Abstract:In-Vessel Retention (IVR) strategy for nuclear reactors in case of a Severe Accident (SA) intends to stabilize and retain the corium in the vessel by using the vessel wall as a heat exchanger with an external water loop. This strategy relies on simple actions to be passively taken as soon as SA signal is raised: vessel depressurization and reactor pit flooding. Then, the strategy is successful if the vessel keeps it integrity, which means that the heat flux coming from the corium pool does not exceed the cooling capacity of the External Reactor Vessel Cooling (ERVC) at each location along the vessel wall (no vessel melt-through) and the ablated vessel wall is mechanically resistant. The main uncertainties in this IVR safety evaluation are associated to the thermal load applied from the corium pool to the vessel wall and the resulting minimum vessel thickness after ablation. Indeed, the heat fluxes distribution along the vessel wall is directly dependent on the corium stratification which occurs as aresult of thermochemical interactions in the pool: when liquid steel is mixed with UO2 and partially oxidized Zr coming from the degradation of the fuel and claddings, there is a phase separation between oxide and metal phases due to a gap of miscibility. The primordial impact of the corium behaviour in the lower plenum of the reactor vessel on the IVR safety evaluation was clearly highlighted in the Phenomena Identification Ranking Table (PIRT) on IVR performed in the frame of the European IVMR (In-Vessel Melt Retention) project (Fichot et al., 2019). As a result, the focus is made in this paper on the critical points which impact the value of the minimum vessel thickness orequivalently the maximum heat flux reached at the outer surface of the vessel wall. Efficiency of the ERVC and mechanical resistance of the vessel wall are consequently not discussed here.The main objective is to identify the generic critical situations leading to an excessive heat flux to the vessel wall and the investigation of possible means to avoid them. In this perspective, the calculations of IVR strategy done by the project partners for different reactor designs and accident scenarios were used as a database to identify and understand the occurrence of critical configurations with excessive heat flux to the vessel wall. The results of 25 sequences are used, which correspond to 9 different reactor designs: a generic PWR 900MWe, a PWR 1100MWe with heavy reflector, a generic PWR 1300MWe, a generic Konvoi 1300MWe, a generic German BWR69, aNordic BWR, a BWR-5 Mark II, a VVER1000 and a VVER440/v213. In addition, different SA integral codes (ASTEC, ATHLET-CD, MAAP -combined with MAAP_EDF and PROCOR codes for simulation of lower plenum behavior-, MELCOR and RELAP/SCDAPSIM codes) are used.

Prolonged Operation of Hydro-Accumulators in VVER-1000/V446 Considering Flow Restriction Components

Re-assessment of accumulators performance to identify VVER-1000 vulnerabilities against various break sizes of SB-LOCA along with SBO

Early Mitigation Measures for High Flux Reactor Loss-of-Coolant Accidents

Safety Analysis in VVER-1000 Due to Large-Break Loss-of-Coolant Accident and Station Blackout Transient Using RELAP5/SCDAPSIM/MOD3.5

Analyses for Passive Safety of Fusion-Reactor During Ex-Vessel Loss-Of-Coolant Accident

Simulation of VVER-1000 Guillotine Large Break Loss of Coolant Accident Using RELAP5/SCDAPSIM/MOD3.5

Analysis of critical points of the In-Vessel Retention safety evaluation

Comprehensive Safety Analysis Code System for Nuclear Fusion Reactors III: Ex-Vessel LOCA Analyses Considering Passive Safety

Analysis of loss of cooling and loss of coolant severe accident scenarios in VVER-1000/V446 spent fuel pool

Thermal Hydraulic Characteristics During Ingress of Coolant and Loss of Vacuum Events in Fusion Reactors

Concrete ablation depth analysis of OPR1000 NPP during top flooding ex-vessel cooling

Research on Compliance Between Large Break LOCA of HPR1000 and New LOCA Acceptance Criterion 10Cfr50.46c

Thermohydraulic Analysis of Accident Scenarios of a Fusion DEMO Reactor Based on Water-Cooled Ceramic Breeder Blanket: Analysis of LOCAs and LOVA

Experimental Research on Influence of Real Surface Material and Aging Effect on ERVC-CHF of RPV

Numerical study on the thermal hydraulic characteristics of ERVC system

Calculations of research reactor thermal hydraulics based on VVER-440 fuel assamblies

In-Vessel Retention of Molten Core Debris for CAP1400

Scaling and Integral Effect Test on Transition from Depressurization to Long-Term Gravity Injection

Investigation of System Responses of the Maanshan Nuclear Power Plant to the Loss of Residual Heat Removal During Midloop Operation Using a RELAP5/MOD3 Simulation

Demonstration of Structural Integrity of Boiling Water Reactor Pressure Vessels under Ultimate Response Guideline Operation

ICONE19-43276 Preliminary Study on In-Vessel Retention in Large-Scale Advanced PWR