Abstract:Background: Trans- inferior alveolar nerve (IAN) implantation technique was wildly used while the potential appropriate angle range in which the residual alveolar bone can bear the stress without absorption are currently unclear. This study aimed to evaluate the stress distribution pattern of the interface between bone and implant by finite element analysis (FEA) to determine the appropriate range of the implant tilt angle. Methods: Cone beam computed tomography (CBCT) images of 120 patients with missing mandibular second molars and vertical bone height < 9 mm in the edentulous area were selected. The distances from the mandibular nerve canal to the buccal cortex, the lingual cortex and the alveolar ridge crest were measured by using a combination of software. The angular ranges of the buccal-lingual inclination of simulated trans-IAN implants were measured and three-dimensional finite element models were constructed in the mandibular second molar area according to the differences of the inclination angles. A vertical load (200N) was then applied to analyze the biomechanical conditions of the implant-bone interface during median occlusion. Results: The distance at the second molar from the nerve canal to the buccal cortex, lingual cortex and alveolar crest were 6.861 ± 1.194 mm, 2.843 ± 0.933 mm and 7.944 ± 0.77 mm. Trans-IAN implantation was feasible in 73.33% of patients. The minimum angle and maximum angles of the buccal-lingual inclination of the simulated implant were 19.135 ± 6.721° and 39.282 ± 6.581°. When a vertical static load of 200N was applied, the tensile stress in cortical bone gradually increased with the increase of the implant tilt angle. When the inclination angle reached 30°, the tensile stress (105.9 MPa) exceeded the yield strength (104 MPa) of cortical bone. Compared with the conventional implants, the stress peak value of the vertical ultra-short implant in cortical bone was greater than the stress peak value of the conventional implants at 10°(79.81 MPa) and 20°(82.83 MPa) and was smaller than the stress of the implant at 30°(105.9 MPa) and 40°(107.8 MPa). Therefore, when the bone mass allows, conventional-length implants should be selected whenever possible, and an operative range of the trans-IAN implantation in the mandibular second molar could be retained with an inclination angle of < 30°. Conclusions: The mandibular nerve canal at the mandibular second molar was obviously biased to the lingual side, which ensured sufficient bone mass at the buccal side. In most patients with severe mandibular atrophy, it was possible to maintain a safe distance from the nerve canal with conventional-length implants via the trans-IAN implantation technique.

Radiological evaluation of inferior alveolar nerve displacement after removal of impacted mandibular third molars prior to sagittal split osteotomy

Endoscopic Visualization of the Inferior Alveolar Nerve Associated with Somatosensory Changes after Impacted Mandibular Third Molar Extraction.

Radiographic predictors of post-operative inferior alveolar nerve injury in mandibular third molar surgery

Do anatomical variations of the mandibular canal pose an increased risk of inferior alveolar nerve injury after third molar removal?

Investigation of the relationship between the mandibular third molar teeth and the inferior alveolar nerve using posteroanterior radiographs: a pilot study

Sensitivity of the Inferior Lip and Chin following Mandibular Bilateral Sagittal Split Osteotomy Using Piezosurgery

Retrospective evaluation of sensory neuropathies after extraction of mandibular third molars with confirmed "high-risk" features on cone beam computed topography scans

Degree of Compression of the Inferior Alveolar Canal on Cone-Beam Computed Tomography and Outcomes of Postoperative Nerve Injury in Mandibular Third Molar Surgery

Risk assessment of inferior alveolar nerve injury after wisdom tooth removal using 3D AI-driven models: A within-patient study

Intraoperative Computed Tomography in Bilateral Sagittal Split Osteotomy

Radiographic features of anatomic relationship between impacted third molar and inferior alveolar canal on coronal CBCT images: risk factors for nerve injury after tooth extraction

Morphometric Evaluation of the Alveolar Bone Around Central Incisors During Surgical Orthodontic Treatment of High-Angle Skeletal Class III Malocclusion

Identifying the Anatomical Variations of the Inferior Alveolar Nerve with Magnetic Resonance Imaging

Evaluation of the Linear Relationship of the Inferior Alveolar Nerve Canal to the Lateral Cortex and the Alveolar Crest in the Posterior Mandible: A Computed Tomographic Study

Changes in the Inferior Alveolar Nerve Following Sagittal Split Ramus Osteotomy in Monkeys: A Comparison of Monocortical and Bicortical Fixation

Finite element analysis of the angle range in trans-inferior alveolar nerve implantation at the mandibular second molar

Influence of Inferior Alveolar Nerve Exposure During Sagittal Split Osteotomy on the Rate and Timing of Baseline Sensory Recovery.

Evaluating the Risk Factors of Inferior Alveolar Nerve Injury Following Removal of the Mandibular Third Molars

Evaluating the Risk of Post-Extraction Inferior Alveolar Nerve Injury Through the Relative Position of the Lower Third Molar Root and Inferior Alveolar Canal.

Comparison of Digital OPG and CBCT in Assessment of Risk Factors Associated with Inferior Nerve Injury during Mandibular Third Molar Surgery

A CBCT Based Three-Dimensional Assessment of Mandibular Posterior Region for Evaluating the Possibility of Bypassing the Inferior Alveolar Nerve While Placing Dental Implants.