Abstract:Spark-ignition direct-injection (SIDI) gasoline engine, especially in downsized boosted engine platform, has proven to be one of the most promising concepts to improve vehicle fuel economy. SIDI engines are also getting a larger share of the gasoline engine market which is traditionally dominated by the port fuel injection (PFI) engines in the U. S., European and Chinese vehicles. However, higher particle number emissions associated with operating the engine at higher loads pose additional challenges for meeting future stringent emissions regulations. In this study, the potential of using multiple injection strategies (double injection and triple injection strategy during the intake stroke in homogeneous combustion mode) to reduce particle number emissions in a 2.0 liter boosted SIDI gasoline engine at 1000 rpm, 11 bar BMEP condition was investigated using Horiba MEXA SPCS1000 PN measurement instrument. To clarify the mechanism for the particle emissions benefit by multiple injection strategies, three-dimensional (3D) Computational Fluid Dynamics (CFD) model of the in-cylinder process was realized using CONVERGE software with the inputs from GT-Power (R) engine simulation.Measurements indicate that the double injection strategy causes a 60% reduction in particle number concentration and up to 80% reduction when implementing triple injection strategy as compared to baseline single injection strategy, demonstrating the potential of multiple injections as a promising strategy for lower particle emissions at high load operating conditions. The 3D CFD simulation reveals that double injection is beneficial to the reduction of spray-piston and sprayliner impingement, and the improvement in mixture preparation process, resulting in lower levels of particles. For triple injection strategy, the spray impingement is further reduced, and the fuel is better mixed with air, leading to a significant reduction in particle formation. Regardless of double injection and triple injection strategy, the particle number emissions tend to increase when retarding the final injection timing. While, reducing the first injection mass is beneficial for lower particle number emissions both for double injection and triple injection strategies during the intake stroke.

Experimental studies on the particulate matter emission characteristics of a lateral swirl combustion system for direct injection diesel engines

Numerical analysis of mixing and combustion characteristics of a lateral swirl combustion system in OP2S diesel engines

Combustion performance and energy distributions in a new multi-swirl combustion system

Experimental studies on the dual-fuel sequential combustion and emission simulation

A comparative analysis of the performances of a syngas port injection plus gasoline direct injection combined-injection spark-ignition engine under lean-homogeneous charge and Lean-Stratified Charge modes

Particle Size Distributions and OC, EC Emissions from a Diesel Engine with the Application of In-Cylinder Emission Control Strategies

An Experimental Study on Combustion and Particulate Emissions Characteristics on a Dual-Injection Gasoline Engine

Experimental Investigation Of Impacts Of Engine Hardware, Operating Parameters And Combustion Performance On Particulate Emissions In A Disi Engine (Withdrawn Publication. See Vol. 215, Pg. 809, 2018)

Experimental Study of Stratified Lean Burn Characteristics on a Dual Injection Gasoline Engine

Experimental Investigation of Homogeneous Charge Induced Ignition (hcii) with Low-Pressure Injection to Reduce Pm Emissions in A Heavy-Duty Engine

A Computational Investigation of Piston Bowl Geometry and Injector Spray Pattern Effects on Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

Experimental Investigation and Numerical Modeling of Spray Combustion and Emission in a Diesel Engine

Anatomy of the Cooled Egr Effects on Soot Emission Reduction in Boosted Spark-Ignited Direct-Injection Engines

Effects of piston shapes and swirl ratios on combustion and emissions of a natural gas engine ignited by micro diesel pilot

Effect of Multiple-Injection Strategies on Diesel Engine Exhaust Particle Size and Nanostructure

Particle Number Emissions Reduction Using Multiple Injection Strategies in A Boosted Spark-Ignition Direct-Injection (sidi) Gasoline Engine

Application of CFD, Taguchi Method, and ANOVA Technique to Optimize Combustion and Emissions in a Light Duty Diesel Engine

Experimental investigation on the combustion and emissions in a pilot ignited direct injection natural gas engine using HCDI strategy

Differences in Pool-Fire Induced Soot Production Between Subcooled Spray and Flash Boiling Spray in a DISI Engine

Evaluation of the effects of injection timing and rate-shape on diesel low temperature combustion using advanced CFD modeling

Investigation on the gaseous and particulate emissions of a compression ignition engine fueled with diesel-dimethyl carbonate blends.