Abstract:The interactions among thermal history, plastic deformation and residual stresses in the friction stir welding (FSW) process under different welding parameters have been widely considered a crucial issue and still not fully understood. In the present study, a novel three-dimensional fully coupled thermo-mechanical finite element (FE) model based on coupled Eulerian-Lagrangian approach (CEL) has been developed to simulate the FSW process of aluminium alloy AA 6082-T6 and to analyse the thermo-mechanical interaction mechanisms under different welding conditions. The numerical model successfully simulates the plunge, dwell, and welding steps in FSW and captures the evolution of temperature, plastic deformation, and residual stresses in the welded joint. The obtained results were validated by experimental testing with observed cross-weld thermal history, optical macrography and residual stress measurement using the neutron diffraction technique. The results reveal that the tool rotation speed governs the temperature evolution; the peak temperature increased from 740 to 850 °K when the tool rotation speed rose from 800 to 1100 rpm. The rotational speed also affected the plastic deformation, material flow, and the volume of material being stirred during the welding process. Higher plastic deformation is formed in the stirring zone by increasing the tool angular velocity. This behaviour led to an increase in the stirring effect of the welding tool, reduction of the tunnel defect size and enhancing the quality of weldments. The distribution of residual stresses in different zones of the FSW joints has been found to have an M-shaped profile. A significant tensile residual stress is characterised in the edge of the nugget zone in both longitudinal and transverse directions, balanced by compressive stresses in the thermo-mechanically affected zone, heat-affected zone and base metal. The presented FE modelling provides a reliable insight into the effects of the welding parameters on the weld quality of FSW joints and process optimisation with minimised experimental trials.

Effect of Friction Stir Welding Tool Design on Welding Thermal Efficiency

Effect of Processing Parameters on Welding Temperature During Friction Stir Welding of Aluminum Alloy

Enhancing Mechanical Characteristics of 6061-T6 with 5083-H111 Aluminum Alloy Dissimilar Weldments: A New Pin Tool Design for Friction Stir Welding (FSW)

Experimental and Simulation Investigation on Fatigue Performance of H13 Steel Tools in Friction Stir Welding of Aluminum Alloys

Computational Fluid Dynamics Studies on Heat Generation During Friction Stir Welding of Aluminum Alloy

Effects of Tool Geometry on Friction Stir Welding of AA6061 to TRIP Steel

Temperature-dependent friction coefficient and its effect on modeling friction stir welding for aluminum alloys

Thermal simulation on friction stir welding of AA6061 aluminum alloy by computational fluid dynamics

Heat generation, plastic deformation and residual stresses in friction stir welding of aluminium alloy

The Effect of Tool Geometry on the Strength of FSW Aluminum Thin Sheets

Influence of Friction Stir Processing on Weld Temperature Distribution and Mechanical Properties of TIG-Welded Joint of AA6061 and AA7075

Effect of Friction Stir Welding Parameters on the Impact Energy of the Weldments of Poorly Weldable Aluminum Alloys by Fusion Welding

Effect of Tool Profile Influence in Dissimilar Friction Stir Welding of Aluminium Alloys (AA5083 and AA7068)

The Effect of Tool Rotation on Structure and Mechanical Properties in Friction Stir Welding Of Aluminum AA5052

Effect of tool revolutionary pitch on heat transfer and material flow in Al/steel friction stir lap welding

Effect of Tool Geometries on "Heat-Input" During Friction Stir Welding of Aluminum Alloys

Friction stir welding of aluminium hollow extrusion: weld formation and mechanical properties

Study on the effects of ultrasonic assistance and external heat dissipation on friction stir welded 7075 aluminum alloy joints

Temperature Monitoring and Material Flow Characteristics of Friction Stir Welded 2A14-t6 Aerospace Aluminum Alloy

An Experimental Study On Friction Stir Welding Of Aluminum-Magnesium Alloys For Improved Mechanical Properties Of Tailor Welded Blanks.

Experimental Study on Mechanical Behaviour of Friction Stir Welded Aluminium Alloy Butt Joints