Abstract:Background: For large mandibular defects, surgical reconstruction using microvascular fibular grafts has advantages over other alternatives in terms of blood supply and good quality of grafted bone. However, the fibular segment is usually lower in height than that of the original mandible, meaning that the vertical positioning of the fibular graft is variable, with different biomechanical consequences on the reconstructed mandible. Objectives: To use finite element method (FEM) to evaluate stress distribution and displacement of a reconstructed mandible versus an intact mandible under occlusal loads. Methods: A three-dimensional intact edentulous mandibular bone (Model I) and a reconstructed mandible bone with fibular graft were created from CBCT images. Calculation models were generated with fibular bone graft extracted from the reconstructed mandible of identical length placed into a mimicked defect area on the right-hand side of the mandible at three different vertical positions: superior (Model II), intermediate (Model III), and inferior (Model IV). Forces were applied at lower left first molar region and lower left central incisor area. Von Mises stresses and mandibular displacement were calculated as outcome measurements during loadings. Results: Maximum stress and strain within the reconstructed mandible were identified at the posterior border of the graft and the contralateral condyle. Maximum displacement occurred near the interface of fibular graft and anterior segment of the mandible. Stress distribution in the graft under functional loads is much higher than that in the residual mandibular segments from Models II to IV. The combined average maximum stress from anterior and posterior loads is 10.66 times higher in the mandible with inferiorly positioned graft (Model IV), 8.72 times for superior graft (Model II), and 3.68 times for intermediate graft (Model III) than that in the control group (Model I). The worst displacement result during functional loadings was in the group with fibular graft located at the inferior border of the mandible. Conclusions: The position of fibular graft placed in the surgical resection site has significant effects on the mechanical behavior of the reconstructed mandible. The fibular graft aligned with the inferior border of the mandible, the most common site designated location by clinicians, has the worst effects on the stress distribution and displacement to the mandibular under functional loads. The fibular graft placed at the intermediate location has the best biomechanics and provides favorable condition for subsequent prosthetic reconstruction.

The comparison between various methods of mandibular reconstruction based on finite element analysis

Mandibular reconstruction system reliability analysis using probabilistic finite element method

Biomechanical Evaluation of Reconstruction Plate for Fixation of Mandibular Prosthesis

Three-dimensional Finite Element Analysis of Mechanical Stress in Symphyseal Fractured Human Mandible Reduced with Miniplates During Mastication

Biomechanical analysis comparing natural and alloplastic temporomandibular joint replacement using a finite element model

Design And Biomechanical Analysis Of A Novel Mandibular Prosthesis

Biomechanical Behavior of the Three-Dimensionally Printed Surgical Plates for Mandibular Defect Reconstruction: a Finite Element Analysis

The Design and Biomechanical Evaluation of Individual Mandibular Prosthesis

Establishment of Sequential Software Processing for a Biomechanical Model of Mandibular Reconstruction with Custom-Made Plate.

[Study of Biomechanical Effects on the Reconstruction of Mandible Defect with Autogenous Bone Grafts].

Biomechanical analysis of mandibular defect reconstruction based on a new base-fixation system

Three-dimensional Finite-Element Analysis Investigating the Biomechanical Effects of Human Mandibular Reconstruction with Autogenous Bone Grafts

Biomechanical behavior of mandibles reconstructed with fibular grafts at different vertical positions using finite element method

[Three-Dimensional Finite Element Analysis of the Mandible Reconstruction with Fibula].

Computational models and their applications in biomechanical analysis of mandibular reconstruction surgery

Biomechanical Comparison of Locking and Non-Locking Patient-Specific Mandibular Reconstruction Plate Using Finite Element Analysis.

Comparison of full‐arch mandibular reconstruction with dental implants using completely splinted or segmentally splinted prostheses with two different occlusal schemes: A finite‐element analysis

Biomechanical finite element analysis of short-implant-supported, 3-unit, fixed CAD/CAM prostheses in the posterior mandible

Influence of bite force and implant elastic modulus on mandibular reconstruction with particulate-cancellous bone marrow grafts healing: An in silico investigation

Biomechanical Three-Dimensional Finite Element Analysis of Prostheses Retained With/without Zygoma Implants in Maxillectomy Patients.

Biomechanical assessment of mandibular fracture fixation using finite element analysis validated by polymeric mandible mechanical testing