Abstract:The stiffness of machine tools is a key factor to increase the productivity. The dynamic stiffness dominates the stable cutting conditions, where forced and regenerative chatters do not occur. In general, dynamic stiffness is measured using an impact hammer as it does not require the particular device setting. However, humans should use a hammer and impact control needs skills. To this end, several researches have been conducted to establish automatic excitation methods. To measure the dynamic stiffness of a rotating spindle, authors have developed an electromagnetic biaxial excitation device which can generate biaxial force. This paper presents the measurement result of dynamic stiffness for both the structure and spindle of a five-axis machining center using the developed device. INTRODUCTION For the avoidance of chatter vibrations in machining, chatter mechanism and suppression methods have been studied [1]. One of the well-known techniques is chatter prediction using stability limit diagrams (SLDs), where the relation between the limit of depth of cut and spindle speed is analyzed and shown graphically. For the prediction of the stability limit accurately, it is necessary to measure the precise dynamic compliance of the machine. In general, dynamic stiffness is measured using an impact hammer for its simplicity. However, humans should use a hammer with skills. To this end, several researches have been conducted to establish automatic excitation methods [2-4], which are categorized into contact and contact-less methods. The noncontact excitation method has been developed to analyze the dynamics of rotating spindle. It also can explain the dynamics of machine structure comparably. This paper presents the analysis of both the structure and spindle of a five-axis machining center using the developed device. Through the measurement tests, anisotropic in stiffness were investigated. MEASUREMENT SYSTEM Figure 1 (a) shows the schematic of a developed biaxial electromagnetic excitation device [5]. The device consists of iron cores, coils, yoke (housing) and its cross-section view is shown in Fig. 1 (b). A dummy tool attached to the spindle is inserted into the hole, facing to the coils with air-gap. Giving current to two coils generate magnetic flux, flown to the surface of the dummy tool and the yoke. Thus, two coils can produce a single attraction fore in a single direction. Eight coils generate biaxial force (x and y) in plus and minus directions. Yoke diameter:φ220 mm Hight : 160 mm (a) Isometric view (b) Sectional view Figure 1: Schematic of electromagnetic excitation device. Figure 2 shows the experiment and measurement system. The excitation device was installed on the machine tool table of a five-axis machining center, where a dynamometer was placed on the table to measure attractive forces. The dummy tool that integrates a holder interface was attached to the spindle. Displacement sensors were installed at the upper case of the housing, measuring the holder displacement of the dummy tool in the xand the y-directions. A control PC sent a swept-sine current command to an amplifier that gives coil current to Coil Housing Iron core 22.5° 22.5°

Dynamic measuring of force-displacement-characteristics of shockmounts

Quantitative Analysis of Tubular Dual-Armature Switched Flux Permanent Magnet Machines for Shock Absorbers

Response and Performance of A Nonlinear Vibration Isolator with High-Static-Low-Dynamic-Stiffness under Shock Excitations

A Hardware-in-the-Loop Approach to Test Rotary Electromagnetic Shock Absorbers

Virtual Accelerometer Approach to Create Vibration Profile for Automotive Component Shake Test

Dynamic force measurement to assess NVH performance of electric motors

Analytical Model of Structural Damping in Friction Module of Shell Shock Absorber Connected to Spring

Novel method for load acquisition for the shock absorber upper strut mount of an automotive suspension system

Measurement uncertainty evaluation of a hexapod-structured calibration device for multi-component force and moment sensors

Intelligent Force-Measurement System Use in Shock Tunnel

A Transfer Function Approach to Shock Duration Compensation for Laboratory Evaluation of Ultra-High-G Vacuum-Packaged MEMS Accelerometers

Shock absorber lateral and impact force measurement using a column-type sensor

Vision and Vibration Data Fusion-Based Structural Dynamic Displacement Measurement with Test Validation

INVESTIGATION OF DYNAMIC STIFFNESS OF MACHINE TOOL WITH ELECTROMAGNETIC BIAXIAL EXCITATION DEVICE

Testing and mathematical approach on dynamics of a cymene-Si-oil shock absorber for structural integrity in vibration and impact protection

Nonlinear damping quantification from phase-resonant tests under base excitation

A hybrid modeling approach for automotive vibration isolation mounts and shock absorbers

Dynamic plastic hinge rotation measurement for RC columns under seismic loads using MEMS inclinometers

Measurement of Dynamic Characteristics on Structure using Non-marker Vision-based Displacement Measurement System

High-Impact Dynamic Loading Method for Calibration of Triaxial Acceleration Sensors

Dynamic Response and Identification of Critical Points in the Superstructure of a Vehicle Using a Combination of Numerical and Experimental Methods