Abstract:With additive manufacturing (AM) processes such as Wire Arc Additive Manufacturing (WAAM), components with complex shapes or with functional properties can be produced, with advantages in the areas of resource conservation, lightweight construction, and load-optimized production. However, proving component quality is a challenge because it is not possible to produce 100% defect-free components. In addition to this, statistically determined fluctuations in the wire quality, gas flow, and their interaction with process parameters result in a quality of the components that is not 100% reproducible. Complex testing procedures are therefore required to demonstrate the quality of the components, which are not cost-effective and lead to less efficiency. As part of the project "3DPrintFEM", a sound emission analysis is used to evaluate the quality of AM components. Within the scope of the project, an approach was being developed to determine the quality of an AM part dependent not necessarily on its geometry. Samples were produced from WAAM, which were later cut and milled to precision. To determine the frequencies, the samples were put through a resonant frequency test (RFM). The unwanted modes were then removed from the spectrum produced by the experiments by comparing it with FEM simulations. Later, defects were introduced in experimental samples in compliance with the ISO 5817 guidelines. In order to create a database of frequencies related to the degree of the sample defect, they were subjected to RFM. The database was further augmented through frequencies from simulations performed on samples with similar geometries, and, hence, a training set was generated for an algorithm. A machine-learning algorithm based on regression modelling was trained based on the database to sort samples according to the degree of flaws in them. The algorithm's detectability was evaluated using samples that had a known level of flaws which forms the test dataset. Based on the outcome, the algorithm will be integrated into an equipment developed in-house to monitor the quality of samples produced, thereby having an in-house quality assessment routine. The equipment shall be less expensive than conventional acoustic equipment, thus helping the industry cut costs when validating the quality of their components.

Small Specimen Technology for Revealing Mechanical Properties of Alloys, 3D-Printing Metals and Welding Joints

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

Semi-automatic miniature specimen testing method to characterize the plasticity and fracture properties of metals

A review of selected small specimen test techniques for identifying deformation and failure properties of metallic materials

Surface Patterning for Multi-Scale Strain Analysis of In-Situ Sem Mechanical Experiments

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

A Miniaturized Device Coupled with Digital Image Correlation for Mechanical Testing

Mechanical Properties Study of Miniature Steel Specimens Based on the Small Punch Test and Simulation Methods

Mechanics of the small punch test: a review and qualification of additive manufacturing materials

Metals by micro-scale additive manufacturing: comparison of microstructure and mechanical properties

Ultrasonic nondestructive characterization and its role in the development and implementation of additive manufacturing processes

On the investigation of microstructure and mechanical properties of the AlCoCrFeNi 2.1 /316 L dissimilar spot-welded joint

On the Investigation of Microstructure and Mechanical Properties of the AlCoCrFeNi2.1/316 L Dissimilar Spot-Welded Joint

Design and Application of a Miniature Pneumatic Bellows Loading Device for In-Situ Tensile Testing inside the Scanning Electron Microscope

Rapid Quantification of Dynamic and Spall Strength of Metals Across Strain Rates

In Situ Investigation of Tensile Response for Inconel 718 Micro-Architected Materials Fabricated by Selective Laser Melting

A large-volume 3D EBSD study on additively manufactured 316L stainless steel

Miniature Tensile and Small Punch Testing: Mechanical Performance and Application in Hydrogen Embrittlement Analysis

A Smart, Data-Driven Approach to Qualify Additively Manufactured Steel Samples for Print-Parameter-Based Imperfections

In situ SEM fatigue testing technology for metallic materials: a review

Novel miniature in situ hole expansion test coupled with microscopic digital image correlation