[Intraosseous lipomatosis: positivity in bone scintigraphy with 99mTc-HDP].

E. Mena,M. Estorch,V. Camacho,J. Fuertes,A. Tembl,M. A. Hernández,A. Flotats,I. Carrió

Revista Española de Medicina Nuclear

Abstract:

What problem does this paper attempt to address?

Experimental and Simulation Investigation on Fatigue Performance of H13 Steel Tools in Friction Stir Welding of Aluminum Alloys

Ling Long,Xiaohong Zhang,Song Gu,Xiuxin Li,Xuefeng Cheng,Gaoqiang Chen

DOI: https://doi.org/10.3390/ma17071535

IF: 3.4

2024-03-29

Materials

Abstract:As the central component in friction stir welding, the design and manufacture of welding tools for aluminum alloys have garnered substantial attention. However, the understanding of tool reliability during the welding process, especially in terms of fatigue performance, remains unclear. This paper focuses on the welding of AA2219-T4 as a case study to elucidate the predominant failure mode of the tool during the friction stir welding (FSW) of aluminum alloys. Experimental methods, including FSW welding and fracture morphology analysis of the failed tool, coupled with numerical simulation, confirm that high-cycle mechanical fatigue fracture is the primary mode of the tool failure. Failures predominantly occur at the tool pin's root and the shoulder end face with scroll concave grooves. The experimental and simulation results exhibit a noteworthy agreement, validating the reliability of the simulation model. The FSW Arbitrary Lagrangian–Eulerian (ALE) model developed in this study analyzes stress distribution and variation under the thermo-mechanical coupling effect of the tool. It reveals that stress concentration resulting from structural changes in the tool is the primary driver of fatigue crack initiation. This is attributed to exposure to alternating cyclic stresses such as bending, tension, and torsion at the tool pin's root, manifesting as multiaxial composite mechanical fatigue. Among these stresses, bending alternating cyclic stress exerts the most significant influence. The paper employs the Tool Life module in DEFORM software to predict the fatigue life of the tool. Results indicate that reducing welding speed or increasing rotation speed can enhance the tool's fatigue life to some extent. The methodology proposed in this paper serves as a valuable reference for optimizing FSW structures or processes to enhance the fatigue performance of welding tools.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Failure mechanisms of Friction stir welding tools related to process control and tool geometry

Michael Hasieber,Paul Rudel,Martin Sennewald,Torsten Löhn,Michael Grätzel,Jean Pierre Bergmann

DOI: https://doi.org/10.1177/14644207241228370

2024-02-01

Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications

Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. Friction stir welding (FSW) is subjected to process-specific challenges including comparatively high process forces and tool wear resulting from thermomechanical stresses. As a result, the acting loads and the geometric-related tool wear can cause tool failure. The tool (shoulder) design, whether it is concave or flat, with or without geometrical elements, is mainly responsible for the related failure mechanism and tool life. Therefore, this study systematically analyzes the failure mechanisms as a function of the process temperature, during FSW of AA-6060 T66 using tools made of H13 tool steel, with different shoulder designs, namely a concave contour and a scroll contour. The mechanism responsible for tool failure was induced by repeated welding at rotational speeds of 4000 rpm and 2000 rpm, at process temperatures within the range of the secondary hardness maximum (552 °C and 555 °C) and below the temperature of the secondary hardness maximum (488 °C and 499 °C). The experimental investigation showed that reducing the rotational speed of the scrolled shoulder from 4000 rpm to 2000 rpm resulted in less wear and therefore an increase in tool life from 474 m to up to 1400 m. In this context, it has also been shown that the shoulder geometry affects the mechanism relevant to failure due to the free length of the probe.

materials science, multidisciplinary
Thermal-fluid-structure coupling analysis of void defect in friction stir welding

Lei Shi,Jie Chen,Gaoqiang Chen,Chuansong Wu,Chuanliang Yang

DOI: https://doi.org/10.1016/j.ijmecsci.2022.107969

IF: 7.3

2022-11-24

International Journal of Mechanical Sciences

Abstract:Understanding the void defect formation mechanism and simultaneous predicting the tool service life in friction stir welding are critical for optimizing the welding parameters. However, the void defect formation mechanism in friction stir welding is not yet elucidated. In this study, a novel integrated thermal-fluid-structure coupling model of the friction stir welding process was proposed for simultaneous prediction of the weld formation and tool service life. A new non-uniform distribution model of the tool-workpiece contact pressure was proposed to describe the interaction between the tool and the workpiece. The void defect formation mechanism was quantitatively studied using the proposed integrated thermal-fluid-structure coupling model. The results show that the plastic material flows in the horizontal direction and can completely fill the cavity behind the tool for the welding condition of forming a sound weld. While the tool-workpiece contact interfacial frictional shear stress in the rear of the tool is decreased significantly which leads to a severe decrease in the plastic material flow velocity. Therefore, after bypassing the tool from the retreating side, the plastic material at the bottom of the weld stagnates, and void defect forms in the middle and lower part of the weld at the advancing side. The difference between the maximum and the minimum tool-workpiece contact pressure could serve as a numerical criterion to predict void defects. A sound joint is formed when the difference is lower than the critical value of 15 MPa, while a void defect is formed in the weld if it is higher than this critical value. The maximum equivalent stress acting on the tool is located at the pin root with severe stress concentration at a high welding speed. The front of the tool is subjected to tensile stress while its rear is subjected to compressive stress, therefore the tool is apt to fracture at its root under an inappropriate welding condition. The average normal stress of the tool varies periodically with its period consistent with the rotation period of the tool. The service life of the tool is decreased with the increase in welding speed and the decrease in rotation speed. The model is validated by experimental results.

engineering, mechanical,mechanics
Comparison of tool wear during friction stir welding of Al alloy and Al-SiC metal matrix composite

Ashish Bist,JS Saini,Vikas Sharma

DOI: https://doi.org/10.1177/09544089211005994

2021-03-31

Abstract:Aluminum matrix composites have received considerable attention due to their high specific strength and specific stiffness, high hardness, and wear resistance along with being light in weight. These composites are preferably joined using friction stir welding process. The major concern in friction stir welding is the wear of the welding tool pin which is the backbone of the process. The wear is due to the prolonged contact between the tool and the harder reinforcements in the composite materials. The present work deals with the study of tool wear and its surface roughness with respect to different selected friction stir welding parameters such as rotational speed, transverse speed, length of weld, and different composition of Aluminum composite. It was found that the total amount of material removed from the tool and the surface roughness of the tool is in direct proportion to the rotational speed of the tool and the length of the weld but inversely proportional to the transverse rate. The increase in wt.% of SiC reinforcement leads to the higher tool wear but reduces the surface roughness of the tool.

engineering, mechanical
Effect of Friction Stir Welding Tool Design on Welding Thermal Efficiency

Hongjun Li,Jian Gao,Qinchuan Li,Alexander Galloway,Athanasios Toumpis

DOI: https://doi.org/10.1080/13621718.2018.1495868

2019-01-01

Science and Technology of Welding & Joining

Abstract:Enhancing the heat transfer to the material being welded, instead of the tool, will improve the welding thermal efficiency. Friction stir welding of 5 mm thick 6061-T6 aluminium alloy plates was carried out with the newly produced tools. It was found that the thermal efficiency increased by 4.2% using a tool with all the new design features (i.e. hollow, fluted and thermally insulated) compared to the conventional tool for aluminium welding. To assess the benefits of the new tool design on steel FSW, a finite element numerical simulation study was undertaken. In this case, the simulation results yielded a welding thermal efficiency increase of 10–15% using a thermally coated tool, thereby offering potential productivity gains.
Effect of tool revolutionary pitch on heat transfer and material flow in Al/steel friction stir lap welding

Peihao Geng,Hong Ma,Pengkang Zhao,Ninshu Ma,Miura Takuya,Hidetoshi Fujii

DOI: https://doi.org/10.1016/j.jmatprotec.2024.118306

IF: 6.3

2024-01-21

Journal of Materials Processing Technology

Abstract:The motion condition of a friction stir welding tool significantly affects weld formation and quality in dissimilar joining between Al alloy and steel owing to its direct effect on thermo-mechanical condition during the process. In this study, a finite element simulation based on the coupled Eulerian–Lagrangian formulation was used to investigate the thermomechanical field evolutions in the friction stir lap welding of Al and steel, focusing on the effect of tool revolutionary pitch on thermal energy generation and material flow. Simulation results indicated that an increasing revolutionary pitch increased the proportion of heat input generated by plastic deformation, exhibiting an approximately linear relationship under the adopted welding parameters. With a fixed revolutionary pitch, a high- parameter-matching of rotational created higher welding temperatures. A lower revolutionary pitch resulted in higher welding temperature, leading to a thicker intermetallic layer at the Al/steel interface. However, a high revolutionary pitch under high-matching parameters significantly weakened the mixing of two materials behind the pin by decreasing material migration from the Al alloy and steel at the pin bottom on the restraining side, due to reduced temperature and increased deformation resistance. A parabolic mathematical correlation between interfacial strength and revolutionary pitch was observed, suggesting that maintaining a revolutionary pitch within the range of 0.4 to 1.2 mm/rev could produce a robust Al/steel lapped interface with joining efficiencies of approximately 91% or higher compared to the Al alloy base metal.

materials science, multidisciplinary,engineering, manufacturing, industrial
An Alternative Frictional Boundary Condition for Computational Fluid Dynamics Simulation of Friction Stir Welding

Gaoqiang Chen,Zhili Feng,Yucan Zhu,Qingyu Shi

DOI: https://doi.org/10.1007/s11665-016-2219-9

IF: 2.3

2016-01-01

Journal of Materials Engineering and Performance

Abstract:For better application of numerical simulation in optimization and design of friction stir welding (FSW), this paper presents a new frictional boundary condition at the tool/workpiece interface for computational fluid dynamics (CFD) modeling of FSW. The proposed boundary condition is based on an implementation of the Coulomb friction model. Using the new boundary condition, the CFD simulation yields non-uniform distribution of contact state over the tool/workpiece interface, as validated by the experimental weld macrostructure. It is found that interfacial sticking state is present over large area at the tool-workpiece interface, while significant interfacial sliding occurs at the shoulder periphery, the lower part of pin side, and the periphery of pin bottom. Due to the interfacial sticking, a rotating flow zone is found under the shoulder, in which fast circular motion occurs. The diameter of the rotating flow zone is smaller than the shoulder diameter, which is attributed to the presence of the interfacial sliding at the shoulder periphery. For the simulated welding condition, the heat generation due to friction and plastic deformation makes up 54.4 and 45.6% of the total heat generation rate, respectively. The simulated temperature field is validated by the good agreement to the experimental measurements.
Numerical Simulation of Material Flow Behavior of Friction Stir Welding Influenced by Rotational Tool Geometry

S. D. Ji,Q. Y. Shi,L. G. Zhang,A. L. Zou,S. S. Gao,L. V. Zan

DOI: https://doi.org/10.1016/j.commatsci.2012.06.001

IF: 3.572

2012-01-01

Computational Materials Science

Abstract:Considering the practical geometry of rotational tool and the relation between the material parameters and temperature, the finite volume model of friction stir welding is established on basis of the ANSYS FLUENT software. The effect of shoulder geometry and pin geometry on material plastic flow behavior is studied. The results of numerical simulation show that the flow velocity of material decreases with the increase of the distance away from the weldment surface or the rotational axis of pin. The flow velocity of material inside weldment is increased by decreasing the cone angle of pine or decreasing the width of screw groove. When the rotational tool with the left screw pin rotates clockwise, the flow direction of material near pin is downward while the flow direction near the thermal–mechanical affected zone is upward, which is opposite to that of the right screw pin. From the view of improvement of material flow, the concentric-circles-flute shoulder is better than the inner-concave-flute shoulder or the plane shoulder. Therefore, choosing the reasonable shoulder geometry and the reasonable pin geometry can be good for improving the material flow during the friction stir welding process and avoiding the root defects.
Numerical analysis on the functions of stir tool's mechanical loads during friction stir welding

Dongyang Yan,Qingyu Shi,Aiping Wu

DOI: https://doi.org/10.3321/j.issn:0412-1961.2009.08.016

2009-01-01

Abstract:Besides lower welding temperature and solid phase welding process, another significant difference between friction stir welding and conventional fusion welding (FSW) is that the forming of weld seam in FSW is effected by both thermal load and mechanical loads of stir tool. However, the definite functions of mechanical loads of stir tool in FSW process are not clearly described. With FSW experiments, only the material flow around stir tool can be observed, from which the results were obtained that the mechanical loads of stir tool gave birth to the plastic flow, a key factor of weld formation, of intenerated metal around the tool. In the simulation of FSW process, mechanical loads are always neglected in most analysis models, which can't describe the unique characteristic of FSW. Although the mechanical loads have been considered in FSW simulation by some researchers, the loads are greatly simplified and the analysis is only localized in the asymmetric distribution of residual stress. In this paper, numerical simulation was applied to investigate the functions of mechanical loads during FSW process. Based on experiments of FSW aluminium alloy sheets, three simulation models were established with different conditions of considering thermal load only, considering both thermal load and down force, and considering thermal load, down force and working torque synthetically. The results show that the down force significantly reduces residual stress and the torque leads to the unsymmetrical distribution of residual stress. On the other hand, mechanical loads absolutely change the residual distortion pattern from saddle state into anti-saddle state. Mechanical loads strengthen the mechanical restriction on sheet, forge and extrude the materials around tool, so the residual strain in weld zone is reduced, which leads to the reduction of residual stress. Furthermore, the mechanical loads change the correlation of strain on top surface and bottom surface of sheet, which resultes in the change of distortion pattern.
Study on the Microstructure and Mechanical Properties on Al/Carbon Fiber Reinforced Thermoplastic Dissimilar Friction Stir Lap Welding Joints

Zhang Yuan,Yibo Sun,Haiwei Long,Jianning Zhu,Li Zou,Xinhua Yang

DOI: https://doi.org/10.1007/s11665-024-09482-8

IF: 2.3

2024-05-01

Journal of Materials Engineering and Performance

Abstract:Friction stir welding (FSW) of dissimilar metals and polymers has shown some attractive applications in industrial fields such as drone tails and automotive parts. Adjusting process parameters is a fast and effective method to improve the tensile performance of joints. In this paper, the evaluation of friction stir lap welded joints between 6061-T6 aluminum alloy and carbon fiber reinforced thermoplastic (CFRTP) is conducted by studying the microstructure characteristics of the weld interface, SEM of the fracture surface, tensile and hardness analysis. The results indicate that the upper part of the weld cross-section joint experiences longer stirring and friction durations. The small metal fragments broken at the lower part of the joint are recombined into larger fragments. At high rotational speeds, the formation of welds is faster and more uniform. Metal fragments are further broken and refined and the molten CFRTP is uniformly mixed with Al alloy fragments in the stirring zone, which improvs the bonding property between two materials. Therefore, the value of tensile strength at 1800 rpm reaches 32.9 MPa, which is equivalent to 63.1% of CFRTP sheets.

materials science, multidisciplinary
A New Tooling Approach for Friction Stir Welding of Thin Sheet AA2024-T3 - Optimization of Welding Parameters

Piotr Myśliwiec

DOI: https://doi.org/10.7862/rm.2022.3

2022-01-01

Scientific Letters of Rzeszow University of Technology - Mechanics

Abstract:In this study a new ceramics tools with different groove distributions were designed and manufactured in order to enrich technological storage of joining thinwall structures and obtain sound joint with high quality of Alclad AA2024-T3 alloy of 0.5 mm in thickness. Four types of tools were tested, without grooves, with 1, 2 and 6 grooves. The tools are made of two materials. The straight shank is made from tungsten carbide and tool body made from ceramics strengthened with whiskers. The influence of technological parameters on the strength of FSW joints was tested by the Response Surface Methodology (RSM) and Analysis of Variance (ANOVA) method. The least durable weld is produced by a tool without grooves. The single and double flute tool produces a good quality weld over a wide range of tool speeds. It has been shown that the grooves on the tool shoulder significantly affect the quality of the obtained FSW joint.
Finite-element Analysis of the Tool Tilt Angle Effect on the Formation of Friction Stir Welds

Ling Long,Gaoqiang Chen,Shuai Zhang,Tie Liu,Qingyu Shi

DOI: https://doi.org/10.1016/j.jmapro.2017.10.023

IF: 5.684

2017-01-01

Journal of Manufacturing Processes

Abstract:The tool tilt angle is one of the key process parameters determining the weld quality during friction stir welding. However, the influence of tilt angle on the weld formation has not been fully understood. Hence, in this paper, a three-dimensional thermal-mechanical coupled finite element model is established, in which the tilt angle is considered in the geometric model. This model is shown to be able to predict the in-process thermal-mechanical state variables (e.g. temperature, flow path and stress) during the welding and the post-welding morphology of the weld. The predicted temperature distribution and weld morphology agree well with the corresponding experimental results. It is shown by the simulation results that wormhole defects appear in the weld with a zero tilt angle, while no such defects are observed in the case that the tilt angle of 2° is employed. In order to get a deeper understanding of the weld formation mechanism, the thermal-mechanical condition around the tool during welding with/without tilt angle are compared and analysed. It is found from our simulation that both the peak temperature and compressive normal stress on material in the rear side of the tool are elevated by including a tilt angle of 2°. This temperature increase induced by the tilt angle will significantly soften the workpiece, meanwhile higher frictional driving force in the rear side will be generated by the increased compressive force. Therefore, the material flow in the rear side of the tool with the title angle is significantly enhanced, which contributes to avoid the generation of wormhole defect on the advancing side.
Study on the influence of tool rotational speeds/welding traverse speeds on the quality and surface formation of 6mm copper friction stir welding

Tiancheng An,Xitong Li,Hongyong Xu,Changquan Lan,Linlin Song,Hui Hui

DOI: https://doi.org/10.1088/2053-1591/ad3168

IF: 2.025

2024-03-08

Materials Research Express

Abstract:This paper describes a study on the formation and process parameters of friction stir welding joints on 6mm thick copper plates. Numerous experiments were conducted at lower rotational speeds and moderate welding traverse speeds to obtain optimal process parameters for high-quality friction stir welding joints with good surface formation and no internal defects. Simultaneously, considering the thickness tolerance fluctuations in the large-scale engineering application of Copper FSW, tests were conducted with pin lengths and shoulder plunge depths less than the plate thickness. Additionally, a unique modular stirring tool was designed by ourselves to reduce costs in large-scale engineering applications. The experimental results demonstrate that under the parameters of a rotational speed of 275r/min and a traverse speed of 120mm/min, welding joints with both surface and internal integrity can be achieved, with the joint strength level exceeding 80% of the base material. The mechanical weak point of the joint is located in the TMAZ region just below the pin as revealed by SEM testing, which shows both plastic and brittle fractures. EDS results indicate no inclusions or second-phase precipitates at the surface and port locations.

materials science, multidisciplinary
Structural optimization study of stationary shoulder friction stir welding head with non-rigid support

Taotao Jin,Pei Miao,Chuanyue Qi,Xiuhui Cui

DOI: https://doi.org/10.1007/s00170-024-13845-9

IF: 3.563

2024-06-07

The International Journal of Advanced Manufacturing Technology

Abstract:To enhance the quality and efficiency of repairing aluminum alloy freight car bodies in railways, a friction stir head structure suitable for welding and repairing aluminum alloy freight car bodies was designed while employing stationary shoulder friction stir welding (SSFSW) technology. By analyzing the relationship between the structure of the friction stir welding head and the heat generation mechanism, a nearly stationary-shoulder friction stir head structure was proposed. Through the analytical heat generation model of the stationary shoulder stir pin, the functional relationship between the heat dissipation, stir pin dimensions, and process parameters was determined, and the geometric shape of the stir pin and the size of the stationary shoulder end cap were designed. Simulation and experimental results indicate that using this designed stir pin structure for welding repair, the temperature field of the weld seam is uniformly distributed along the thickness direction of the welded piece, which is conducive to forming good weld joints and seams. Practical field applications have shown that the designed structure can ensure heat generation while solving the problems of insufficient upsetting force and local stress concentration during non-rigid support processes, significantly improving the welding success rate. The tensile strength of the weld seam and other indicators also achieved satisfactory results. The design method used has certain referential value and can provide insights for similar research endeavors.

engineering, manufacturing,automation & control systems
Investigation of Tool Degradation during Friction Stir Welding of Hybrid Aluminum–Steel Sheets in a Combined Butt and Overlap Joint

Robin Göbel,Stefanie Schwertel,Stefan Weihe,Martin Werz

DOI: https://doi.org/10.3390/ma17040874

IF: 3.4

2024-02-15

Materials

Abstract:Friction stir welding, as a solid-state welding technique, is especially suitable for effectively joining high-strength aluminum alloys, as well as for multi-material welds. This research investigates the friction stir welding of thin aluminum and steel sheets, an essential process in the production of hybrid tailor-welded blanks employed in deep drawing applications. Despite its proven advantages, the welding process exhibits variable outcomes concerning formability and joint strength when utilizing an H13 welding tool. To better understand these inconsistencies, multiple welds were performed in this study, joining 1 mm thick steel to 2 mm thick aluminum sheets, with a cumulative length of 7.65 m. The accumulation of material on the welding tool was documented through 3D scanning and weighing. The integrity of the resulting weld seam was analyzed through metallographic sections and X-ray imaging. It was found that the adhering material built up continuously around the tool pin over several welds totaling between 1.5 m and 2.5 m before ultimately detaching. This accretion of material notably affected the welding process, resulting in increased intermixing of steel particles within the aluminum matrix. This research provides detailed insights into the dynamics of friction stir welding in multi-material welds, particularly in the context of tool material interaction and its impact on weld quality.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Effect of Stirring Pin on Interfacial Microstructure and Mechanical Properties of FSSW-B Joint

Liu Wenkuo,Xie Jilin,Chen Yuhua,Wang Hongwei,Zhang Timing,Wang Shanlin

2023-01-01

Rare Metal Materials and Engineering

Abstract:The aluminum/magnesium dissimilar metal composite structure has great application value in the field of structural lightweighting. In this paper, a novel friction stir spot welding- brazing (FSSW-B) technology was used for lap spot welding of aluminum/magnesium dissimilar metals. At the same time, it was compared with friction stir spot brazing (FSSB) technology to study the effect of the stirring pin in the welding tool on the microstructure and mechanical properties of the joint. The results show that the interface layer of FSSW-B joint is divided into two parts: the upper interface is mainly composed of MgZn2, and the lower interface is mainly composed of Mg7Zn3; the FSSB joint interface layer is mainly composed of MgZn2 phase. The fracture mode of the two kinds of joints is mainly interface peeling fracture, and the eyebrow-shaped fracture mode appears due to the existence of the stirring pin. The existence of the stirring pin improves the tensile shear resistance and fatigue performance of the joint. The maximum tensile shear force of the FSSW-B joint is 7600 N, and the fatigue limit is 3366.6 N; the improving rate of stirring pin to tensile shear performance is 53.5%, and the improving rate to fatigue performance is 11.4%; the existence of stirring pin in FSSW- B increases the dispersion of joint fatigue properties.
Investigation on friction-stir welding of SS340 steel using a tungsten carbide based stirring tool

Selvam Ramasamy,Saravanan Paramasivam,Omprakasam Subramaniam,Veera Manikandan Paramasivam

DOI: https://doi.org/10.1177/09544089241249832

2024-05-02

Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering

Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. The research focuses on examining the impact of utilizing a tungsten carbide tool on the friction-stir welding procedure used to join two stainless steel plates. This investigation examines the effects of traversal speed and rotation on microstructural alterations in a tungsten carbide tool, with a specific emphasis on weld resistance and creep strength. Stress analysis is used to understand fluctuations in stress levels during the welding process on a stainless-steel workpiece. The investigation aims to determine the impact of welding parameters, specifically welding speed, on the microstructure, hardness distribution, and tensile strength of welded joints. The effectiveness of the friction-stir welding is determined by the correlation between pin diameter and tool shoulder. A Numerical model and analysis of the experiments to understand tool behaviour, considering lateral bearing loads and viscous frictional torsion loads by using ANSYS. The finite element method is used to find stress distribution in stir welding, considering tool parameters. A tungsten carbide tool with a conical pin tool was used under constant conditions: a rotational speed of 325 r/min, a maximum axial load of 11.2 kN, and a welding speed of 10 mm/min. The results showed that the maximum equivalent stress reached 500 MPa when the tool had traversed a distance of 25 mm. These findings provide valuable insights into the stress dynamics of the tool under these specific operating conditions. Different tests are conducted with varying design parameters and pre-hole conditions to understand the stress distribution on the tungsten carbide tool.

engineering, mechanical
Investigation of tool offset on the microstructure and mechanical properties of AA6061-T6/PC Friction Stir Butt Welding joint

Yibo Sun,Wenru Fu,Yuan Zhang,Bo Yu,Haiwei Long,Li Zou,Xinhua Yang

DOI: https://doi.org/10.1177/07316844231219319

IF: 3.1

2023-12-04

Journal of Reinforced Plastics and Composites

Abstract:Journal of Reinforced Plastics and Composites, Ahead of Print. Conventional friction stir welding (FSW) is mostly applied to lap welding, which is suitable to join metal/polymer materials. In this paper, solid-state friction stir butt welding (FSBW) technology is utilized to bond the sheets with the plates of 2 mm thickness of 6061-T6 aluminum alloy (AA6061-T6) and polycarbonate (PC) in a joint design. The effects of tool offset on the temperature evolution, surface morphology, microstructural characteristics, and mechanical properties of the dissimilar joints are investigated. A sound dissimilar join with the average highest tensile strength of around 14.23 MPa is attained at the offset of 3.5 mm. Microstructural characteristics indicate an effective mechanical interlocking structure (Al anchor). The mixed fragments of polymer and metal are formed with a chaotic interface along the joint line, improving the mechanical properties of welding joints. Furthermore, a novel friction stir V shape butt welding (V-FSBW) is proposed to join dissimilar plates. The maximum tensile strength and improvement rate of the V-FSBW joint compared with conventional FSBW are 18.42 MPa and 29.4%, respectively. Results indicate that the tool offset significantly affects the welding joints, and V-FSBW can effectively increase the mechanical properties of the dissimilar AA6061-T6/PC joints.

materials science, composites,polymer science
Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys

C Ganesan,K Manonmani

DOI: https://doi.org/10.1177/09544089211060642

2021-11-30

Abstract:Friction stir welding is a high potential technology for joining similar and dissimilar aluminum materials, utilized extensively in aerospace and automotive industrial applications to eradicate the problems like hot cracking, porosity, element loss, etc. due to the fusion welding process. This Research addresses the joining of two dissimilar materials of AA 5754 – H32 and AA 8090T6511 – Al-Li and their mechanical properties analysis with the effects of friction stir welding process parameters like tool rotational speed, welding speed and axial load on weld nugget zone formation quality. The significant roles of different tool pin profiles are also emphasized. A mathematical modeling equation was formed by using regression analysis to optimize the process parameter and found the best tool pin profile for defect-free weld nugget zone and higher tensile and hardness properties. This research also portrays the contribution of various pin profiles and each process parameter on the ultimate tensile strength by response surface methodology. The results indicate that the defect-free weld joints are observed with 1800 r/min of rotational speed, welding speed of 15 mm min −1 and 8.5 kN of axial load with hexagonal pin profile.
The performance of a Co-based alloy tool in the friction stir welding of TA5 alloy

Shuaishuai Du,Huijie Liu,Minghao Jiang,Li Zhou,Fuyang Gao

DOI: https://doi.org/10.1016/j.wear.2021.204180

IF: 4.695

2022-01-01

Wear

Abstract:A low-cost Co-based alloy was employed to fabricate friction stir welding (FSW) tools to weld TA5 alloy under different welding speeds. The tool wear characteristics, tool degradation mechanisms and effects of tool wear behavior on the microstructure and mechanical properties of joints were investigated in detail. Results reveal that the heat input near weld root decreases with the increase of welding speed and the tool wears more extensively under lower heat input when the deterioration rates of tool sizes are considered. Furthermore, the tool wears out mainly by mechanical abrasion near pin tip, leading to a large number of tool particles in mixed regions accompanied by severe material loss. The tool wears less severely near pin root and shoulder, since the adhesion layer caused by adhesive and diffusional wear mechanisms is the main cross-sectional wear morphology, and the interlayer rich in W and Cr between adhesion layer and intact part of tool may protect the tool from serious diffusional wear. The foreign β-stable tool compositions were introduced to the weld, reducing the transus temperature. Therefore, transformed acicular α and retained β phases were detected in contaminated zone (CZ) inside stir zone (SZ) compared with the untransformed equiaxed α grains in non-contaminated zone (NCZ). In addition, the acicular α and β phases result in much higher strength and microhardness than base material (BM).

engineering, mechanical,materials science, multidisciplinary

[Intraosseous lipomatosis: positivity in bone scintigraphy with 99mTc-HDP].

Experimental and Simulation Investigation on Fatigue Performance of H13 Steel Tools in Friction Stir Welding of Aluminum Alloys

Failure mechanisms of Friction stir welding tools related to process control and tool geometry

Thermal-fluid-structure coupling analysis of void defect in friction stir welding

Comparison of tool wear during friction stir welding of Al alloy and Al-SiC metal matrix composite

Effect of Friction Stir Welding Tool Design on Welding Thermal Efficiency

Effect of tool revolutionary pitch on heat transfer and material flow in Al/steel friction stir lap welding

An Alternative Frictional Boundary Condition for Computational Fluid Dynamics Simulation of Friction Stir Welding

Numerical Simulation of Material Flow Behavior of Friction Stir Welding Influenced by Rotational Tool Geometry

Numerical analysis on the functions of stir tool's mechanical loads during friction stir welding

Study on the Microstructure and Mechanical Properties on Al/Carbon Fiber Reinforced Thermoplastic Dissimilar Friction Stir Lap Welding Joints

A New Tooling Approach for Friction Stir Welding of Thin Sheet AA2024-T3 - Optimization of Welding Parameters

Finite-element Analysis of the Tool Tilt Angle Effect on the Formation of Friction Stir Welds

Study on the influence of tool rotational speeds/welding traverse speeds on the quality and surface formation of 6mm copper friction stir welding

Structural optimization study of stationary shoulder friction stir welding head with non-rigid support

Investigation of Tool Degradation during Friction Stir Welding of Hybrid Aluminum–Steel Sheets in a Combined Butt and Overlap Joint

Effect of Stirring Pin on Interfacial Microstructure and Mechanical Properties of FSSW-B Joint

Investigation on friction-stir welding of SS340 steel using a tungsten carbide based stirring tool

Investigation of tool offset on the microstructure and mechanical properties of AA6061-T6/PC Friction Stir Butt Welding joint

Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys

The performance of a Co-based alloy tool in the friction stir welding of TA5 alloy