Abstract:Friction stir welding (FSW) is a solid-state welding process commonly used to join similar and dissimilar aluminum alloys. This study aims to investigate multi-criteria decision-making, multi-objective optimization, Taguchi's L9 design of experiments, and the technique for order preference by similarity to the ideal solution (TOPSIS) to evaluate the effects of various FSW parameters specifically, welding speed, feed, and axial load on the mechanical properties of AA5754 aluminum alloy. Following the enhancement of the welding parameters, an analysis of variance (ANOVA) was performed to identify the most influential parameter in the FSW process. The findings indicated that tensile strength, impact strength, and microhardness were predominantly affected by welding speed (94.82%), feed (3.12%), and axial load (1.32%), respectively. With a hexagonal tool and optimal process parameters of feed (20 mm/min), axial load (7 kN), and speed (1200 rpm), the joint obtained the maximum microhardness (81 HV), impact strength (3.01 J/mm 2 ), and tensile strength (163.89 MPa). The microstructure and X-ray diffraction analyses indicated that the crystals were tiny, with higher dislocations in the stir zone, indicating improved mechanical properties. In the FSW joint, dimples and voids were observed on the tensile and impact fracture surfaces. Finally, the ballistic properties of the optimized AA5754 FSW joint were determined. An asymmetric V-shaped deformation profile was observed around the impact point, with the highest deformation at the center. An increase in impact velocity from 134 to 187.6 m/s did not result in significant differences in the deformation of the FSW joint. The fracture surfaces of ballistic-tested friction stir welded joints exhibited shear regions and localized bands.

Effect of Friction Stir Welding Parameters on the Impact Energy of the Weldments of Poorly Weldable Aluminum Alloys by Fusion Welding

The Effect of Tool Rotation on Structure and Mechanical Properties in Friction Stir Welding Of Aluminum AA5052

Tensile and wear behaviour of friction stir welded AA5052 and AA6101-T6 aluminium alloys: effect of welding parameters

Influence of Friction Stir Processing on Weld Temperature Distribution and Mechanical Properties of TIG-Welded Joint of AA6061 and AA7075

Study on the effect of the welding environment on the dynamic recrystallization phenomenon and residual stresses during the friction stir welding process of aluminum alloy

Influence of tool velocity ratio on force-torque and mechanical properties of friction stir welded 2050-T84 Al-Li alloy plates

Welding Investigation on AA6063-T6 Aluminium alloy during Friction Stir Welding process

Influence of Process Parameters on the Mechanical Properties and Corrosion Resistance of Dissimilar Friction Stir Welded Joints of AA2024-O and AA6061-O Aluminum Alloys

Material Flow Behavior and Thermal Cycle during Friction Stir Welding of AA5083/AZ91 Dissimilar Metals

Investigation of Weldability in Friction Stir Welding of Aluminum Alloys AA5754 and AA2024

Analysis of Friction Stir Welded Joint Properties of 2A12 Aluminum Alloy

Optimization of process parameters of friction stir welded joints of dissimilar aluminum alloy by response surface methodology

Effects of parameters on friction stir welding process of AA 7075 aluminum alloy: mechanical and microstructural assessments

Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys

Tool rotational speed impact on temperature variations, mechanical properties and microstructure of friction stir welding of dissimilar high-strength aluminium alloys

Evaluation of axial force, tool torque and weld quality of friction stir welded dissimilar 6061/5083 aluminum alloys

An Experimental Study On Friction Stir Welding Of Aluminum-Magnesium Alloys For Improved Mechanical Properties Of Tailor Welded Blanks.

Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Numerical simulation and experimental research on friction stir welding of 2024-T3 aeronautical aluminum alloy

On the role of input welding parameters on the microstructure and mechanical properties of Al6061-T6 alloy during the friction stir welding: Experimental and numerical investigation