Abstract:In this present work, Ni3Si–Al2O3 nanocomposite powders were synthesized by mechanical milling using NiO, Si and Al as raw materials. The phase transformation, formation mechanism and microstructure evolution of the powders during mechanical milling were investigated by X-ray diffraction (XRD), differential thermal analysis (DTA), scanning electron microscopy (SEM), transition electron microscopy (TEM) and microhardness measurements. Results showed that the Ni3Si, Al2O3 and Ni31Si12 phases formed after 5 h of milling with a rapid mechanically induced self-propagating synthesis mode. The average grain size and internal strain of Ni3Si and Al2O3 after 30 h of milling were (16.8 nm, 1.27%) and (19.6 nm, 0.94%), respectively. The maximum microhardness value of 813 HV was obtained in the 30 h milled powder. The relationship between the hardness and grain size of the powders satisfies the Hall–Petch relationship. Ni3Si–Al2O3 nanocomposite powders are very stable during heating at 950 °C. By annealing of the milled powders leads to grain growth, internal strain and microhardness of Ni3Si powder decrease and transformation of disordered structure to an ordered state. A long-range ordering parameter (LRO) of 0.97 for the ordered Ni3Si can be achieved after annealing at 950 °C for 2 h.

Fabrication of NiO/ZrO2 nanocomposites using ball milling-pyrolysis method

PREPARATION OF NiO NANOPARTICLES ON THE SILICA SURFACE BY ADSORPTION PHASE SYNTHESIS AND ITS REGULATION ON MORPHOLOGY OF NiO PARTICLES

Fabrication of Zno Nanoneedle/Nanocolumn Composite Films and Annealing Induced Improvement in Their Microstructural and Photoluminescence Characteristics

Structure, Surface Nature, Thermal Stability, and Biomass Gasification Process of NiO/SiO2 and NiO-Pr2O3/SiO2 Nanocomposites Obtained through Facile Deposition Precipitation Method

Milling parameter optimization for refinement of NiO/Al mixtures and synthesis of Ni/Al2O3 nanocomposites

Preparation of nano-sized 6MgO–2Y2O3–ZrO2 powders by a combined co-precipitation and high energy ball milling process

Facile Synthesis and Characterization of ZrO₂ Nanoparticles via Modified Co-Precipitation Method

Preparation and Modification of Nano-Zno/ceo2 Composite Oxides

Preparation and characterization of nanocrystalline NiO in mixed solvent

Preparation of One-Dimensional Ni0.5 Zn0.5 Fe2O4/SiO2 Composite Nanostructures and Their Magnetic Properties

ZnO Nanospheres Fabricated by Mechanochemical Method with Photocatalytic Properties

Characterization and Formation Mechanism of Ni3Si–Al2O3 Nanocomposite Prepared by Mechanochemical Reduction Method

Preparation Of Zno Nanoparticles By Precipitation/Mechanochemical Method

Conversion of Conventional NiO Powders into Nanostructures by a Simple Chemical Method

A Simple Ball Milling and Thermal Oxidation Method for Synthesis of ZnO Nanowires Decorated with Cubic ZnO2 Nanoparticles

Zn2MnO4/ZnO nanocomposites: One step sonochemical fabrication and demonstration as a novel catalyst in water splitting reaction

Nano‐Bricks Assembly Toward 1D Metal Oxide Nanorods

Preparation of Composite Nanoparticles of Fe-Zn Bioxide Using Surface Modification and Their Subsequent Characterization

From design to characterization of zirconium nitride/silicon nitride nanocomposites

Co-precipitation of nano Mg–Y/ZrO2 ternary oxide eutectic system: Effects of calcination temperature