Abstract:Pure Titanium (Titanium grade 2) and Ti6Al4V (Titanium grade 5) alloys are commonly used biocompatible materials for medical bone implants and dental protheses. As some implants have to be removed after a certain amount of time after the implantation, the osteo repellent surface is one of the most important property for the removable bone implants such as bone screws and plates. On contrary, for the dental protheses the property of the most importance is osseointegration. Femtosecond laser treatment causes ablation and produces LIPSS ("laser induced periodic surface structures") which can consist of cones on macro scale and ripples on nano scale which showed structures and roughness similar to that of a bone. Therefore, surface modifications by electrochemical anodization and femtosecond laser could be seen as promising methods for improving both osteo-repellence and osteointegration properties of the bone implants and dental protheses. The aim of this work is electrochemical and surface characterization of the anodized Titanium and Ti6Al4V alloy treated by the femtosecond laser. Firstly, Titanium and Ti6Al4V samples were anodized potentiostaticaly up to 100V in 25% phosphoric acid solution for 120s. Following the potentiostatic anodization, samples were structured with femtosecond laser to produce micro cones and nano ripples on top of the cones. As a final step, laser treated spots were potentiodynamicaly anodized using a SDCM (Scanning Droplet Cell Microscopy) setup. Influence of different potentials, scan rates and electrolytes were studied and optimized, consequently. Morphology and topography were examined by the means of SEM (Scanning Electron Microscopy) and AFM (Atomic Force Microscopy), while crystallography was determined by the XRD (X-Ray Diffraction). Furthermore, the composition of the oxide layer was determined by the XPS (X-ray photoelectron spectroscopy). Oxide forming factor (k ox ), a relative permittivity ε r , and ECSA (Electrochemical surface area) were obtained from the cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) experimental data. Electrochemical impedance spectroscopy data was modeled and compared between not preanodized, preanodized and anodized and not anodized after femtosecond laser structuring. Finally, bioassessment with osteoblast was done to examine the growth of the osteoblast cells on the modified surface structures. Value of the oxide forming factor (k ox ) for the pure Titanium and Titanium grade 5 were successfully calculated and compared with a Scanning Electron Microscopy. Calculated values of the relative permittivity ε r are in agreement with the literature values. Finally, obtained results indicate that anodized and subsequently femtosecond laser treated samples could be used as medical bone and dental implants.

The utility of p16INK4a and Ki‐67 staining on cell blocks prepared from residual thin‐layer cervicovaginal material

Picosecond laser induced hybrid groove structures on Ti6Al4V bio-alloy to accelerate osseointegration

Magnesium sulphate infusion suppresses the cardiac release of noradrenaline during a handgrip stress test.

Nucleolar organizer regions (NORs) in normal and pathological liver: a quantitative analysis.

Impact of Laser Structuring on Medical-Grade Titanium: Surface Characterization and In Vitro Evaluation of Osteoblast Attachment

Cells in lesions of mycosis fungoides lymphoma following therapy: Changes in number and type

Influence of Laser Treatment of Ti6Al4V on the Behavior of Biological Cells

Biocompatibility of Ti-6Al-4V titanium alloy implants with laser microgrooved surfaces

Electrochemical Surface Characterization of a Femtosecond Laser Treated and Anodized Ti and Ti6Al4V Alloy for Bone and Dental Implants

Propagation characteristics of ferrite loaded inset dielectric guide

Bioinspired surface hierarchical microstructures of Ti6Al4V alloy with a positive effect on osteoconduction

Single‐ and Multiscale Laser Patterning of 3D Printed Biomedical Titanium Alloy: Toward an Enhanced Adhesion and Early Differentiation of Human Bone Marrow Stromal Cells

Laser-Assisted Nanotexturing and Silver Immobilization on Titanium Implant Surfaces to Enhance Bone Cell Mineralization and Antimicrobial Properties

Femtosecond laser treatment promotes the surface bioactivity and bone ingrowth of Ti6Al4V bone scaffolds

Bio‐Inspired Micro‐ and Nano‐Scale Surface Features Produced by Femtosecond Laser‐Texturing Enhance TiZr‐Implant Osseointegration

Osteon-mimetic laser-structured Ti-6Al-4V supports for guided stem cell growth

Evading stability-biocompatibility tradeoff in TiNb coatings with armour-like super hydrophilic micro-nano structure surface

Surface modification of Ti6Al4V by nanosecond laser ablation for biomedical applications

[Renovascular hypertension: apropos of a case with collateral renal circulation].

Laser beam melting 3D printing of Ti6Al4V based porous structured dental implants: fabrication, biocompatibility analysis and photoelastic study

Agreement among four homocysteine assays and results in patients with coronary atherosclerosis and controls.