and flexibility. A record-high ZT of 1.27 at 363 K is achieved in Ag2Se-based thin films with 3.2 at.% Te doping on Se sites, realized by a new concept of doping-induced orientation engineering. We reveal that Te-doping enhances film uniformity and (00l)-orientation and in turn carrier mobility by reducing the (00l) formation energy, confirmed by solid computational and experimental evidence. The doping simultaneously widens the bandgap, resulting in improved Seebeck coefficients and high power factors, and introduces TeSe point defects to effectively reduce the lattice thermal conductivity. A protective organic-polymer-based composite layer enhances film flexibility, and a rationally designed flexible thermoelectric device achieves an output power density of 1.5 mW cm-2 for wearable power generation under a 20 K temperature difference.
Flexible Porous Ag2Se Films: From Freestanding Inorganic Films to Inorganic‐Network/Organic‐Skeleton Thermoelectric Generators

Hengyang Wang,Xinyu Lin,Guang Han,Bin Zhang,Yao Chen,Lin Zhang,Xu Lu,Guoyu Wang,Xiaoyuan Zhou

DOI: https://doi.org/10.1002/adfm.202413605

IF: 19

2024-09-25

Advanced Functional Materials

Abstract:Freestanding Ag2Se inorganic films with favorable thermoelectric properties and flexibility are fabricated via a "porous microstructure design" strategy. Further, a composite structure consisting of a Ag2Se conductive network and a polydimethylsiloxane (PDMS) skeleton significantly improves the films' stability under bending and twisting, facilitating the fabrication of flexible thermoelectric generators for potential near‐room‐temperature applications. Silver selenide (Ag2Se) flexible films are promising near‐room‐temperature thermoelectric candidates for low‐grade heat harvesting. However, existing Ag2Se films are generally attached on substrates, which impedes further flexibility improvement of the films and constrains the scenarios of applications. Here a cost‐effective and scalable strategy is presented, which combines screen printing and annealing, for synthesizing freestanding Ag2Se inorganic films with different densities of pores. High‐density pores and thin thickness endow the films with high flexibility, while films with low‐density pores obtain higher power factor. Furthermore, by utilizing the porous microstructure, a composite structure consisting of a Ag2Se conductive network and an organic polydimethylsiloxane (PDMS) skeleton is fabricated, which further improves films' stability under bending and torsion. Finally, a flexible thermoelectric generator comprising five Ag2Se/PDMS legs and encapsulated PDMS outputs a voltage of 20.2 mV and a maximum power of 810 nW (the corresponding power density is 5.4 W m−2) at a temperature difference of 30 K, verifying potential application at near room temperature. This work offers a useful paradigm for fabricating substrate‐free Ag2Se porous films with high flexibility for near‐room‐temperature thermoelectric applications.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Deviceization of high-performance and flexible Ag2Se films for electronic skin and servo rotation angle control

Yue-Xing Chen,Xiao-Lei Shi,Jun-Ze Zhang,Mohammad Nisar,Zhong-Zhao Zha,Zi-Nan Zhong,Fu Li,Guang-Xing Liang,Jing-Ting Luo,Meng Li,Tianyi Cao,Wei-Di Liu,Dong-Yan Xu,Zhuang-Hao Zheng,Zhi-Gang Chen

DOI: https://doi.org/10.1038/s41467-024-52680-0

2024-09-27

Abstract:Ag2Se shows significant potential for near-room-temperature thermoelectric applications, but its performance and device design are still evolving. In this work, we design a novel flexible Ag2Se thin-film-based thermoelectric device with optimized electrode materials and structure, achieving a high output power density of over 65 W m-2 and a normalized power density up to 3.68 μW cm-2 K-2 at a temperature difference of 42 K. By fine-tuning vapor selenization time, we strengthen the (013) orientation and carrier mobility of Ag2Se films, reducing excessive Ag interstitials and achieving a power factor of over 29 μW cm-1 K-2 at 393 K. A protective layer boosts flexibility of the thin film, retaining 90% performance after 1000 bends at 60°. Coupled with p-type Sb2Te3 thin films and rational simulations, the device shows rapid human motion response and precise servo motor control, highlighting the potential of high-performance Ag2Se thin films in advanced applications.
Fabricating different patterns of flexible inorganic semiconductor films via colloidal ink printing on textiles

Yunhuan Yuan,Senpei Xie,Chaogang Ding,Jun Wei,KeWei Li,Xiang-Peng Kong,Jie Xu,Kang Li,Weiwei Zhao

DOI: https://doi.org/10.1016/j.matlet.2021.131079

IF: 3

2022-01-01

Materials Letters

Abstract:As an important material for modern electronics, inorganic semiconductors have gradually been introduced into the field of printed electronics, which is one of the current hotspots in academia and industry. However, due to its inherent rigidity and preparation challenges of uniform homogeneous ink, inorganic semiconductor applications are severely limited. In this study, we demonstrate a scheme to fabricate flexible inorganic semiconductor films on various substrates at low temperature. And this film that can be bent 100,000 times was obtained using screen printing and low temperature annealing.

materials science, multidisciplinary,physics, applied
Flexible Thermoelectric Devices of Ultrahigh Power Factor by Scalable Printing and Interface Engineering

Tony Varghese,Chaochao Dun,Nicholas Kempf,Mortaza Saeidi‐Javash,Chinnathambi Karthik,Joseph Richardson,Courtney Hollar,David Estrada,Yanliang Zhang

DOI: https://doi.org/10.1002/adfm.201905796

IF: 19

2019-11-14

Advanced Functional Materials

Abstract:Printing is a versatile method to transform semiconducting nanoparticle inks into functional and flexible devices. In particular, thermoelectric nanoparticles are attractive building blocks to fabricate flexible devices for energy harvesting and cooling applications. However, the performance of printed devices are plagued by poor interfacial connections between nanoparticles and resulting low carrier mobility. While many rigid bulk materials have shown a thermoelectric figure of merit ZT greater than unity, it is an exacting challenge to develop flexible materials with ZT near unity. Here, a scalable screen‐printing method to fabricate high‐performance and flexible thermoelectric devices is reported. A tellurium‐based nanosolder approach is employed to bridge the interfaces between the BiSbTe particles during the postprinting sintering process. The printed BiSbTe flexible films demonstrate an ultrahigh room‐temperature power factor of 3 mW m−1 K−2 and ZT about 1, significantly higher than the best reported values for flexible films. A fully printed thermoelectric generator produces a high power density of 18.8 mW cm−2 achievable with a small temperature gradient of 80 °C. This screen‐printing method, which directly transforms thermoelectric nanoparticles into high‐performance and flexible devices, presents a significant leap to make thermoelectrics a commercially viable technology for a broad range of energy harvesting and cooling applications.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Enhanced Thermoelectric Performance in Flexible Sulfur-Alloyed Ag2Se Thin Films

Yi Luo,Shuaihang Hou,Yijie Liu,Xiaoyu Sun,Zunqian Tang,Fangyuan Yu,Jun Mao,Qian Zhang,Feng Cao

DOI: https://doi.org/10.1021/acsami.4c07009

IF: 9.5

2024-01-01

ACS Applied Materials & Interfaces

Abstract:Flexible thermoelectric generators can directly convert thermal energy harvested from the human body into electricity. The Ag2Se flexible film, a promising material for wearable thermoelectric generators, normally demonstrates an inferior electrical transport property due to its weakened in-plane mobility. In this study, the in-plane electrical transport properties of flexible Ag2Se films were optimized by alloying with additional sulfur. This optimization is achieved by leveraging the differences in elemental electronegativity and the preferred orientation of the Ag2Se films. The sulfur-alloyed Ag2Se thin film, with a nominal ratio of 3 atom %, can reach a maximum mobility of 1150 cm(-2) V-1 s(-1) at 300 K. So, the optimized room-temperature power factor increases to 1935 mu W m(-1) K-2. Furthermore, the Ag2Se film alloyed with 3 atom % sulfur exhibits excellent flexibility even after 1000 bending cycles with a radius of 5 mm, characterized by a relative resistance increment of less than 3%. In addition, the corresponding pi-type flexible thermoelectric generator possesses a maximum power density of 51 W m(-2) at a temperature difference of 50 K.
Solvent-assisted synthesis of Ag2Se and Ag2S nanoparticles on carbon fabric for enhanced thermoelectric performance

J Vinodhini,V Shalini,S Harish,H Ikeda,J Archana,M Navaneethan

DOI: https://doi.org/10.1016/j.jcis.2023.07.090

Abstract:The challenge of developing low-cost, highly flexible, and high-performance thermoelectric (TE) materials persists due to the low thermoelectric efficiency of conducting polymers and the inflexibility of inorganic materials. In this study, we successfully integrated Ag2Se and Ag2S with highly conductive carbon fabric (CF) to produce a flexible thermoelectric material. A facile one-step solvothermal method was employed to synthesize the Ag2Se-CF and Ag2S-CF, which were then subjected to X-ray analysis to confine the phase formation of Ag2Se and Ag2S on the carbon fabric. The analysis revealed that Ag2Se and Ag2S nanoparticles were tightly packed on the surface of carbon fabric, and compositional analysis confirmed the interaction between the material and carbon fabric. The thermoelectric properties of Ag2Se-CF and Ag2S-CF were significantly altered due to carrier concentration and mobility variations, resulting in a low power factor of 6.7 μW/mK2 for Ag2Se-CF and a high-power factor of 24 μW/mK2 at 373 K for Ag2S-CF. The growth of Ag2Se-CF and Ag2S-CF on carbon fabric led to an enhancement in their thermoelectric properties. Further, TE legs were fabricated using the Ag2Se-CF (p-type) and Ag2S-CF (n-type), and the fabricated legs exhibited an output voltage of ∼20 mV to ∼86.65 mV at a temperature gradient (ΔT) of 3-8 K. This work represents a cutting-edge approach to the fabrication of high-performance, wearable thermoelectric devices.
High-Performance Thermoelectric Flexible Ag 2 Se-Based Films with Wave-Shaped Buckling via a Thermal Diffusion Method

Junze Zhang,Mohammad Nisar,Hanwen Xu,Fu Li,Zhuanghao Zheng,Guangxing Liang,Ping Fan,Yue-Xing Chen

DOI: https://doi.org/10.1021/acsami.3c12486

IF: 9.5

2023-10-03

ACS Applied Materials & Interfaces

Abstract:Herein, an n-type Ag(2)Se thermoelectric flexible thin film has been fabricated on a polyimide (PI) substrate via a novel thermal diffusion method, and the thermoelectric performance is well-optimized by adjusting the pressure and temperature of thermal diffusion. All of the Ag(2)Se films are beneficial to grow (013) preferred orientations, which is conducive to performing a high Seebeck coefficient. By increasing the thermal diffusion temperature, the electrical conductivity can be rationally...

materials science, multidisciplinary,nanoscience & nanotechnology
High-performance and flexible thermoelectric films by screen printing solution-processed nanoplate crystals

Tony Varghese,Courtney Hollar,Joseph Richardson,Nicholas Kempf,Chao Han,Pasindu Gamarachchi,David Estrada,Rutvik J. Mehta,Yanliang Zhang

DOI: https://doi.org/10.1038/srep33135

IF: 4.6

2016-09-12

Scientific Reports

Abstract:AbstractScreen printing allows for direct conversion of thermoelectric nanocrystals into flexible energy harvesters and coolers. However, obtaining flexible thermoelectric materials with high figure of merit ZT through printing is an exacting challenge due to the difficulties to synthesize high-performance thermoelectric inks and the poor density and electrical conductivity of the printed films. Here, we demonstrate high-performance flexible films and devices by screen printing bismuth telluride based nanocrystal inks synthesized using a microwave-stimulated wet-chemical method. Thermoelectric films of several tens of microns thickness were screen printed onto a flexible polyimide substrate followed by cold compaction and sintering. The n-type films demonstrate a peak ZT of 0.43 along with superior flexibility, which is among the highest reported ZT values in flexible thermoelectric materials. A flexible thermoelectric device fabricated using the printed films produces a high power density of 4.1 mW/cm2 with 60 °C temperature difference between the hot side and cold side. The highly scalable and low cost process to fabricate flexible thermoelectric materials and devices demonstrated here opens up many opportunities to transform thermoelectric energy harvesting and cooling applications.

multidisciplinary sciences
Flexible pCu2Se-nAg2Se thermoelectric devices via in situ conversion from printed Cu patterns

Jinqi Xie,Meng Han,Xiangliang Zeng,Dasha Mao,Haitong Li,Xiaoliang Zeng,Ruiheng Liu,Linlin Ren,Rong Sun,Jianbin Xu

DOI: https://doi.org/10.1016/j.cej.2022.135172

IF: 15.1

2022-05-01

Chemical Engineering Journal

Abstract:Flexible thermoelectric (TE) devices have great potential in wearable electronics, but there is great challenge to realize robust TE device with high performance via feasible integration process. Herein, based on precisely printed copper patterns, a flexible pCu2Se-nAg2Se TE device is initially realized by in situ ion exchange reaction. The as-prepared Cu2Se and Ag2Se films possess typical hierarchical defects including atomic scale vacancies, the nanosheet fragments and microscale porous structure, which could significantly scatter phonons in wide frequency range. Accordingly, ultra-low thermal conductivity (Cu2Se: 0.13 W m−1 K−1; Ag2Se: 0.15 W m−1 K−1) and optimal ZTs (Cu2Se: 0.5; Ag2Se: 0.7) are achieved. Meanwhile, the as-fabricated pCu2Se-nAg2Se TE device exhibits an excellent power density of 13.4 W m−2 at a temperature gradient of 40 K, which is among the highest values of printed in-plane film devices. Furthermore, the good adhesion between TE films and porous PI substrate endowed excellent flexibility and stability of pCu2Se-nAg2Se devices.
High Thermoelectric Performance and Ultrahigh Flexibility Ag 2 S 1- x Se x film on a Nylon Membrane

Miaomiao Wu,Jiajia Li,Ying Liu,Zixing Wang,Ping Wei,Wenyu Zhao,Kefeng Cai

DOI: https://doi.org/10.1021/acsami.2c21987

IF: 9.5

2023-02-07

ACS Applied Materials & Interfaces

Abstract:Flexible thermoelectric (TE) generators have recently attracted increasing attention as they have the potential to power wearable devices using the temperature difference between the human body and the environment. Ag(2)S is recently reported to have plasticity near room temperature; however, it has very low electrical conductivity, leading to its poor TE property. Here, to improve the TE property, different amounts of Se (Se/Ag(2)S molar ratios being 0.4, 0.5, and 0.6) solid...

materials science, multidisciplinary,nanoscience & nanotechnology
High-performance Ag2Se film by a template method for flexible thermoelectric generator

Zixing Wang,Ying Liu,Jiajia Li,Changjun Huang,Kefeng Cai

DOI: https://doi.org/10.1016/j.mtphys.2023.101147

IF: 11.021

2023-06-01

Materials Today Physics

Abstract:Herein, we develop a facile method to prepare a high-performance Ag2Se thermoelectric (TE) film. First, Ag2Se powders were synthesized by the reaction between Ag nanowires (NWs) with Se precursor at room temperature (RT), then vacuum filtered on a nylon membrane, and finally hot pressed. The film exhibits a high power factor of 1636.9 μW m-1 K-2 at RT via optimizing the Ag/Se ratio. The film exhibits good flexibility because of the nylon substrate and the nylon well combined with the Ag2Se film. Moreover, a flexible TE generator (f-TEG) consisting of six optimized film legs was assembled, and it generates a maximum output power of ∼3.42 μW (corresponding power density of ∼13.5 W m-2) under a temperature gradient of 31.4 K. This work paves a simple, fast, and feasible route to prepare high-performance flexible Ag2Se film.

materials science, multidisciplinary,physics, applied
Flexible thermoelectric Cu–Se nanowire/methyl cellulose composite films prepared via screen printing technology

Jie Qin,Yong Du,Qiufeng Meng,Qinfei Ke

DOI: https://doi.org/10.1016/j.coco.2022.101467

IF: 8

2022-12-17

Composites Communications

Abstract:Cu–Se nanowires (NWs) have been successfully synthesized by a wet chemical method and then flexible Cu–Se NW/methyl cellulose (MC) composite films have been prepared via a screen printing technology. The thermoelectric properties of the composite films were enhanced by a cold-pressing combining annealing treatment. A power factor of 121.87 μWm −1 K −2 has been achieved for the Cu–Se NW/MC composite films at 380 K. A flexible thermoelectric generator (f-TEG) assembled by 4-leg of the as-prepared composite films can generate an output voltage of 0.83 mV and a maximum output power of 6.71 nW at a ΔT = 9.5 K. After being bent for 500 cycles, the resistance change ratio of the f-TEG along the strip length direction was only 3.69%, indicating that the f-TEG has a favorable stability. The screen printing process has many advantages, such as low cost, large-scale production, easy for operation, and therefore, it has a great potential for fabrication of flexible inorganic-organic thermoelectric composite films.

materials science, composites
Extraordinary self-powered Y-shape flexible film thermoelectric device for wearables

Xinjie Yuan,Pengfei Qiu,Chuanyao Sun,Shiqi Yang,Yi Wu,Lidong Chen,Xun Shi

DOI: https://doi.org/10.1039/d4ee01742k

IF: 32.5

2024-06-11

Energy & Environmental Science

Abstract:Wearables ungently demand the efficient flexible film thermoelectric (TE) technology to self-power the integral electronics. However, limited by the strong correlation between the thickness and temperature gradient across TE legs, film TE devices adopting traditional vertical and lateral π-shape configurations are extremely difficult to simultaneously realize excellent flexibility and large power output. In this work, we develop a Y-shape configuration to solve the dilemma between small thickness and large temperature gradient for TE legs. By using the recently discovered high-performance room-temperature ductile inorganic TE material Ag2Se0.67S0.33, we successfully fabricate extraordinary Y-shape flexible film TE devices. With the assistance of rational structure design and high-quality Ag2Se0.67S0.33/Pt interface, our devices demonstrate excellent flexibility, large temperature gradient across the TE legs, and record-high output power density among flexible film TE devices when it is worn on human body. The generated electricity can drive an electronic watch, showing the great potential for wearable electronics.

energy & fuels,chemistry, multidisciplinary,engineering, chemical,environmental sciences
Ultra-flexible self-supporting Ag 2 Se/nylon composite films for wearable thermoelectric devices

Jiajia Li,Ying Liu,Zixing Wang,Lidong Chen,Kefeng Cai

DOI: https://doi.org/10.1016/j.compositesb.2023.110946

2023-08-23

Abstract:Recently, flexible thermoelectric (TE) generators (f-TEGs) have received a lot of attention. Compared with TE films on flexible substrates, self-supporting composite films prepared by combining TE materials with soft fabrics and thus retaining the inherent advantages of fabrics, such as stretchability, breathability, and flexibility, are more practical and may significantly expand the application of f-TEGs in smart wearable devices. Hence, in this work, a facile and rapid method for preparing ultra-flexible self-supporting Ag 2 Se/nylon composite films is developed. The composite films with both TE properties and flexibility were obtained by fast selenization of commercial Ag/nylon fiber fabrics in a short time (60 s) at room temperature and then hot pressing at 230 °C in a vacuum. The maximum power factor of an optimized composite film at room temperature can reach 73.7 μW m −1 K −2 . Meanwhile, the film exhibits excellent flexibility with the Seebeck coefficient and electrical conductivity decreased by only 7.37 and 8.48% after being bent 4000 repetitions around a round bar with a radius of 4 mm, which exceeds most reported flexible TE films. The ultra-high flexibility is mainly attributed to its high content of the nylon matrix (∼85.05 wt%), the tight bonding between Ag 2 Se grains, and the good combination between the Ag 2 Se and nylon matrix. In addition, a 3-leg f-TEG assembled with the optimal film produces a maximum power of ∼1.524 μW (corresponding to a power density of ∼0.47 W m −2 ) at a temperature gradient of 40.6 K, verifying the good TE performance of the composite film. This f-TEG can also be used as a self-powered temperature sensor, showing potential applications in daily life.

engineering, multidisciplinary,materials science, composites
Microstructurally Tailored Thin Β‐ag2se Films Toward Commercial Flexible Thermoelectrics

Yan Lei,Ruijuan Qi,Miaoying Chen,Hong Chen,Chengcheng Xing,Fengrui Sui,Longyan Gu,Weiwei He,Yange Zhang,Takahiro Baba,Tetsuya Baba,Hong Lin,Takao Mori,Kunihito Koumoto,Yuan Lin,Zhi Zheng

DOI: https://doi.org/10.1002/adma.202104786

IF: 29.4

2021-01-01

Advanced Materials

Abstract:Aiming to overcome both the structural and commercial limitations of flexible thermoelectric power generators, an efficient room-temperature aqueous selenization reaction that can be completed in air within less than 1 min, to directly fabricate thin beta-Ag2Se films consisting of perfectly crystalline and large columnar grains with both in-plane randomness and out-of-plane [201] preferred orientation, is designed. A high power factor (PF) of 2590 +/- 414 mu W m(-1) K-2 and a figure-of-merit (zT) of 1.2 +/- 0.42 are obtained from a sample with a thickness of approximate to 1 mu m. The maximum output power density of the best 4-leg thermoelectric generator sample reach 27.6 +/- 1.95 and 124 +/- 8.78 W m(-2) at room temperature with 30 and 60 K temperature differences, respectively, which may be useful in future flexible thermoelectric devices.

Using Graph Metrics for Linked Open Data Enabled Recommender Systems

Fully inkjet-printed Ag2Se flexible thermoelectric devices for sustainable power generation

High-Performance Printed Ag2Se/PI Flexible Thermoelectric Film for Powering Wearable Electronics

Inkjet Printing Flexible Thermoelectric Devices Using Metal Chalcogenide Nanowires

High-Performance Ag2Se Film by a Microwave-Assisted Synthesis Method for Flexible Thermoelectric Generators

Flexible power generators by Ag2Se thin films with record-high thermoelectric performance

Flexible Porous Ag2Se Films: From Freestanding Inorganic Films to Inorganic‐Network/Organic‐Skeleton Thermoelectric Generators

Deviceization of high-performance and flexible Ag2Se films for electronic skin and servo rotation angle control

Fabricating different patterns of flexible inorganic semiconductor films via colloidal ink printing on textiles

Flexible Thermoelectric Devices of Ultrahigh Power Factor by Scalable Printing and Interface Engineering

Enhanced Thermoelectric Performance in Flexible Sulfur-Alloyed Ag2Se Thin Films

Solvent-assisted synthesis of Ag2Se and Ag2S nanoparticles on carbon fabric for enhanced thermoelectric performance

High-Performance Thermoelectric Flexible Ag 2 Se-Based Films with Wave-Shaped Buckling via a Thermal Diffusion Method

High-performance and flexible thermoelectric films by screen printing solution-processed nanoplate crystals

Flexible pCu2Se-nAg2Se thermoelectric devices via in situ conversion from printed Cu patterns

High Thermoelectric Performance and Ultrahigh Flexibility Ag 2 S 1- x Se x film on a Nylon Membrane

High-performance Ag2Se film by a template method for flexible thermoelectric generator

Flexible thermoelectric Cu–Se nanowire/methyl cellulose composite films prepared via screen printing technology

Extraordinary self-powered Y-shape flexible film thermoelectric device for wearables

Ultra-flexible self-supporting Ag 2 Se/nylon composite films for wearable thermoelectric devices

Microstructurally Tailored Thin Β‐ag2se Films Toward Commercial Flexible Thermoelectrics