Distance diagnosis in pediatric cardiology: a model for telemedecine implementation.

A. Cloutier

2000-06-01

Abstract:

What problem does this paper attempt to address?

Effect of simulated gastric acid exposure on the hardness, topographic, and colorimetric properties of machinable and pressable zirconia-reinforced lithium silicate glass-ceramics

Abdulaziz Alhotan,Razan Alaqeely,Hanan Al-Johani,Shahad Alrobaish,Sarah Albaiz

DOI: https://doi.org/10.1016/j.prosdent.2024.06.021

IF: 4.148

2024-07-14

Journal of Prosthetic Dentistry

Abstract:Statement of problem The effects of gastric acid on the hardness, topographic, and colorimetric properties of zirconia-reinforced lithium silicate glass-ceramics (ZLSs) for dental restorations remain unknown. Purpose The purpose of this in vitro study was to investigate the effect of simulated gastric acid exposure on the microhardness, surface roughness, color stability, and relative translucency of ZLSs. Material and methods Two pressable ZLSs (VITA AMBRIA, VA and Celtra Press, CP) and 2 machinable ZLSs (VITA Suprinity, VS and Celtra Duo, CD)(n=64) were randomly allocated to artificial saliva (control) or gastric juice immersion groups simulating 10 and 20 years of clinical exposure. Microhardness (Hv) was measured with a Vickers hardness device, and surface roughness (Sa) was recorded with an optical profilometer. The color stability (ΔE 00 ) and relative translucency parameter (RTP) were measured with a spectrophotometer. Data for Hv, Sa, and RTP were analyzed by repeated 2-way ANOVA, and data for ΔE 00 were analyzed by 2-way ANOVA. Post hoc comparisons were obtained from Tukey HSD and Student t tests (α=.05). Results Machinable ZLSs exhibited greater Hv after the simulated gastric acid challenge than pressable ZLSs. Sa was significantly impacted by material type ( P= .001), storage media ( P= .050), and their interaction ( P< .001). ΔE 00 was significantly affected by the type of simulated aging media ( P <.001). After 20 years of simulated gastric acid aging, all ZLS materials surpassed the ΔE 00 perceptibility threshold but did not exceed the ΔE 00 acceptability threshold. VS displayed significantly lower RTP than other ZLS materials at all time points ( P <.001). Conclusions The topographic and colorimetric characteristics of ZLS were significantly altered by exposure to simulated gastric acid.

dentistry, oral surgery & medicine
Impact of Gastric Acid Induced Surface Changes on Mechanical Behavior and Optical Characteristics of Dental Ceramics

Aditi Kulkarni,James Rothrock,Jeffery Thompson

DOI: https://doi.org/10.1111/jopr.12716

Abstract:Purpose: To test the impact of exposure to artificial gastric acid combined with toothbrush abrasion on the properties of dental ceramics. Earlier research has indicated that immersion in artificial gastric acid has caused increased surface roughness of dental ceramics; however, the combined effects of acid immersion and toothbrush abrasion and the impact of increased surface roughness on mechanical strength and optical properties have not been studied. Materials and methods: Three commercially available ceramics were chosen for this study: feldspathic porcelain, lithium disilicate glass-ceramic, and monolithic zirconium oxide. The specimens (10 × 1 mm discs) were cut, thermally treated as required, and polished. Each material was divided into four groups (n = 8 per group): control (no exposure), acid only, brush only, acid + brush. The specimens were immersed in artificial gastric acid (50 ml of 0.2% [w/v] sodium chloride in 0.7% [v/v] hydrochloric acid mixed with 0.16 g of pepsin powder, pH = 2) for 2 minutes and rinsed with deionized water for 2 minutes. The procedure was repeated 6 times/day × 9 days, and specimens were stored in deionized water at 37°C. Toothbrush abrasion was performed using an ISO/ADA design brushing machine for 100 cycles/day × 9 days. The acid + brush group received both treatments. Specimens were examined under SEM and an optical microscope for morphological changes. Color and translucency were measured using spectrophotometer CIELAB coordinates (L*, a*, b*). Surface gloss was measured using a gloss meter. Surface roughness was measured using a stylus profilometer. Biaxial flexural strength was measured using a mechanical testing machine. The data were analyzed by one-way ANOVA followed by Tukey's HSD post hoc test (p < 0.05). Results: Statistically significant changes were found for color, gloss, and surface roughness for porcelain and e.max specimens. No statistically significant changes were found for any properties of zirconia specimens. Conclusions: The acid treatment affected the surface roughness, color, and gloss of porcelain and e.max ceramics. The changes in translucency and mechanical strength for all materials were not statistically significant. Zirconia ceramic showed resistance to all treatments.
Effect of different surface treatments on optical, colorimetric, and surface characteristics of a lithium disilicate glass-ceramic

Felipe Nascimento Brescansin,Catina Prochnow,Luís Felipe Guilardi,Cornelis Johannes Kleverlaan,Ataís Bacchi,Luiz Felipe Valandro,Gabriel Kalil Rocha Pereira

DOI: https://doi.org/10.1111/jerd.12793

Abstract:Objective: To evaluate the effect of surface treatments on optical, colorimetric, and surface characteristics of lithium disilicate glass-ceramic. Materials and methods: Specimens (n = 5, IPS e.max CAD) were randomly allocated to the following treatments: mirror-polished: SiC papers; as-cut: mimicking CAD-CAM milling; ground: 90-120 μm-grit diamond bur; ground polished: ground, finished (46-30 μm-grit diamond bur), polished (diamond cups, brush and diamond paste); ground glazed: ground, glazed; ground polished glazed: association of methods. CIELAB color coordinates were obtained by a spectrophotometer. CIEDE2000 color differences (ΔE00 ) and the translucency parameter (TP00 ) were calculated. Light transmittance was assessed with a colorimeter. Surface characteristics (topography and roughness) were analyzed. Statistical differences for each condition and outcome were detected using one-way ANOVA with Tukey's post-hoc test (α = 0.05). Results: TP00 data show statistical reduction after grinding (p < 0.05), which was only restored with polishing (solely or with glazing). ΔE00 shows that grinding results in perceptible variations in color (above 0.81), which were restored after all post-processing protocols (exception to only glaze application in contact with a black background). Light transmittance data corroborated such performance. Polishing and glazing reduced roughness and improved surface topography. Conclusion: Grinding statistically increased roughness, reduced translucency, light transmittance through the ceramic, and resulted on color differences. On contrary, polishing (followed or not by glazing) reduced roughness and enhanced ceramic translucency and light transmittance. Glaze also reduced roughness, but it still presented reduced translucency. The positioning (facing up or down) of the ceramic treated surface influenced the considered outcomes. Clinical significance: Grinding with diamond burs results in a deleterious impact to the optical, colorimetric and surface characteristics of lithium disilicate ceramic. Thus, polishing (followed or not by glazing) is recommended for optical and topographical enhancements when lithium disilicate monolithic restorations require occlusal adjustments.
Surface Roughness Examination of Glass Ionomer Restorative Cements Treated with Acidic and Basic Pediatric Medications: An In Vitro Study

Zainab R Hasan,Noor R Al-Hasani,Ali I Ibrahim

DOI: https://doi.org/10.4103/jispcd.jispcd_212_23

2024-08-27

Abstract:Background: Consumption of different types of beverages and liquid drugs can affect of the surface properties of restorative material. This may lead to an increased probability of dental caries and periodontal inflammation. Aim: This study evaluated and compared the effect of amoxicillin suspension (AMS) and azithromycin suspension (AZS) on the surface roughness (SR) of silver-reinforced glass ionomer (SGI) and nano resin-modified glass ionomer (NGI). Material and methods: Thirty disks (2 mm height × 4 mm diameter) of each glass ionomer (GI) type were prepared and subdivided into three groups (n = 10), which were separately exposed to AMS, AZS, and artificial saliva (AS). SR was evaluated by atomic force microscopy before and after three-immersion protocols repeated over a 3-week duration with 2-day intervals. In each protocol, the GI samples were exposed weekly to AMS three times daily, AZS once daily, and a full day to AS. Results: This study demonstrated, for the first time, the effect of a basic drug (AZS) on the SR of GIs. Intra- and inter-group comparisons showed significant changes (P ˂ 0.05) in the SR pattern of the GIs after immersion cycles in AZS, AMS, and AS. However, the acidic medication (AMS) exhibited significantly higher changes in SGI than in NGI. Conclusions: The SR of NGIs and SGIs can be significantly affected by the use of AMS and AZS suspensions. SGI demonstrated higher SR deterioration than NGI after immersion cycles in AMS.
Barriers to maternal health service use in Chikhwawa, Southern Malawi.

C. Kambala,T. Morse,S. Masangwi,P. Mitunda

DOI: https://doi.org/10.4314/MMJ.V23I1.67673

2011-03-01

Abstract:INTRODUCTION Research was conducted to get a community's perspective on the factors contributing to continued maternal and neonatal deaths. The aim of the study was to identify and understand experiences, perceptions and needs of the community on maternal health service utilization. METHODS Qualitative data was obtained through focus group discussions with community leaders, women, men and youth in the catchment areas of three remote health centres. A total of fourteen focus groups were held: three each with community leaders, men, women, boys and two with girls. Data was transcribed and analyzed manually through the use of thematic analysis. RESULTS The discussions revealed the following as barriers to maternal health service utilization: walking long distances to access health facilities, lack of midwives, lack of or insufficient items to be used during delivery, long stay and rude health personnel. Seeking help from Traditional Birth Attendants (TBAs) during delivery was a common option because TBAs are within reach, do not demand many items for delivery, and treat the women with respect. CONCLUSION This study suggests some factors that are contributing to the high burden of maternal deaths in Malawi. Interventions should be developed and implemented to improve the barriers reported.
Effect of Glazing Protocol on the Surface Roughness and Optical Properties of Lithia-Based Glass-Ceramics

Amanda Maria de Oliveira Dal Piva,Nina Storm van Leeuwen,Lucas Saldanha da Rosa,Cornelis Johannes Kleverlaan,João Paulo Mendes Tribst

DOI: https://doi.org/10.3390/coatings14060668

IF: 3.236

2024-05-25

Coatings

Abstract:Background: New lithia-based glass–ceramics, including Advanced Lithium Disilicate (ALD), have become popular in dentistry. However, it is unclear if glazing protocols for ALD might compromise its surface or optical properties. Thus, evaluating color and translucency changes in ALD and traditional lithium disilicate (LD) is crucial. Methods: This study aimed to assess how different firing protocols affect the surface and optical properties of LD and ALD. Sixty disc-shaped specimens were prepared, divided into three subgroups based on firing protocols, and subjected to surface roughness analysis. Specimens were immersed in coffee, wine, and water for 7 days, and then brushed. Color and translucency were measured. Results: Firing protocols significantly influenced surface roughness in LD (0.09–1.39 μm) and ALD (0.05–0.88 μm). Color differences were observed in both LD and ALD after 7 days, with visible changes within clinically acceptable thresholds. Translucency remained stable across firing protocols and staining liquids. Conclusions: Varying firing protocols impact surface roughness and color stability in LD and ALD. Despite differences, color and translucency changes remained within acceptable clinical thresholds, suggesting both materials are suitable for dental applications. Therefore, this study reinforces the reliability and versatility of these materials in restorative dentistry.

materials science, multidisciplinary, coatings & films,physics, applied
Staining and bleaching susceptibility of zirconia-reinforced lithium silicate glass-ceramics with different thicknesses, translucencies, and fabrication methods

Hanan Al-Johani,Abdulaziz Alhotan,Saleh Alhijji,Nick Silikas,Julian Satterthwaite

DOI: https://doi.org/10.1016/j.prosdent.2024.01.002

IF: 4.148

2024-01-24

Journal of Prosthetic Dentistry

Abstract:Statement of problem The influence of different thicknesses, translucencies, and fabrication methods on the spectrophotometric and topographical properties of zirconia-reinforced lithium silicate glass-ceramics (ZLSs) for dental restorations remains unclear. Purpose The purpose of this in vitro study was to investigate the effect of thicknesses, translucencies, and fabrication methods on the color stability, translucency parameter, opalescence parameter, whiteness stability, transmitted irradiance, light transmittance, opacity, gloss, and roughness of ZLSs exposed to coffee staining and bleaching treatments. Material and methods Two pressable ZLSs (VITA AMBRIA, VA and Celtra Press, CP) and 2 machinable ZLSs (VITA Suprinity, VS and Celtra Duo, CD) were examined at high translucency (HT) and low translucency (LT) levels in 2 thicknesses (n=160). The specimens were evaluated at baseline, after coffee staining, and after bleaching. The color stability (ΔE2000), translucency parameter (TP), opalescence parameter (OP), whiteness index (WI D ), and whiteness stability (ΔWI D ) were measured with a spectrophotometer. Transmitted irradiance (I t ), light transmission (T), and opacity (O) were obtained from a light-polymerizing unit and a polymerization light collection device. Roughness stability (ΔSa%) was determined with an optical profilometer, and gloss stability (ΔGU%) was recorded with a gloss meter. Data of ΔCIE2000, ΔWI D , ΔSa%, and ΔGU% were analyzed by 4-way ANOVA, and data of the TP, OP, WI D , I t , T, and O were analyzed by repeated 4-way ANOVA (α=.05). Results VS-HT exceeded the ΔCIE2000 acceptability threshold after coffee staining and bleaching protocols. Pressable ZLSs exhibited greater color stability than machinable ZLSs. The 1-mm-thick VA, CP, and CD materials exceeded the ΔWI D perceptibility threshold after bleaching. The highest TP and OP was displayed by the 1-mm-thick CP after bleaching. ΔGU increased after water storage and decreased after coffee staining and bleaching. ΔSa% significantly increased after bleaching ( P <.05). Conclusions The color stability and other spectrophotometric properties of ZLSs depended on material thickness. The effects of ZLS fabrication methods and translucency levels on their measured properties were inconsistent. Subjecting 1-mm-thick ZLS materials to acidic media adversely impacted their stainability and surface texture.

dentistry, oral surgery & medicine
Erwin Uehlinger und Herwig Hamperl 70 Jahre alt

H. Götze,W. Doerr

DOI: https://doi.org/10.1007/BF00542671

Virchows Archiv

Abstract:
Regularization of linear ill-posed problems by the augmented Lagrangian method and variational inequalities

Klaus Frick,M. Grasmair

DOI: https://doi.org/10.1088/0266-5611/28/10/104005

2012-04-03

Abstract:We study the application of the augmented Lagrangian method to the solution of linear ill-posed problems. Previously, linear convergence rates with respect to the Bregman distance have been derived under the classical assumption of a standard source condition. Using the method of variational inequalities, we extend these results in this paper to convergence rates of lower order, both for the case of an a priori parameter choice and an a posteriori choice based on Morozov’s discrepancy principle. In addition, our approach allows the derivation of convergence rates with respect to distance measures different from the Bregman distance. As a particular application, we consider sparsity promoting regularization, where we derive a range of convergence rates with respect to the norm under the assumption of restricted injectivity in conjunction with generalized source conditions of Hölder type.
Impact of glazing on wear, fracture load, and optical properties of a new fully crystallized lithium disilicate ceramic material

Ahmed Mahmoud Fouda,Bogna Stawarczyk,Mutlu Özcan,Lamia Singer,Christoph Bourauel

DOI: https://doi.org/10.1016/j.jmbbm.2023.106102

Abstract:Objectives: Lithium disilicate (LDS) based glass ceramics are indispensable materials in the field of prosthetic dentistry due to their strength and excellent esthetics. Recently, novel fully crystallized LDS for the milling process have been introduced to the market, requiring only chairside polishing before delivery. Since limited data is available about subjecting this material to glazing, this study aimed to evaluate the wear properties, fracture resistance, and optical properties of the newly introduced fully crystallized LDS after glazing. Methods: Lithium disilicate glass-ceramics (fully crystallized (LiSiCAD) and partially crystallized types (EmaxCAD), of shade A3, were used in the present study. The fully crystallized specimens were subjected to a glazing firing cycle in a furnace (LiSiCAD-G) and compared to a polished fully crystallized counterpart (LiSiCAD-P, negative control) and a glazed partially crystallized LDS (EmaxCAD, positive control). Rectangular-shaped ceramic specimens (n = 10, 12 × 6.5 × 1.5 mm) and enamel antagonists were used to test the wear resistance in a specially designed wear machine built at the Department of Oral Technology, University of Bonn, Germany. The volumetric enamel loss of antagonists was measured by means of overlapping virtual 3D models derived from micro-CT scans for the teeth before and after the wear test. The weight loss of ceramic specimens in milligrams was measured after 100,000 and 200,000 wear cycles. A spectrophotometer was used to calculate the CIELAB color parameters of the ceramic specimens against black and white backgrounds to measure the translucency. Fracture resistance was also assessed after thermodynamic fatigue using a universal testing machine until fracture at a 1 mm/min crosshead speed. Statistical analysis was performed using one-way ANOVA and the significance level was set at α = 0.05. Results: EmaxCAD and LisiCAD-G groups showed significantly higher mean ceramic weight loss after 100,000 cycles (2 ± 0.3 mg and 1.93 ± 0.2 mg, respectively) than LisiCAD-P group (0.78 ± 0.19 mg). Glazed LiSiCAD specimens demonstrated significantly higher ΔE values from shade A3 compared to polished LiSiCAD. There was no significant difference in ΔE between LiSiCAD-G and EmaxCAD. For fracture resistance, no significant difference was observed between LiSiCAD-G and LiSiCAD-P before or after aging. Conclusions: The glazed fully crystallized LDS was superior to the partially crystallized one with regard to wear resistance but showed more color changes than the polished fully crystallized one. Furthermore, polishing of fully crystallized LDS could still be considered a better option than glazing when aesthetics is a primary prerequisite.
Effect of repeated firing on the topographical, optical, and mechanical properties of fully crystallized lithium silicate-based ceramics

Hanan Al-Johani,Julfikar Haider,Nick Silikas,Julian Satterthwaite

DOI: https://doi.org/10.1016/j.prosdent.2024.01.006

IF: 4.148

2024-01-21

Journal of Prosthetic Dentistry

Abstract:Statement of problem The influence of different firing protocols on the topographical, optical, and mechanical properties of fully crystallized computer-aided design and computer-aided manufacturing (CAD-CAM) lithium silicate-based glass-ceramics (LSCs) for dental restorations remains unclear. Purpose The purpose of this in vitro study was to investigate the effect of different firing regimens on the surface roughness, gloss, Martens hardness, indentation modulus, biaxial flexural strength, and crystalline structure of fully crystallized CAD-CAM LSCs and the effect of their interposition on the irradiance of a light-polymerization unit. Material and methods Three fully crystallized CAD-CAM LSC blocks were evaluated (N=150): lithium disilicate (Initial LiSi Blocks; LS), zirconia-reinforced silicate (Celtra Duo; CD), and lithium aluminum disilicate (CEREC Tessera; CT). Specimens were allocated to 5 subgroups according to their firing protocol. LSC roughness (Sa) was measured with an optical profilometer, and gloss (GU) was detected with a gloss meter. Martens hardness (HM) and indentation modulus (E IT ) data were obtained from a hardness testing machine. The irradiance of a light-polymerization unit and transmittance of LSCs were measured with an instrument (Managing Accurate Resin Curing-Light Collector; BlueLight analytics, Inc) subsequent to ceramic interposition. Crystalline phases were analyzed by X-ray diffraction, and biaxial flexural strength (σ) was determined by the ball-on-3-ball method in a universal testing machine followed by Weibull analysis to calculate characteristic strength (σ 0 ) and Weibull modulus (m). Two-way ANOVA and Tukey HSD post hoc tests (α=.05) were used to analyze the data. Results Statistically significant differences were found among different treatment groups based on Sa, GU, HM, and E IT values ( P <.001). Delivered irradiance was significantly reduced following CT ( P <.01) and glazed LSC ( P <.005) interposition. CD displayed highest biaxial flexural strength and reliability after 1 firing cycle (σ=568.2 MPa, m=16.8) Conclusions The type of material and firing regimens had a significant effect on the topographical, optical, and mechanical properties of fully crystallized CAD-CAM LSCs. Glazing significantly reduced delivered irradiance, Martens hardness, and biaxial flexural strength.

dentistry, oral surgery & medicine
Suicide among the young--the size of the problem.

N. Madge,J. Harvey

DOI: https://doi.org/10.1006/JADO.1998.0207

1999-02-01

Abstract:It is widely recognized that official suicide rates conceal the real scale of non-accidental self-injurious fatal behaviour, including among children and young people. There are many reasons for this including the constraints of registration policy and practice, uncertainty about the circumstances surrounding a death, an unwillingness-often for the family's sake-to affix a suicide label on a child, and perhaps the belief that the term "suicide" is not quite accurate. The present study examined all records over a 17-year period from an inner London coroner's office in order to make some quantitative assessment of the extent to which non-accidental self-injurious deaths might be underestimated by suicide returns among those under 20 years. It is suggested on the basis of this examination that the real rate of what might be termed "suicide" among this group may be up to three times the official recorded level. This finding received general confirmation from a smaller-scale comparison in an out of London location.
Optimal Hydrofluoric Acid Etching Duration and Impact of Silane/Adhesive on Profilometric Properties and Bonding to Lithium Disilicate Glass Ceramics

T S Porto,A J Faddoul,S J Park,V P Feitosa,T F Eyüboğlu,M Ozcan

DOI: https://doi.org/10.2341/24-015-L

2024-09-01

Abstract:Objectives: This study aimed to assess the surface roughness, surface free energy (SFE), and shear bond strength (SBS) on a lithium disilicate glass-ceramic surface following varying etching protocols (time variation) and application of silane either with or without adhesive material. Methods and materials: Lithium disilicate glassceramic (LDGC) computer-aided design and computer-aided manufacture (CAD/CAM) blocks were cut using a slow-speed cutting mechanism. CAD/CAM blocks were then evaluated for surface roughness, 6 groups (n=20); SFE,12 groups (n=5); and SBS, 10 groups (n=10). The cut CAD/CAM blocks were randomly allocated to 28 groups. Groups were based on the following: 30 or 90 seconds of etching with 9% hydrofluoric acid (HF); application or absence of silane coupling agent (Sil); and application or absence of adhesive (Adh).The control group (Cont) had untreated surfaces. Unetched surfaces were surveyed with only silane (Sil), only adhesive (Adh), or silane+adhesive (SilAdh). Further etched groups were HF30 with HF for 30 seconds, HF30-Sil, HF30-Adh, and HF30-SilAdh. Alternative 90-second etching times produced similar groups: HF90, HF90-Sil, HF90-Adh, and HF90-SilAdh. A digital profilometer was used to assess the surface roughness of specimens, and two readings were recorded. Sessile drop analysis was used to examine SFE specimens, and the OWRK model was modified to measure liquid surface tension. A universal testing machine (UltraTester, Ultradent Products, Inc, South Jordan, UT, USA) was utilized for the SBS test, with the crosshead speed set at 0.5 mm/min until failure. Representative treated specimens from each group were submitted to surface morphological evaluation and chemical analysis using scanning electron microscopy/energy dispersive x-ray spectroscopy (SEM/EDXS) (n=3). After data collection, evaluation using one- or two-way analysis of variance and the post-hoc Tukey test (α=5%) was conducted. Results: A longer etching time of 90 seconds produced a rougher surface. After the 90-second etching process, SFE displayed the greatest values; nevertheless, the use of silane did not affect SFE. For every group examined, the application of silane followed by adhesive resulted in an increase in SBS and more stable bonding over time. SEM/EDXS showed that etching times did affect the amount of cerium on the surface and altered surface morphology. Conclusions: Higher and more consistent bond strengths have been observed with longer etching periods. Silane and adhesive application on the ceramic surface showed stronger and enhanced bond strength, specifically when longer etching times were employed.
Mechanical, Adhesive and Surface Properties of a Zirconia-Reinforced Lithium Silicate CAD/CAM Ceramic Exposed to Different Etching Protocols

Fabián Murillo-Gómez,José Roberto Hernández-Víquez,José Roberto Sauma-Montes de Oca,Cristina Vargas-Vargas,Natalia González-Vargas,José Roberto Vega-Baudrit,Daniel Chavarría-Bolaños

DOI: https://doi.org/10.3390/ma17205039

IF: 3.4

2024-10-16

Materials

Abstract:The aim of this investigation was to evaluate the effect of etching protocols on bond strength, surface roughness, and mechanical properties of a zirconia-reinforced lithium silicate (ZLS) CAD/CAM-ceramic. In total, 100 bars (ISO 6872), 75 plaques, and 25 cubes were cut from ZLS blocks(Vita Suprinity®). The surfaces were standardized, crystallized and divided into five groups: 1. control (no/treatment-C), 2. 5%-Hydrofluoric-acid (HF)/20 s (HF5%20s), 3.HF5%60s, 4.HF10%20s, and 5.HF10%60s. Flexural strength (FS) (three-point bending test, 1 mm/min), roughness (Pa), and micro-shear bond-strength (μSBS) tests were performed. The data were statistically analyzed with one-way ANOVA, Tukey's test (p ˂ 0.05) and Weibull (FS data). C showed higher Pa (1.176 ± 0.370 μm) than HF10%60s (0.627 ± 0.236 μm) and all other groups. Groups C and 20 s showed the most irregular surface patterns. The FS results were not influenced by etching protocols, while the Weibull modulus was, with the 5%HF groups being the most reliable (m: 5.63/6.70), while C and HF10%60s (m: 2.78/2.73) were the least reliable. All fractures originated from surface defects on the treated side of specimens. The 5%HF groups showed higher μSBS (20 s: 21.35 ± 4.70 MPa; 60 s: 23.50 ± 4.27 MPa) than the 10%HF groups (20 s: 14.51 ± 2.47 MPa; 60 s: 16.54 ± 3.12 MPa) and C (6.46 ± 2.71 MPa). The most prevalent failure pattern was "mixed" for etched groups, and "adhesive" for C. Etching protocols affect the evaluated properties by roughening materials' surface and, in some cases, regularizing surface defects. The best overall outcomes were achieved when applying 5%HF.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Influence of different surface finishing procedures of strength-gradient multilayered zirconia crowns on two-body wear and fracture load: Lithium silicate or leucite glazing versus polishing?

Moritz Hoffmann,Felicitas Mayinger,Bogna Stawarczyk

DOI: https://doi.org/10.1016/j.jmbbm.2023.106307

IF: 4.042

2023-12-09

Journal of the Mechanical Behavior of Biomedical Materials

Abstract:Objectives To examine the influence of different finishing procedures on the surface roughness, wear resistance and fracture load of strength-gradient multilayered zirconia. Materials and methods Zirconia crowns (Multilayer 3D pro; n = 96) were manufactured and treated with a lithium-silicate- (LISI_S), leucite-based glaze spray (LEU_S), leucite-based glaze mass (LEU_M) or polished (POL). Natural molars (CG; n = 24) acted as a control. Roughness was determined on flat glazed specimens (n = 28). Two-body wear was examined by digitalizing and matching the occlusal surface before and after thermo-mechanical aging (6,000 thermal and 1,200,000 chewing cycles). The groups were split to measure fracture load initially and after aging. Kolmogorov-Smirnov, Spearman correlation, Kruskal-Wallis-H, Levene's test, one-way ANOVA with Scheffé post-hoc and Weibull modulus were computed. Results POL presented the lowest and LEU_S the highest roughness. Following POL, no ceramic loss was observed. LISI_S, LEU_S and LEU_M showed lower ceramic wear than the CG. The lowest wear of the antagonist was observed for the CG. LISI_S showed a lower antagonistic wear than LEU_S, LEU_M and POL. LISI_S, LEU_S, LEU_M and POL showed higher fracture load values and Weibull moduli than the CG. Artificial aging did not impact the fracture load or Weibull moduli. Significance With glazed groups showing height losses closer to the CG, glazing should be preferred to polishing when approximating the wear behavior of a natural dentition. Finishing of monolithic zirconia by glazing with a lithium silicate-based spray is recommended to preserve the antagonists. All examined zirconia crowns presented sufficient mechanical properties to withstand masticatory forces, even after prolonged aging.

engineering, biomedical,materials science, biomaterials
Enhancing Shear Bond Strength in Lithium Silicate Glass Ceramics: Surface Treatment Optimization for Reseating Protocols

Allison Torbiak,Muna Bebsh,Asmaa Haimeur,Ana Carla Fernandes,Cristina Fiuza,Rodrigo França

DOI: https://doi.org/10.3390/cryst14100856

IF: 2.7

2024-09-29

Crystals

Abstract:The rapid evolution of lithium silicate-based glass ceramics in the field of dental ceramics has led to the availability of different compositions in the market. This in vitro study was conducted to assess an effective protocol for recementing de-bonded lithium silicate-based glass ceramics by evaluating the shear bond strength of three reseating methods. The study included IPS e.max® CAD, Vita Suprinity®, Celtra Duo®, and n!ce as lithium-based glass ceramics. The samples underwent a series of preparation steps, including embedding in acrylic resin, hand polishing, etching with 5% hydrofluoric acid, and application of universal primer and adhesive as per manufacturer instructions. Subsequently, adhesive resin cement was applied to the ceramic tablets, and shear bond strength was assessed using a standardized method. The findings revealed that no single method demonstrated significantly superior results compared to the others. However, it was observed that etching with 5% hydrofluoric acid for 20 s yielded favorable outcomes in terms of time efficiency and standardized results. Additionally, it was noted that although sandblasting increased surface area, it did not enhance bond strength due to unfavorable surface disturbance. In conclusion, the study suggests that etching with 5% hydrofluoric acid for 20 s is a favorable protocol for reseating de-bonded lithium disilicate-based glass ceramics, offering both time efficiency and consistent results for clinicians.

materials science, multidisciplinary,crystallography
Lithium disilicate and zirconia reinforced lithium silicate glass-ceramics for CAD/CAM dental restorations: biocompatibility, mechanical and microstructural properties after crystallization

Luan Mavriqi,Francesco Valente,Giovanna Murmura,Bruna Sinjari,Monica Macrì,Oriana Trubiani,Sergio Caputi,Tonino Traini

DOI: https://doi.org/10.1016/j.jdent.2022.104054

Abstract:Objectives: The objective of this study was to define the impact of heating rate on the crystal growth, the mechanical properties, and the biocompatibility of three different kinds of CAD/CAM glass-ceramics treated with a conventional furnace. Methods: Lithium disilicate (IPS EMax-CAD, Ivoclar Vivadent) (LS2) and two zirconia reinforced lithium silicate (ZLS) ceramics (Vita Suprinity PC, VITA Zahnfabrik; Celtra Duo, Dentsply Sirona) (ZLSS; ZLSC) were used. The mechanical properties and the crystal growth were evaluated on 42 specimens (n = 14 per group). The thermal treatments recommended by the manufacturers were carried out. All groups were tested for fracture toughness (Ft) and Vickers hardness (Hv). Scanning electron microscope (SEM) images were taken after a slight surface etching with hydrofluoric acid solution (1% for 20 s). Differential Thermal Analysis (DTA) was performed and cellular adhesion with human periodontal ligament stem cells (hPDLSCs) culture was qualitatively assayed. Data were analyzed with Repeated Measurements ANOVA and ANOVA followed by Tukey post hoc test. Results: The crystals' mean size (±SD) after heat treatment was 1650.0 (±340.0) nm for LS2, 854.5 (±155.0) nm for ZLSS and 759.9 (±118.4) nm for ZLSC (p < 0.05 among the groups). As consequence of crystallization, the Hv was 6.1 ± 0.3 GPa for LS2, 7.6 ± 0.7 GPa for ZLSS and 7.1 ± 0.5 GPa for ZLSC (p < 0.05 for LS2 vs ZLSS and ZLSC), while the Ft was 2.2 ± 0.1 MPa m1/2 for LS2, 4.7 ± 0.8 MPa m1/2 for ZLSS and 3.8 ± 0.6 MPa m1/2 for ZLSC (p < 0.05 among the groups). The DTA curves showed a crystallization process for LS2, ZLSS and ZLSC at a temperature range 810-840 °C. The amount of adherent hPDLSCs was superior on LS2 than on ZLS. Conclusions: All the CAD/CAM materials can be properly crystallized if heat treated following the manufacturers' instructions. The crystallization process highly depends on temperature. ZLS glass ceramics show significantly inferior crystals dimensions and higher fracture toughness and Vickers hardness than LS2 ceramic. hPDLSCs cultured on LS2 have a superior adhesion than those cultured on ZLS. Clinical significance: The value of this study relies on the demonstration that a proper heat-treatment of CAD/CAM lithium disilicate and ZLS glass ceramics generates products that are suitable for clinical use . The differences highlightable in mechanical properties and biocompatibility behavior do not affect their successful clinical application.
Electrochemical behavior and degradation mechanism of lithium disilicate glass ceramics in acidic environment

Soraya Lakhloufi,Najoua Labjar,Houda Labjar,Malika Serghini‐Idrissi,Souad El Hajjaji

DOI: https://doi.org/10.1111/ijag.16653

2024-01-05

International Journal of Applied Glass Science

Abstract:IPS e.max Press lithium disilicate‐based glass ceramics are the most widely used ceramic type in restorative dentistry, renowned for their mechanical and aesthetic excellence. Our study delved into their degradation in the oral environment, employing electrochemical analyses and surface characterization techniques. The results reveal robust resistance to degradation in various acidic electrolytes, with differences in acid susceptibilities indicating nuanced behavior. This insight contributes to the advancement of durable dental materials, ensuring lasting smiles for patients. IPS e.max Press, a lithium disilicate‐based glass ceramic, is renowned in dental restorations for its mechanical strength and aesthetic appeal. This study delves into its behavior within oral environments, employing electrochemical and surface analysis techniques. By utilizing cyclic polarization curves and impedance spectroscopy, we evaluated its degradation resistance. Surface morphology, composition, and crystal stability were explored through scanning electron microscopy (SEM)/energy‐dispersive X‐ray spectroscopy (EDX) and X‐ray powder diffraction (XRD) analysis. The glass ceramic exhibited robust resistance to localized degradation across all tested electrolytes. The degradation potential (Ecorr) varied with time and pH, indicating electrolyte influence. SEM/EDX affirmed oxide layer formation, while XRD confirmed a stable structure. While showcasing favorable resistance in saliva, citric acid, and lactic acid, IPS e.max Press demonstrated susceptibility to acetic acid. This comprehensive analysis enhances our understanding, providing valuable insights for the development of durable dental materials through a combination of electrochemical analysis and surface characterization.

materials science, ceramics
[Sinusitis in children].

J. Maurer,W. Mann

1956-01-31

Abstract:
Silica infiltration on translucent zirconia restorations: Effects on the antagonist wear and survivability

Larissa Marcia Martins Alves,Camila da Silva Rodrigues,Nathalia de Carvalho Ramos,Jeff Buizastrow,Tiago Moreira Bastos Campos,Marco Antonio Bottino,Yu Zhang,Renata Marques de Melo

DOI: https://doi.org/10.1016/j.dental.2022.11.015

IF: 5.687

2022-11-27

Dental Materials

Abstract:Objective To assess potential antagonist wear and survival probability of silica-infiltrated zirconia compared to glass-graded, glazed, and polished zirconia. Methods Table top restorations made of 3Y-TZP (3Y), 5Y-PSZ (5Y), and lithium disilicate (LD) were bonded onto epoxy resin preparations. Each zirconia was divided into five groups according to the surface treatment: polishing; glaze; polishing-glaze; glass infiltration; and silica infiltration. The LD restorations received a glaze layer. Specimens were subjected to sliding fatigue wear using a steatite antagonist (1.25 ×10 6 cycles, 200 N). The presence of cracks, fractures, and/or debonding was checked every one/third of the total number of cycles was completed. Roughness, microstructural, Scanning electron microscopy, wear and residual stress analyses were conducted. Kaplan–Meier, Mantel–Cox (log-rank) and ANOVA tests were performed for statistical analyses. Results The survival probability was different among the groups. Silica infiltration and polishing-glaze led to lower volume loss than glaze and glass-infiltration. Difference was observed for roughness among the zirconia and surface treatment, while lithium disilicate presented similar roughness compared to both glazed zirconia. Scanning electron microscopy revealed the removal of the surface treatment after sliding fatigue wear in all groups. Compressive stress was detected on 3Y surfaces, while tensile stress was observed on 5Y. Significance 3Y and 5Y zirconia behaved similarly regarding antagonist wear, presenting higher antagonist wear than the glass ceramic. Silica-infiltrated and polished-glazed zirconia produced lower antagonist volume loss than glazed and glass-infiltrated zirconia. Silica-infiltrated 3Y and lithium disilicate restorations were the only groups to show survival probabilities lower than 85%.

materials science, biomaterials,dentistry, oral surgery & medicine

Distance diagnosis in pediatric cardiology: a model for telemedecine implementation.

Effect of simulated gastric acid exposure on the hardness, topographic, and colorimetric properties of machinable and pressable zirconia-reinforced lithium silicate glass-ceramics

Impact of Gastric Acid Induced Surface Changes on Mechanical Behavior and Optical Characteristics of Dental Ceramics

Effect of different surface treatments on optical, colorimetric, and surface characteristics of a lithium disilicate glass-ceramic

Surface Roughness Examination of Glass Ionomer Restorative Cements Treated with Acidic and Basic Pediatric Medications: An In Vitro Study

Barriers to maternal health service use in Chikhwawa, Southern Malawi.

Effect of Glazing Protocol on the Surface Roughness and Optical Properties of Lithia-Based Glass-Ceramics

Staining and bleaching susceptibility of zirconia-reinforced lithium silicate glass-ceramics with different thicknesses, translucencies, and fabrication methods

Erwin Uehlinger und Herwig Hamperl 70 Jahre alt

Regularization of linear ill-posed problems by the augmented Lagrangian method and variational inequalities

Impact of glazing on wear, fracture load, and optical properties of a new fully crystallized lithium disilicate ceramic material

Effect of repeated firing on the topographical, optical, and mechanical properties of fully crystallized lithium silicate-based ceramics

Suicide among the young--the size of the problem.

Optimal Hydrofluoric Acid Etching Duration and Impact of Silane/Adhesive on Profilometric Properties and Bonding to Lithium Disilicate Glass Ceramics

Mechanical, Adhesive and Surface Properties of a Zirconia-Reinforced Lithium Silicate CAD/CAM Ceramic Exposed to Different Etching Protocols

Influence of different surface finishing procedures of strength-gradient multilayered zirconia crowns on two-body wear and fracture load: Lithium silicate or leucite glazing versus polishing?

Enhancing Shear Bond Strength in Lithium Silicate Glass Ceramics: Surface Treatment Optimization for Reseating Protocols

Lithium disilicate and zirconia reinforced lithium silicate glass-ceramics for CAD/CAM dental restorations: biocompatibility, mechanical and microstructural properties after crystallization

Electrochemical behavior and degradation mechanism of lithium disilicate glass ceramics in acidic environment

[Sinusitis in children].

Silica infiltration on translucent zirconia restorations: Effects on the antagonist wear and survivability