Abstract:Background: Trans- inferior alveolar nerve (IAN) implantation technique was wildly used while the potential appropriate angle range in which the residual alveolar bone can bear the stress without absorption are currently unclear. This study aimed to evaluate the stress distribution pattern of the interface between bone and implant by finite element analysis (FEA) to determine the appropriate range of the implant tilt angle. Methods: Cone beam computed tomography (CBCT) images of 120 patients with missing mandibular second molars and vertical bone height < 9 mm in the edentulous area were selected. The distances from the mandibular nerve canal to the buccal cortex, the lingual cortex and the alveolar ridge crest were measured by using a combination of software. The angular ranges of the buccal-lingual inclination of simulated trans-IAN implants were measured and three-dimensional finite element models were constructed in the mandibular second molar area according to the differences of the inclination angles. A vertical load (200N) was then applied to analyze the biomechanical conditions of the implant-bone interface during median occlusion. Results: The distance at the second molar from the nerve canal to the buccal cortex, lingual cortex and alveolar crest were 6.861 ± 1.194 mm, 2.843 ± 0.933 mm and 7.944 ± 0.77 mm. Trans-IAN implantation was feasible in 73.33% of patients. The minimum angle and maximum angles of the buccal-lingual inclination of the simulated implant were 19.135 ± 6.721° and 39.282 ± 6.581°. When a vertical static load of 200N was applied, the tensile stress in cortical bone gradually increased with the increase of the implant tilt angle. When the inclination angle reached 30°, the tensile stress (105.9 MPa) exceeded the yield strength (104 MPa) of cortical bone. Compared with the conventional implants, the stress peak value of the vertical ultra-short implant in cortical bone was greater than the stress peak value of the conventional implants at 10°(79.81 MPa) and 20°(82.83 MPa) and was smaller than the stress of the implant at 30°(105.9 MPa) and 40°(107.8 MPa). Therefore, when the bone mass allows, conventional-length implants should be selected whenever possible, and an operative range of the trans-IAN implantation in the mandibular second molar could be retained with an inclination angle of < 30°. Conclusions: The mandibular nerve canal at the mandibular second molar was obviously biased to the lingual side, which ensured sufficient bone mass at the buccal side. In most patients with severe mandibular atrophy, it was possible to maintain a safe distance from the nerve canal with conventional-length implants via the trans-IAN implantation technique.

Evaluation of the Linear Relationship of the Inferior Alveolar Nerve Canal to the Lateral Cortex and the Alveolar Crest in the Posterior Mandible: A Computed Tomographic Study

The study of mandibular alveolar nerve canal by cone-beam computed tomography

Configuration of the inferior alveolar canal as detected by cone beam computed tomography

Assessing the Prevalence and Length of the Anterior Loop of Inferior Alveolar Nerve and the Position and Dimension of Mental Foramen Using Cone Beam Computed Tomography

Degree of Compression of the Inferior Alveolar Canal on Cone-Beam Computed Tomography and Outcomes of Postoperative Nerve Injury in Mandibular Third Molar Surgery

The Mandibular Canal. A Study to Determine if Cortical Bone Exists as a Protective Roof for the Inferior Alveolar Nerve

A CBCT Based Three-Dimensional Assessment of Mandibular Posterior Region for Evaluating the Possibility of Bypassing the Inferior Alveolar Nerve While Placing Dental Implants.

Evaluation of the Possible Relationship between the Curvature and Horizontal Course of the Inferior Alveolar Canal

Identification of the Incisive Branch of the Inferior Alveolar Nerve of Edentulous Mandibles Using Cone Beam Computed Tomography

Identifying the Anatomical Variations of the Inferior Alveolar Nerve with Magnetic Resonance Imaging

Correlation Between Anatomic Structure of the Inferior Alveolar Nerve Canal and Dental Implantation

Available bone morphology and status of neural structures in the mandibular interforaminal region: three-dimensional analysis of anatomical structures

Anatomic Study of the Position of the Mandibular Canal and Corresponding Mandibular Third Molar on Cone-Beam Computed Tomography Images

Anatomical relationship between mental foramen, mandibular teeth and risk of nerve injury with endodontic treatment

Comparison of Digital OPG and CBCT in Assessment of Risk Factors Associated with Inferior Nerve Injury during Mandibular Third Molar Surgery

Can a panoramic radiograph predict the inferior alveolar nerve canal's position, or canal compression, near third molar root apices?

Comparison of panoramic radiograph and cone beam computed tomography findings for impacted mandibular third molar root and inferior alveolar nerve canal relation

Finite element analysis of the angle range in trans-inferior alveolar nerve implantation at the mandibular second molar

Identification of the Incisive Branch of the Inferior Alveolar Nerve of Edentulous Mandibles Using Cone-Beam Computerized Tomography

Inferior alveolar nerve injury resulting from different implant rotary instruments: an ex vivo comparative study in human cadaveric mandibles.

Cone-Beam Computed Tomography Study of Incisive Canal and Maxillary Central Incisors in Dravidian Population