Abstract:Pure Titanium (Titanium grade 2) and Ti6Al4V (Titanium grade 5) alloys are commonly used biocompatible materials for medical bone implants and dental protheses. As some implants have to be removed after a certain amount of time after the implantation, the osteo repellent surface is one of the most important property for the removable bone implants such as bone screws and plates. On contrary, for the dental protheses the property of the most importance is osseointegration. Femtosecond laser treatment causes ablation and produces LIPSS ("laser induced periodic surface structures") which can consist of cones on macro scale and ripples on nano scale which showed structures and roughness similar to that of a bone. Therefore, surface modifications by electrochemical anodization and femtosecond laser could be seen as promising methods for improving both osteo-repellence and osteointegration properties of the bone implants and dental protheses. The aim of this work is electrochemical and surface characterization of the anodized Titanium and Ti6Al4V alloy treated by the femtosecond laser. Firstly, Titanium and Ti6Al4V samples were anodized potentiostaticaly up to 100V in 25% phosphoric acid solution for 120s. Following the potentiostatic anodization, samples were structured with femtosecond laser to produce micro cones and nano ripples on top of the cones. As a final step, laser treated spots were potentiodynamicaly anodized using a SDCM (Scanning Droplet Cell Microscopy) setup. Influence of different potentials, scan rates and electrolytes were studied and optimized, consequently. Morphology and topography were examined by the means of SEM (Scanning Electron Microscopy) and AFM (Atomic Force Microscopy), while crystallography was determined by the XRD (X-Ray Diffraction). Furthermore, the composition of the oxide layer was determined by the XPS (X-ray photoelectron spectroscopy). Oxide forming factor (k ox ), a relative permittivity ε r , and ECSA (Electrochemical surface area) were obtained from the cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) experimental data. Electrochemical impedance spectroscopy data was modeled and compared between not preanodized, preanodized and anodized and not anodized after femtosecond laser structuring. Finally, bioassessment with osteoblast was done to examine the growth of the osteoblast cells on the modified surface structures. Value of the oxide forming factor (k ox ) for the pure Titanium and Titanium grade 5 were successfully calculated and compared with a Scanning Electron Microscopy. Calculated values of the relative permittivity ε r are in agreement with the literature values. Finally, obtained results indicate that anodized and subsequently femtosecond laser treated samples could be used as medical bone and dental implants.

Surface modification of Ti6Al4V by nanosecond laser ablation for biomedical applications

Effect of different laser texture configurations on improving surface wettability and wear characteristics of Ti6Al4V implant material

Picosecond laser texturing on titanium alloy for biomedical implants in cell proliferation and vascularization

Characterization of Ti6Al4V Alloy Produced by Laser-Powder Bed Fusion and Surface Modification Using Nanosecond Laser

Biological Characterization of Ti6Al4V Additively Manufactured Surfaces: Comparison Between Ultrashort Laser Texturing and Conventional Post‐Processing

A novel nanosecond pulsed laser textured moat configurations for enhancing surface wettability, corrosion and tribology behaviour of Ti6Al4V implant material

Study on surface properties of nanosecond laser textured plasma nitrided titanium alloy

Enhancing Bactericidal Properties of Ti6Al4V Surfaces through Micro and Nano Hierarchical Laser Texturing

Surface Modification of Ti3Al2.5V Titanium Alloy Using Laser Texturing With Improved Wettability, Corrosion and Bioactivity Behaviour

Improving the Bio-Tribological Properties of Ti6Al4V Alloy via Combined Treatment of Femtosecond Laser Nitriding and Texturing

Biological response of laser macrostructured and oxidized titanium alloy: an in vitro and in vivo study

The influence of laser texturing on the tribological behavior of titanium alloy Ti6Al4V in medical applications

Influence of Laser Treatment of Ti6Al4V on the Behavior of Biological Cells

Surface texturing of Ti6Al4V alloy using femtosecond laser for superior antibacterial performance

Laser surface modification of Ti--6Al--4V: wear and corrosion characterization in simulated biofluid

Influence of Power and Frequency in the Femtosecond Laser Texturing of Ti6Al4V

Fabrication of multifunctional titanium surfaces by producing hierarchical surface patterns using laser based ablation methods

Biocompatibility of Ti-6Al-4V titanium alloy implants with laser microgrooved surfaces

Electrochemical Surface Characterization of a Femtosecond Laser Treated and Anodized Ti and Ti6Al4V Alloy for Bone and Dental Implants

Evading stability-biocompatibility tradeoff in TiNb coatings with armour-like super hydrophilic micro-nano structure surface

In Vitro Bioactivity and Biocompatibility of Bio-Inspired Ti-6Al-4V Alloy Surfaces Modified by Combined Laser Micro/Nano Structuring