Abstract:3D-printed adsorbents are gaining increased attention owing to their potential in overcoming operational challenges faced by the conventionally structured counterparts. In this work, cylindrical scaffolds of triply periodic minimal surface (TPMS) configuration were synthesized using 3D-printing by stereolithography. This unique gyroid sheet TPMS network was selected as it offers a high surface-area-to-volume ratio. The surface of the scaffolds was modified by a silanization process followed by coating via grafting with zeolite 13X crystals toward CO 2 adsorption application. A secondary zeolite coating step was also employed to enhance the zeolite 13X loading, resulting in zeolite loadings of 16 wt% and 23 wt% after the primary and secondary coatings, respectively. Following morphological and structural characterization, the CO 2 adsorption performance of the 3D-printed materials was evaluated with respect to adsorption capacity, kinetics, selectivity, and heat of adsorption. Cyclic stability was also assessed over CO 2 adsorption–desorption pressure swing adsorption cycles at 25 °C. Comparative analysis showed that the 3D-printed coated samples exhibited higher CO 2 /N 2 selectivity and improved cyclic stability with a slightly lower CO 2 adsorption capacity than the zeolite 13X powder. The heat of adsorption ranged from 18 to 41 kJ mol −1 for both the powder and the coated adsorbents, indicating physisorption. The gyroid lattice of the 3D-printed structures, featuring a densely arranged network of smooth, interconnected flow channels, facilitated molecular transport thus yielding higher CO 2 adsorption kinetics than the powder. Indicatively, the primary and secondary coatings attained an equilibrium capacity of 4 mmol g −1 at 25 °C in 62 and 57 min, respectively, while the powder required 110 min at the same conditions. The 3D-printed materials exhibited also significantly higher CO 2 /N 2 selectivity values of 569 and 115 at 50 mbar and 1 bar, respectively, for the primary coating sample, and 536 and 73 at 50 mbar and 1 bar, respectively, for the secondary coating one. The findings highlight the potential of 3D-printing to produce coated structured adsorbents with complex geometries for sustainable CO 2 capture and gas adsorption processes.

Zeolite/Polymer Composites Prepared by Photopolymerization: Effect of Compensation Cations on Opacity and Gas Adsorption Applications

Photopolymerization of Zeolite Filler‐Based Composites for Potential 3D Printing Application and Gas Adsorption Applications

Synthesis and CO2 Capture Behavior of Porous Cross-Linked Polymers Containing Pendant Triazole Groups

Preparation of zeolite-based porous materials via photopolymerization and their applications in 3D printing and gas storage

Fabrication Of Metal-Organic Framework/Polymer Composites Via A One-Pot Solvent Crystal Template Strategy

Nanoscale Features of Zeolite Fillers Enhance the Depth of Cure, Optical Properties, and Mechanical Properties of 3D-Printed Polymer Composite Structures

Photopolymerization of ceramic/zeolite reinforced photopolymers: Towards 3D/4D printing and gas adsorption applications

Structured Zeolite Monoliths with Ultrathin Framework for Fast CO2 Adsorption Enabled by 3D Printing

Zeolite Imidazolate Framework Membranes on Polymeric Substrates Modified with Poly(vinyl Alcohol) and Alginate Composite Hydrogels.

High-Performance Zeolite Naa Membranes on Polymer-Zeolite Composite Hollow Fiber Supports

Zeolite-coated 3D-printed gyroid scaffolds for carbon dioxide adsorption

Exploring the confinement of polymer nanolayers into ordered mesoporous silica using advanced gas physisorption

Synthesis of geopolymer-zeolite composite from municipal solid waste incineration fly ash and their performance for CO 2 adsorption

Controlled polymerization in mesoporous silica toward the design of organic-inorganic composite nanoporous materials.

Novel activated carbon route to low-cost geopolymer based porous composite with high mechanical resistance and enhanced CO2 capacity

Zeolite fillers for resin-based composites with remineralizing potential

Structure–property correlations for composite hydrogels based on poly(methacrylic acid) and high concentrations of LTA zeolite

High-efficiency pentafluorostilbene-based photocatalysts dedicated to preparing fluorescent 3D printed polymer nanocomposites

Photoactive Resin Formulations and Composites for Optical 3D and 4D Printing of Functional Materials and Devices

Effect of Water-Soluble Polymers on the Rheology and Microstructure of Polymer-Modified Geopolymer Glass-Ceramics

Vat photopolymerization 3D printing of yttria-stabilized ZrO 2 ceramics: effects of a sintering additive (Na 2 O ̶ 2SiO 2 ), biocompatibility, and osteointegration