Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Sublimation and Recrystallization of CsPbBr 3 Constructing a Perovskite-Carbon Interface to Facilitate Hole Transfer in Printable All-Inorganic Perovskite Solar Cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Scalable In‐Plane Directional Crystallization for The Printable Hole‐Conductor‐Free Perovskite Solar Cell Based on The Carbon Electrode

Insight into the Ch3nh3pbi3/C Interface in Hole-Conductor-Free Mesoscopic Perovskite Solar Cells

In Situ Buried Interface Engineering towards Printable Pb-Sn Perovskite Solar Cells

Constructing an Interfacial Gradient Heterostructure Enables Efficient CsPbI3 Perovskite Solar Cells and Printed Minimodules

Interface Engineering for All‐Inorganic CsPbIBr 2 Perovskite Solar Cells with Enhanced Power Conversion Efficiency over 11%

Interface Modification Via a Hydrophobic Polymer Interlayer for Highly Efficient and Stable Carbon-Based Inorganic Perovskite Solar Cells

Improving Photovoltaic Performance of Carbon-Based CsPbBr3 Perovskite Solar Cells by Interfacial Engineering Using P3HT Interlayer

Buried Interface Modulation via Preferential Crystallization in All‐Inorganic Perovskite Solar Cells: The Case of Multifunctional Ti3C2Tx

Efficient Carbon-Based CsPbBr3 Inorganic Perovskite Solar Cells by Using Cu-Phthalocyanine as Hole Transport Material

Bridging the Buried Interface with Conjugated Molecule for Highly Efficient Carbon-Based Inorganic CsPbI2Br Perovskite Solar Cells Fabricated in Air

Low temperature-processed stable and high-efficiency carbon-based CsPbI2Br perovskite solar cells by additive strategy

Printable CsPbI3 Perovskite Solar Cells with PCE of 19% via an Additive Strategy

A 2D/3D heterojunction engineering for carbon-based hole-transport-layer-free perovskite solar cells

Bridging the buried interface with conjugated molecule for highly efficient carbon-based inorganic CsPbI 2 Br perovskite solar cells fabricated in air

Photovoltaic Performance Improvement of All‐Inorganic CsPbBr3 Perovskite Solar Cells by Antisolvent Assisted Crystallization

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

In Situ Reconstruction Post‐Treatment for Efficient Carbon‐Based Hole‐Conductor‐Free Printable Mesoscopic Perovskite Solar Cells