Abstract:Geopolymers are regarded as zeolite-like structure materials but do not exhibit satisfactory zeolite-like capabilities because of their limited porosity and surface area. Geopolymer-zeolite composites have been prepared by embedding zeolite powders into the geopolymer matrix or through the in-situ hydrothermal route, however, it is challenging to obtain both the sufficient mechanical resistance as well as porosity. In this study, a novel activated carbon route was proposed for the first time to overcome the above drawbacks via a facile two-step reaction of activated carbon embedded polycondensation and hydrothermal crystallization. The initiative incorporation of activated carbon into the geopolymer generated an interface in the matrix and improved the porosity of the composite simultaneously, the mechanical resistance loss caused by the interface was effectively mitigated by increasing the alkalinity of the activator. The hydrothermal product exhibited an enhanced specific surface area of 256.24 m2/g due to the improvement of zeolite yields with the aid of the deliberate interface. The hydrothermal zeolite formation process didn't affect the mechanical resistance because the zeolite in the matrix was combined with the geopolymer through [SiO4]4- and [AlO4]5- tetrahedral by sharing the bridging oxygens. This finally resulted in an excellent compressive strength of 23.1 MPa and enhanced CO2 capacity of 60.14 cc/g at 1 atm and 35 °C, both of which are higher than those of geopolymer-based adsorbents reported for CO2 capture to date.

What problem does this paper attempt to address?

### Problems the paper attempts to solve This paper aims to solve the following two key problems: 1. **Improve the balance between the mechanical strength and porosity of porous materials**: - **Background**: Traditional geopolymers have good mechanical strength and chemical stability, but their porosity and specific surface area are low and cannot meet the requirements for efficient CO₂ adsorption. Although the methods of embedding zeolite powder into the geopolymer matrix or synthesizing geopolymer - zeolite composites by in - situ hydrothermal method can increase the porosity, it is difficult to maintain sufficient mechanical strength at the same time. - **Challenge**: How to significantly increase the porosity and specific surface area of the material without sacrificing mechanical strength in order to enhance its CO₂ adsorption capacity. 2. **Develop low - cost and efficient CO₂ adsorption materials**: - **Objective**: By introducing a new preparation method, that is, using activated carbon (AC) as an interface - forming agent and combining the advantages of geopolymers and zeolites, a ternary composite material (ACGZ) with high mechanical strength and high porosity is prepared, so as to achieve efficient and economical CO₂ capture. ### Solutions To solve the above problems, the author proposes an innovative two - step reaction method: 1. **First step: Polycondensation reaction with activated carbon embedded**: - Mix activated carbon with geopolymer precursors and generate an activated carbon - geopolymer composite (ACG) through polycondensation reaction. The presence of activated carbon not only increases the porosity of the material but also forms new interfaces in the geopolymer matrix, and these interfaces are helpful for the subsequent growth of zeolite crystals. 2. **Second step: Hydrothermal crystallization treatment**: - Subject ACG to hydrothermal treatment to convert the geopolymer into zeolite in - situ on the surface of activated carbon, and finally form an activated carbon - geopolymer - zeolite ternary composite (ACGZ). This composite not only retains relatively high mechanical strength but also significantly increases the specific surface area and porosity, thereby enhancing the CO₂ adsorption capacity. ### Main achievements - **Mechanical strength**: The finally obtained ACGZ composite exhibits excellent compressive strength (23.1 MPa), which is higher than that of pure geopolymers and other composites. - **Porosity and specific surface area**: The specific surface area of ACGZ reaches 256 m²/g, much higher than that of pure geopolymers and ordinary composites. - **CO₂ adsorption capacity**: The CO₂ adsorption capacity of ACGZ at 1 atm and 35 °C reaches 60.14 cc/g, which is better than other geopolymer - based adsorbents reported so far. In conclusion, this research successfully solves the balance problem between mechanical strength and porosity of geopolymer - based materials by introducing activated carbon as an interface - forming agent, and develops a low - cost and efficient CO₂ adsorption material.

Novel activated carbon route to low-cost geopolymer based porous composite with high mechanical resistance and enhanced CO2 capacity

Synthesis and CO2 Capture Behavior of Porous Cross-Linked Polymers Containing Pendant Triazole Groups

Synthesis, characterization, and selective CO2 capture performance of a new type of activated carbon-geopolymer composite adsorbent

Synthesis of geopolymer-zeolite composite from municipal solid waste incineration fly ash and their performance for CO 2 adsorption

Robust structure regulation of geopolymer as novel efficient amine support to prepare high-efficiency CO2 capture solid sorbent

Structurally Designed Synthesis of Mechanically Stable Poly(benzoxazine-co-resol)-Based Porous Carbon Monoliths and Their Application As High-Performance CO2 Capture Sorbents

Facile Synthesis of MOF-5-derived Porous Carbon with Adjustable Pore Size for CO2 Capture

Combined granulation–alkali activation–direct foaming process: A novel route to porous geopolymer granules with enhanced adsorption properties

Facile, Low-Cost, and Sustainable Preparation of Hierarchical Porous Carbons from Ion Exchange Resin: an Improved Potassium Activation Strategy

Novel Superadsorbent from Pozzolan-Charcoal based Geopolymer Composite for the Efficient Removal of Aqueous Crystal Violet

Application of CO2-loaded geopolymer in Zn removal from water: A multi-win strategy for coal fly ash disposal, CO2 emission reduction, and heavy metal-contaminated water treatment

A Novel Strategy to Enhance the Performance of CO2 Adsorption Separation: Grafting Hyper-cross-linked Polyimide onto Composites of UiO-66-NH2 and GO

Porous carbon frameworks with high CO2 capture capacity derived from hierarchical polyimide/zeolitic imidazolate frameworks composite aerogels

Imidazolium salt-modified porous hypercrosslinked polymers for synergistic CO2 capture and conversion

Building Metal-functionalized Porous Carbons from Microporous Organic Polymers for CO2 Capture and Conversion under Ambient Conditions

A Novel Coal Gasification Coarse Slag-Based Geopolymer: Influences of Physico-Chemical Coupling Activation on Its Properties, Microstructure, and Hazardous Material Immobilization

In situ fabrication and characterization of graphene/geopolymer composites

Cleaner geopolymer prepared by co-activation of gasification coal fly ash and steel slag: durability properties and economic assessment

Facile synthesis of porous geopolymers via the addition of a water-soluble pore forming agent

Calcium carbide residue and Glauber's salt as composite activators for fly ash-based geopolymer

A novel amine functionalized porous geopolymer spheres from municipal solid waste incineration fly ash for CO2 capture