Sodium fluoride unmasks the accumulation of lysophosphatidylcholine in intact pancreatic islet cells.

S. Metz,M. Dunlop

DOI: https://doi.org/10.1016/0006-291X(90)91730-G

1990-02-28

Abstract:

What problem does this paper attempt to address?

Investigating parametric effects during TIG welding of dissimilar metals

Abdullah Abdullah,Shahid Mehmood,Rana Atta Ur Rahman

DOI: https://doi.org/10.22581/muet1982.2401.2969

2024-01-01

Mehran University Research Journal of Engineering and Technology

Abstract:This paper explores the optimization of Tungsten-Inert-Gas (TIG) welding process parameters for creating a hybrid structure of Aluminium 6061 and Stainless Steel 304 using a copper filler rod (ER-Cu). The Welding of these two materials has industrial relevance owing to its weight reduction capabilities and environmental benefits. However, Aluminium and Stainless-Steel have different melting points and thermal properties. Aluminium has twice coefficient of thermal expansion and six times coefficient of thermal conductance as compared to Stainless-Steel. This difference often results in residual stresses and brittle intermetallic compounds in the weld region. We have chosen the Welding Current, Welding Speed, and Gas Flow Rate as input parameters, and Ultimate Tensile Strength (UTS) and Micro-hardness as response parameters. We have employed the Response Surface Methodology (RSM) using a Box-Behnken design to evaluate the influence of input parameters on UTS and Micro-hardness. Furthermore, an Analysis of Variance (ANOVA) is conducted to determine the input parameters' significance on the response parameters. Our surface plots demonstrate that UTS improves with increased Welding Current and reduced Welding Speed. Simultaneously, Micro-hardness increases with elevated Welding Speed and decreased current, up to a specific limit. The peak value of UTS (79 MPa) was observed with a Current range of 85-90 A, Speed range of 95-100 mm/min, and Gas Flow Rate of 14.5-15 l/min. On the other hand, maximum Micro-hardness (260HV) was obtained with a Current range of 80-85 A, Speed range of 105-110 mm/min, and Gas Flow Rate of 14.5-15 l/min. This research contributes to improving the manufacturing process of hybrid structures, specifically by optimizing the advantages of both Aluminium and Stainless Steel while addressing the challenges that arise during their combination. The study's conclusions have major consequences for sectors looking to take advantage on the mutually beneficial characteristics of different metals in welding applications.
Study of The Microstructure and Mechanical Property Relationships of Gas Metal Arc Welded Dissimilar Protection 600T, DP450 and S275JR Steel Joints

Mustafa Elmas,Oğuz Koçar,Nergizhan Anaç

DOI: https://doi.org/10.3390/cryst14050477

IF: 2.7

2024-05-20

Crystals

Abstract:The need for combining dissimilar materials is steadily increasing in the manufacturing industry, and the resulting products are expected to always have high performance. While there are various methods available for joining such material pairs, one of the commonly preferred techniques is fusion welding. In this study, three different steel materials (Protection 600T, DP450, and S275JR) were joined using gas metal arc welding (GMAW) in different combinations (similar/dissimilar). The microstructure and mechanical properties of the joints were evaluated. Tensile test, Vickers microhardness (HV 0.1), bending, Charpy V-notch impact testing, and microstructure examinations were conducted to analyze the weld and heat-affected zone. The tensile strengths of the base metal materials Protection 600T, DP450, and S275JR were found to be 1524.73 ± 18.7, 500.8 ± 10.4, and 508.5 ± 9.5 MPa, respectively. In welded samples of similar materials, the highest efficiency was found to be 103.05% for DP450/DP450, while in dissimilar welded joints, it was 105.5% for the DP450/S275JR pair. Hardness values for the base materials Protection 600T, DP450, and S275JR were measured as 526.5 ± 10.5, 153.8 ± 1.8, and 162.5 ± 5.2, respectively. In all welded samples, there was an increase in hardness in the weld zone (due to the welding wire) and the heat-affected zone (due to grain size refinement). While the impact energy values of similar material pairs were close to the base material impact energy values, the impact energy values of dissimilar material pairs varied according to the base materials. In addition, in joints made with similar materials, the bending force was close to the base materials, while a decrease in bending force was observed in joints formed with dissimilar materials. As a result, the welding of DP450 and S275JR materials was carried out efficiently. Protection 600T was welded with other materials, but its welding strength was limited to the strength of the material with low mechanical properties.

materials science, multidisciplinary,crystallography
Effect of Weld Length on Strength, Fatigue Behaviour and Microstructure of Intersecting Stitch-Friction Stir Welded AA 6016-T4 Sheets

Dominik Walz,Robin Göbel,Martin Werz,Stefan Weihe

DOI: https://doi.org/10.3390/ma16020533

IF: 3.4

2023-01-06

Materials

Abstract:Friction stir welding is a promising joining process for boosting lightweight construction in the industrial and automotive sector by enabling the weldability of high-strength aluminum alloys. However, the high process forces usually result in large and heavy equipment for this joining method, which conflicts with flexible application. In order to circumvent this issue, a friction stir welding gun has been developed which is capable of producing short stitch welds—either stand-alone as an alternative to spot welds or merging into each other appearing like a conventional friction stir weld. In this study, the influence of the stitch seam length on the strength properties of intersecting friction stir welds is investigated, and the weld is characterized. For this purpose, EN AW-6016 T4 sheets were welded in butt joint configuration with varying stitch lengths between 2 and 15 mm. Both the static and dynamic strength properties were investigated, and hardness and temperature measurements were carried out. The results show a scalability of the tensile strength as well as the fatigue strength over the stitch seam length, while the substitute proof strength is not affected. Hereby, the tensile strength reached up 80% of the base materials tensile strength with the chosen parameter setup. Likewise, the stitch weld length influences the hardness characteristics of the welds in the transition area.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Comparative Research of Microstructure and Mechanical Properties of Stainless and Structural Steel Dissimilar Welds

Saulius Baskutis,Jolanta Baskutiene,Regita Bendikiene,Antanas Ciuplys,Karolis Dutkus

DOI: https://doi.org/10.3390/ma14206180

2021-10-18

Abstract:The present study utilized a metal inert gas welding (MIG) to make a dissimilar weld of stainless steel AISI 304, 314, 316L, 420 grades and a standard structural steel S355MC. It refers to a weld joining two materials from different alloy systems commonly used in heat exchangers, pressure vessels, and power plant systems. Obviously, maintaining the integrity of such welds is of paramount importance to the safety issues. Therefore, detailed microscopic and experimental studies were performed to evaluate the reliability of these welds. The microscopic analysis did not reveal any presence of weld defects such as porosity or cracks, which ensured that MIG process parameters were properly selected. The performance of dissimilar welds was assessed by hardness and tensile tests. The hardness profiles revealed differences between austenitic and martensitic steel welds that later showed extremely high values in the heat-affected zone (HAZ), which caused fractures in this zone during tensile test. The welds of all austenitic steel grades withstood the tensile test, showing an average tensile strength of 472 MPa with fractures observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.
Material Strength Optimization of Dissimilar MIG Welding between Carbon and Stainless Steels

Hoang Van Huong,Thanh Tan Nguyen,Van-Thuc Nguyen,Van Thanh Tien Nguyen

DOI: https://doi.org/10.3390/met14091011

IF: 2.695

2024-09-04

Metals

Abstract:This study examines the effects of stick-out, welding current, welding speed, and voltage on the mechanical characteristics and microstructure of MIG welding on SUS 304 stainless steel and S20C steel. The Taguchi method was used to maximize the experiment's outcomes. Fine columnar dendrites formed at fusion sites, and δ-ferrite phases with dark lines and shapes accumulated between the fusion line and the austenite phases. A welding current of 110 A, voltage of 15 V, welding speed of 500 mm/min, and stick-out of 12 mm were the optimal settings for the ultimate tensile strength (UTS). The UTS value confirmation was 469.4 MPa, which agrees with the estimated value determined using the Taguchi technique. The tensile test revealed that welding current had a far greater impact on mechanical qualities than welding voltage, speed, and stick-out distance. The ideal welding parameters for flexural strength were as follows: stick-out of 12 mm, arc voltage of 15 V, welding speed of 450 mm/min, and welding current of 110 amp. The Taguchi method is useful, as evidenced by the validation of the flexure strength of 1937.45 MPa, which is much greater than the other samples. The impact of the thermal annealing process on the mechanical characteristics of the dissimilar weld joints could be the subject of future research. The investigation results may offer more insightful information about the dissimilar welding field.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Effect of welding parameters on microstructure and mechanical properties of dissimilar AISI 304/ductile cast iron fusion welded joints

M El-Shennawy,H A Abdel-Aleem,M M Ghanem,A M Sehsah

DOI: https://doi.org/10.1038/s41598-024-70050-0

2024-08-27

Abstract:Problems associated with dissimilar fusion welding are mainly originated from the differences in melting points, coefficients of thermal conductivity and thermal expansion, …etc., and carbon content when welding dissimilar ferrous materials. In this study, the problems associated with dissimilar fusion welding of stainless steel AISI304 with ductile cast iron DCI grade A536 were investigated. Using shielded metal arc welding (SMAW) process, various welding parameters were studied to investigate the successful/accepted dissimilar welded joint(s). Welding electrodes and welding techniques were the main studied parameters. Microstructural and mechanical investigations were carried out for welded joints under different welding parameters. Tensile, impact and hardness tests coupled with optical and scanning electron microscopic examinations with EDX analysis were made for metallurgical and mechanical evaluations of welded joints. This extensive study could solve the problem of dissimilar welding between ductile cast iron and 304 stainless steel. The main results showed that joints welded by ENiCrFe-3 electrode in root pass and ENiFe-CI in filling passes were the successful dissimilar welded joints with 422 MPa tensile strength which represents 104% of annealed DCI base metal and without any changes in toughness properties, where toughness at HAZ of DCI was 18 J. High Ni content in weld metal increased the strength, ductility and reduced the weld metal dilution.
Optimization of gas metal arc welding parameters for dissimilar steel welds: A case study on duplex stainless steel 2205 and stainless steel 316L

Veerakumar Sengottaiyan,Krishnamurthy Kasilingam,Meenakshipriya Balasubramaniam,Arunkumar Munimathan

DOI: https://doi.org/10.1177/09544089241272807

2024-09-04

Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering

Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. The significance of welded connections in steel structures necessitates precise structural designs and processing adaptations to ensure robust mechanical strength and durability. Gas metal arc welding (GMAW) employing controlled curves presents advantages over conventional methods, offering enhanced weld bead properties, improved aesthetics, and reduced thermal inputs. This research investigates the impact of GMAW parameters using controlled curves on the microstructure and geometry of welds between dissimilar structural steels—duplex stainless steel 2205 and stainless steel 316L grade 50—commonly employed in construction. The aim is to optimize the GMAW welding process with controlled curves and surface tension transfer between these dissimilar steels. Through a 23-factorial experimental design encompassing feed speed (Va), arc focus (FC), and peak-to-base amplitude (APB), the study examines welding energy, geometry, deposition efficiency, microstructure, microhardness, tensile strength, and corrosion properties. Optimal welding energy fosters refined microstructures and uniform hardness, aiding in predicting weld throat area. Higher energy levels expand the heat-affected zone and coarse grains, while lower energies escalate variability. Predictive models facilitate fine-tuning welding energy and throat area for desirable properties and penetration while minimizing disruptions. This process optimization can be achieved by employing derived equations that limit welding energy and curve parameters, striking a desired balance between cost, structural integrity, and reliability.

engineering, mechanical
Electrical properties of hafnium silicate films obtained from a single-source MOCVD precursor

M. Lemberger,A. Paskaleva,S. Zürcher,A. Bauer,L. Frey,H. Ryssel

DOI: https://doi.org/10.1016/j.microrel.2004.11.040

2005-05-01

Abstract:
Studies on the Quality of Joints and Phenomena Therein for Welded Automotive Components Made of Aluminum Alloy—A Review

Bogdan Derbiszewski,Andrzej Obraniak,Adam Rylski,Krzysztof Siczek,Marek Wozniak

DOI: https://doi.org/10.3390/coatings14050601

IF: 3.236

2024-05-11

Coatings

Abstract:To fulfill the need to limit automotive emissions, reducing vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle and by the selection of light materials, including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational, and environmental factors. The present study focused on a review of various welding techniques used to join both similar and dissimilar Al alloys utilized in the automotive industry, the effect of various process parameters on weld quality, and the phenomena observed in such welds. The research methodology was based on the analysis of the content of articles from main databases. Apart from capturing the current state of the art, this review evaluates reaching the possible highest joint quality and welding process disadvantages such as porosity, poor surface quality, a tendency toward hot cracking, and low ductility for the Al alloys applied in the automotive industry.

materials science, multidisciplinary, coatings & films,physics, applied
A parametric study on the mechanical properties of MIG and TIG welded dissimilar steel joints

Mehmet Şükrü Adin

DOI: https://doi.org/10.1080/01694243.2023.2221391

IF: 2.431

2023-06-06

Journal of Adhesion Science and Technology

Abstract:In the present day, the joining of dissimilar metals used in the same industry applications is of great interest. MIG and TIG welding processes are among the most common methods used to join dissimilar metals with high strength and reliability. Due to the different mechanical properties of dissimilar metals to be joined by these welding methods and welding parameters, they must be carefully selected. In this study, the effects of Total Accumulated Weld Volumes (TAWV) and different groove angles (45°, 60°, 75° and 90°) on the mechanical properties of AISI 1040 and AISI 8620 cylindrical steel joints were investigated experimentally. In addition, the fracture surfaces of the samples were examined by scanning electron microscopy (SEM) and energy dispersive X-ray (EDAX). In the process with MIG and TIG welding, only current and voltage changes were made in order to measure the effects of parameters on the mechanical properties of the joints more clearly. As a result of the studies, the highest average Ultimate Tensile Strength (UTS) was 579.611 MPa and the lowest average UTS value was 424.611 MPa. Based on TAWVs, the highest average UTS value was obtained in TIG welded joints, and the lowest average UTS value was obtained in MIG welded joints. It was observed that the UTS values of the joints were positively affected by the increase in TAWV. The UTS value of the 90° groove angled joint was found to be 40.25% higher than the UTS value of the 45° groove angled joint.

materials science, multidisciplinary,engineering, chemical,mechanics
Eighth International Workshop on Juris-Informatics (JURISIN 2014)

S. Tojo

DOI: https://doi.org/10.1007/978-3-662-48119-6_16

2014-10-27

Abstract:
Study and effect of GTAW parameters on mechanical properties of aluminium dissimilar welded joints: optimization technique

Abhishek Saxena,Kuldeep K. Saxena,Bharat Singh,S. K. Rajput,Balram Yelamasetti,Yelamasetti, Balram

DOI: https://doi.org/10.1007/s12008-023-01683-0

2023-12-14

International Journal on Interactive Design and Manufacturing

Abstract:In this research, dissimilar metals of AA 6082 and AA 7075 are joined using Gas Tungsten Arc Welding (GTAW) process with ER4043 filler wire. The welding conditions and their range are identified for producing quality welding characteristics. Taguchi based techniques are adopted for design of experimentation and analyzing factors involved in welding characteristics. L-9 Orthogonal Array (OA) was used for Design of Experiments (DOE). Welding current, filler diameter and root gaps are selected as input parameters. The welded structure defects were inspected with X-ray radiography images as well as macrostructures. The response factors such as Ultimate Tensile Strength (UTS), % of elongation, hardness and impact strength were considered and evaluated by conducting mechanical tests. Analysis of Variance (ANOVA) is conducted to study the influence of parameters on responses. The tensile strength of sample 5 is increased by 53.37% when compared with the sample 6 due to the lower heat input rates. The welding speed (68%) has most influence parameter followed by welding current (14%) and filler diameter (14%). The dissimilar combination of aforementioned joints have wide range of application including aerospace, defense, and military sectors.
Friction stir spot welding lap-shear force analysis of automotive low-carbon steel sheets joint

Carlos E C Barbosa,Marcio Batista,Gilmar F Batalha,Rafael H M de Siqueira,Éd C Bordinassi,Adalto Farias,Sergio Delijaicov

DOI: https://doi.org/10.1177/09544089241234553

2024-02-29

Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering

Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. This study aims to provide reference values and outcomes to support the practical implementation of friction stir spot welding in the automotive industry. This study investigated the friction stir spot welding of AISI/SAE 1006 cold-rolled low-carbon steel sheets commonly used in automotive lightweight structural components. Employing a design of experiment-composite central design approach, process parameters like tool rotational speed, plunge depth, and dwell time were examined using a series of experiments. The friction stir spot welding process was conducted using a tungsten carbide M30 tool. The study analyzed the influence of these parameters on mechanical properties such as lap-shear force, axial force, torque, and temperature. Plunge depth showed as a statistically significant factor affecting axial force. Torque demonstrated sensitivity to plunge depth and tool rotational speed, while temperature primarily depended on tool rotational speed. The tool rotational speed and plunge depth combination led to substantial temperature increments, promoting thermal structural transformations, including recrystallization. The analyses of microstructures revealed distinct zones within the welded joint, highlighting the recrystallization phenomena primarily in the mixing zone beneath the tool. The results showed satisfactory mechanical joint quality with ductile failure modes. No significant correlation was found between the lap-shear force and the dependent parameters. The selected range of variables and the chosen tool profile suggest a viable approach for producing friction stir spot welding joints in low-carbon steel and a robustness of the process in achieving an average tensile lap-shear force of 7.48 ± 0.64 kN, surpassing the minimum specification stipulated in the American National Standard AWS D8.1 M, which is 1.5 kN. This finding highlights the complex nature of the friction stir spot welding process, suggesting that other factors beyond the investigated parameters may influence the lap-shear force and indicate the potential to achieve even higher tensile stress values in lap joints by exploring alternative parameter combinations.

engineering, mechanical
Optimization of parameters in rotary friction welding process of dissimilar austenitic and ferritic stainless steel using finite element analysis

Anas Abid Mattie,Safeen Yaseen Ezdeen,Gawhar Ibraheem Khidhir

DOI: https://doi.org/10.1177/16878132231186015

IF: 2.1

2023-07-08

Advances in Mechanical Engineering

Abstract:Advances in Mechanical Engineering, Volume 15, Issue 7, July 2023. Solid state joining techniques are increasingly used in joining different types of materials, in this work TP347HFG austenitic stainless steel will be welded with HiPerFer ferritic stainless-steel alloy due to their similarity in their properties to some extent after making heat treatment to ferritic alloy in addition to difference in their cost which save for economic reasons. In this work, a three-dimensional finite element model was developed. The thermal analysis and profiles between process parameters were predicted by using an ANSYS software tool. Design of experiments by Anova was used to examinate the simulation results and to evaluate contribution ratio of each parameter on responses, while grey relational analysis was used to specify the optimum trial. It was observed that trial 11 give best results (A4B2C1D1) which got higher grey relational grade. It was concluded that the friction pressure and friction time have more impact on interface temperature, whereas forging pressure and friction time affect the equivalent Von-Mises stress directly. The speed and forging pressure have a more influence on total deformation. It was also concluded that the temperature was fade out by diverging toward the end of specimen and the amount of decrease in temperature is less in ferritic side. The amount of flash extruded from both steels are approximately similar due to similarity in properties as heat treatment of ferritic alloy had been achieved. The investigation results show that trial 8 achieved highest Von-Mises stress (300 MPa) while trial 7 induced lower stress (255 MPa), maximum deformation was found equivalent to 0.012 mm with trial 16 whereas, it was found (0.008 mm) with trial 11 which were both less than the allowable deformation in end application. Tensile strength of weld joint was found equivalent to 80% of softer base metal. The hardness of optimum trial was equivalent to 156 HB.

engineering, mechanical,thermodynamics
Modeling and Optimization of Friction Stir Welding Parameters for Joining Dissimilar Aluminum Alloys

Mohamed Mohamed Abd Elnabi,Abou Bakr Elshalakany,A. Mokadem,T. Osman

DOI: https://doi.org/10.21467/AJGR.4.1.1-14

2018-04-04

Abstract:The objectives of this work are to optimize the process parameters on the mechanical properties (ultimate tensile strength (UTS) and ductility) of dissimilar joints between AA5454 and AA7075 produced by friction stir welding and to determine which of them is significant by using Taguchi L16 optimization method. Seven parameters at two levels were selected in this study. The selected parameters are tool rotational speed, traverse speed, pin profile (based on taper angle), D/d ratio, tool tilt angle, plunge depth, and base metal location. Then, mathematical models are built as function of significant parameters/ interactions using Response Surface Methodology. The results of this work showed that the rotational speed, traverse speed, D/d ratio and plunge depth are significant parameters in determining UTS (Mean, Signal to noise ratio (S/N)) at different confidence levels, but pin profile, location of base metal and tool tilt angle are insignificant parameters at any confidence levels. The traverse speed has the highest contribution to the process for UTS about 18.577 % and 16.943 % for S/N ratio and mean, respectively. The accuracy of the models according to the UTS is 97.678 % and 99.56 %for mean and S/N ratio, respectively. The maximum joint efficiency, compared to the strength of the AA5454, is 85.3%.

Engineering,Materials Science
Study the effect process of parameters on friction welding of dissimilar metals AISI 304 steel and AA 2219 aluminium

G. Ananda Rao,B. Rohith Kumar,G. Nithin Kumar,P. Mahender,T. Uday Kumar

DOI: https://doi.org/10.1063/5.0036450

2021-01-01

Abstract:Friction welding is a solid state welding process to produce the joint by utilizing heat generated by friction at the interface and with axial pressure. Friction welding process is non consumable and reusable in manufacturing process. This method produces the joint between similar and dissimilar metals without much effecting heat affected zone. The conventional welding technique is very difficult to join dissimilar metals as they are differing in their thermal and metallurgical properties. Welding of dissimilar metals is very much interested in automotive, aerospace and other industrial applications. The aluminium alloy in combination with steel bodies has significant reduction in weight and cost saving. In this present work a continuous drive friction welding process was performed on dissimilar material AA2219 aluminium alloy and AISI 304 austenitic stainless steel. The study was carried on process parameters like rotational speed, Heating Pressure, Upsetting Pressure, Heating time, and Upset time that are influenced on friction welding process. The experiment was conducted for different combination of process parameter to identify the optimal. The strength of the welded joints is varied with heating pressure and increasing with upset pressure at constant upset time and friction time. The welded joints strength was examined with tensile strength and was tabulated. The hardness distribution at the joint interface was noted and plotted a hardness peak was observed at interface. Micro structural observation was also done characterize the joint. It was observed that burn of length is one parameter that plays vital role on wastage metal in the welding process.
Microstructure and Fatigue Properties of Resistance Element Welded Joints of DP500 Steel and AW 5754 H22 Aluminum Alloy

Aleksija Đurić,Dragan Milčić,Zijah Burzić,Damjan Klobčar,Miodrag Milčić,Biljana Marković,Vladislav Krstić

DOI: https://doi.org/10.3390/cryst12020258

IF: 2.7

2022-02-14

Crystals

Abstract:The modern concept of lightweight design (LW) requires the application of different materials in one structure (multi-material structures). The structure of different materials has a good perspective for application in the automotive and aerospace industries but only if it is possible to achieve a quality joint between different materials. The most used technology for joining different materials in the automotive industry is Resistance spot welding (RSW). Due to different mechanical, physical, and chemical properties, the joining of different materials by RSW technology does not provide a quality joint, and accordingly, alternative technologies for joining different materials have emerged. Resistance element welding (REW) was developed to enable joint of different materials. This paper presents the welding of AW 5754 H22 Al alloy (1.0 mm-thick) and DP500 steel (1.5 mm-thick) using novel REW. The peak load, absorption energy, microstructure, microhardness and fatigue strength of the REW joint has been investigated. The joint of the same materials has been done also using conventional RSW to compare some results. The results that will be presented in this paper show that that REW can achieve reliable joining of the two materials at relatively low welding currents compared to RSW. Using REW process with a significantly lower welding current, satisfactory mechanical characteristics of the weld joint can be achieved, so peak load is between 2300–2500 N, displacement is between 2.5–3 mm and the absorption energy is between 3.3–5.7 J. REW joints showed fatigue strength with the fatigue limit of 882 N.

materials science, multidisciplinary,crystallography
Development of mechanical property prediction model and optimization for dissimilar aluminum alloy joints with the friction stir welding (FSW) process

Yodprem Pookamnerd,Panuwat Thosa,Sittichai Charonerat,Suriya Prasomthong

DOI: https://doi.org/10.21303/2461-4262.2023.002776

2023-05-25

Abstract:Friction stir welding (FSW) is a solid-state joining process used to weld dissimilar aluminum alloys with varying material properties and compositions. Unlike traditional welding methods, FSW does not involve melting the materials being welded but instead uses a rotating tool to heat and stir the materials until they are in a plastic state. The process results in a welded joint with high strength, excellent ductility, and minimal distortion, making it a popular choice in various industries, including aerospace, automotive, and marine. AA6061-T6 (Mg-Si) and AA7075 (Al-Zn-Mg-Cu) aluminum alloys are one of the most popular grades of aluminum alloys used in current manufacturing industries, such as aerospace and automotive, joined by the Friction Stir Welding Process (FSW) technique. Taguchi orthogonal array (L9) experimental design was applied to reduce the number of insignificant factors in the process. First, the study determines three welding factors: rotation speed, travel speed, and pin eccentricity. Investigations found that travel speeds significantly on tensile strength (Ts) and elongation ( %El), but the rotational speed and tool eccentricity did not affect Ts and %El. Furthermore, considering the fabricated parameters on the hardness (HV) of the joint, it was found that all factors unaffected the HV of the joint zone at a 95 % confidence level. Next, examine the microstructure; Mg2Al3 and Al2O3 intermetallic compounds were found in the weld. Therefore, investigating the crystallite size found that welding significantly affects the crystallite size. Finally, consider the fracture surface, experimental condition A2B1C2 (optimal parameter), which is the parameter with the highest tensile strength having dimple fracture characteristics. On the other hand, the welding condition A1B3C3, the parameter with the lowest tensile strength, Small and fine dimple fracture with cleavage fracture. Because the material is highly ductile and can undergo large deformations before it is damaged. On the other hand, materials with low tensile strength exhibiting cleavage fracture indicate that the materials are brittle and can break easily under stress

English Else
Dissimilar Al/steel friction stir welding lap joints for automotive applications

D. Campanella,P. Russo Spena,G. Buffa,L. Fratini

DOI: https://doi.org/10.1063/1.4963499

2016-01-01

AIP Conference Proceedings

Abstract:A widespread usage of aluminum alloys for the fabrication of car-body parts is conditional on the employment of appropriate welding methods, especially if dissimilar welding must be performed with automotive steel grades. Dissimilar welding of aluminum alloys and steel grades poses some issues concerning the formation of brittle intermetallic compounds, difference in physical and chemical properties of the parent metals, and poor wetting behavior of aluminum. Friction stir welding is considered to be a reasonable solution to obtain sound aluminum/steel joints. A study on the join quality of dissimilar lap joints of steel and aluminum alloy sheets after friction stir welding is proposed here. A low carbon steel is joined with AA6016 aluminum alloy to study preliminarily the feasibility to assembly car-body parts. The joints, welded with tool rotation and feed rate varying in a wide range, have been studied from a visual examination and microstructural point of view. Optical microscopy has been used to characterize the microstructure of the examined sheets in as-received and welded conditions. Micro-hardness measurements have been carried out to quantitatively analyze the local hardness of the welded joints. Set welding process parameters are identified to assemble without the presence of macroscopic defects the examined steel and aluminum welded parts.
Effect of ultrasonic welding parameters on microstructure and mechanical properties of dissimilar joints

M. Shakil,N.H. Tariq,M. Ahmad,M.A. Choudhary,J.I. Akhter,S.S. Babu

DOI: https://doi.org/10.1016/j.matdes.2013.09.074

2014-03-01

Abstract:Ultrasonic spot welding has received significant attention during past few years due to their suitable applications in comparison to conventional fusion welding techniques. Fusion welding of dissimilar Aluminum and Stainless steel alloys is always a challenging task because of poor control on grain size and formation of undesirable brittle intermetallic compounds in the weld metal, which have deleterious effect on mechanical properties. In the past, welding of dissimilar alloys has been performed using electron beam welding, laser beam welding and friction stir spot welding, resistance spot welding, etc. However, little work has been reported on dissimilar welding of Aluminum and Stainless steel alloys using ultrasonic spot welding. The objective of the present work is to optimize ultrasonic spot welding parameters for joining 3003 Aluminum alloy with 304 Stainless steel. Welding was performed at various clamping pressures (i.e. 30, 40, 50 and 60psi) and energy levels for investigating its effect on microstructure, mechanical properties and bond quality of the weld. Different levels of weld quality i.e. ‘under weld’, ‘good weld’ and ‘overweld’ were identified at various welding parameters using physical attributes. The weld specimens prepared with energy 125 and 150J showed the maximum bond strength and were rated as “good” weld. It was also revealed that for a good quality weld, the maximum tensile strength is achieved once a reasonable amount of bond density and material thinning (required for the formation of metallurgical bonds) is attained.

materials science, multidisciplinary

Sodium fluoride unmasks the accumulation of lysophosphatidylcholine in intact pancreatic islet cells.

Investigating parametric effects during TIG welding of dissimilar metals

Study of The Microstructure and Mechanical Property Relationships of Gas Metal Arc Welded Dissimilar Protection 600T, DP450 and S275JR Steel Joints

Effect of Weld Length on Strength, Fatigue Behaviour and Microstructure of Intersecting Stitch-Friction Stir Welded AA 6016-T4 Sheets

Comparative Research of Microstructure and Mechanical Properties of Stainless and Structural Steel Dissimilar Welds

Material Strength Optimization of Dissimilar MIG Welding between Carbon and Stainless Steels

Effect of welding parameters on microstructure and mechanical properties of dissimilar AISI 304/ductile cast iron fusion welded joints

Optimization of gas metal arc welding parameters for dissimilar steel welds: A case study on duplex stainless steel 2205 and stainless steel 316L

Electrical properties of hafnium silicate films obtained from a single-source MOCVD precursor

Studies on the Quality of Joints and Phenomena Therein for Welded Automotive Components Made of Aluminum Alloy—A Review

A parametric study on the mechanical properties of MIG and TIG welded dissimilar steel joints

Eighth International Workshop on Juris-Informatics (JURISIN 2014)

Study and effect of GTAW parameters on mechanical properties of aluminium dissimilar welded joints: optimization technique

Friction stir spot welding lap-shear force analysis of automotive low-carbon steel sheets joint

Optimization of parameters in rotary friction welding process of dissimilar austenitic and ferritic stainless steel using finite element analysis

Modeling and Optimization of Friction Stir Welding Parameters for Joining Dissimilar Aluminum Alloys

Study the effect process of parameters on friction welding of dissimilar metals AISI 304 steel and AA 2219 aluminium

Microstructure and Fatigue Properties of Resistance Element Welded Joints of DP500 Steel and AW 5754 H22 Aluminum Alloy

Development of mechanical property prediction model and optimization for dissimilar aluminum alloy joints with the friction stir welding (FSW) process

Dissimilar Al/steel friction stir welding lap joints for automotive applications

Effect of ultrasonic welding parameters on microstructure and mechanical properties of dissimilar joints